Sune Technology QPI-BM12 Manual

Your best partner for better driving
SUNE TECHNOLOGY CO.,LTD
No.9,Lane 606,Anping Rd,Tainan City 70849,TAIWAN
TEL:[phone] FAX:[phone]
Http://www.sune-tech.com
Shop http://www.carnavi-tech.com
SKYPE:sune_tech or hsin_han99
CarNavi-Tech

Warning
When installing the main unit, do not remove or alter existing
vehicle fasteners, including nuts, bolts, screw, clips, and fittings.
Never detach, move or alter existing vehicle wiring, including
electrical grounds and straps. Alteration of existing vehicle
components may make vehicle unsafe to operate. Should be
no any electronic devices or magnetic pole around installation
place.
Air bags are vital part of a safety system. Never install main unit
in a way which will alter air bag wiring or interfere with air bag
deployment. Air bags must function properly in the event of an
accident.
Before installing, check the location of pipe, tank, electrical
cables and others.
Read and follow the instruction manual.
Wiring location must not interfere driving, get in or out from car.
Use electrical tape to insulate the ends of all wires, even if they
are not used. Proper insulation prevents arcs, shocks and fires.
When installation is complete, test all vehicle electrical systems
to ensure they operate correctly, including lights, horn, brake
lights, and emergency flashers.
According to our sales policy, any problems caused by user’s
mistake, careless can not be guaranteed.
Caution
All steps of installation should be done by well-trained specialist.
During installation ignition key should be taken off and after all
installation finish connect power cable with interface for the last
step.
Do not install the main unit in places where it ma be exposed to
dew condensation (around the air conditioning hose, etc), or in
locations where it may come in contact with water, high levels of
moisture, dust or oily smoke
Install wiring in a manner in which cables will not come in contact
with metal parts. The wiring may be damaged by contact with
metal parts, resulting in fire and shocks. Avoid all contact with hot
surfaces when wiring the main unit. High temperatures may
damage wiring, causing shorts, arcing and fires.
Kindly check all parts are in the box, when receiving the product, if
anything missing, inform to the supplier or manufacturer.
Warning / Caution
CarNavi-Tech

Table of Contents
1. Specifications
1.1 Main Specifications
1.2 Features
1.3 System Diagram
1.4 Components
1.5 Exterior
2. Installation
2.1 Installation Diagram
2.2 Installation
3. Settings
3.1 DIP Switch
3.2 Remote Control
3.3 Car Model and Navi Model
3.4 Factory Mode
3.5 DVD, DTV I-DRIVE input
3.6 Original Button Usage
3.7 PIP setup
3.7.1 POP Set up
3.7.2 Switch Modes
3.8 Rear Camera
3.8 Rear Parking Guidelines
3.10 OSD
4. Trouble Shooting
4
5
6
7
9
10
11
13
14
15
16
19
21
23
24
25
26
27
30
32
CarNavi-Tech

1. Specifications
1.1 Main Specifications
1. Car Compatibility
BMW New 1,3,5,7 series 6.5’’ & 8.8’’ & 10.2”
2. Components
Interface* 1EA
3. MULTIMEDIA INTERFACE input specification
3 * A/V input (video external input)
1 * CVBS(Rear Camera) input
1 * Analog RGB input (Navigation system output)
1 * LCD input (Car system input)
4. MULTIMEDIA INTERFACE output specification
1 * LCD output
5. Power specification
Input power : 8VDC ~ 18VDC
Consumed power : 5WATT
6. Switch input mode
- External display skip function : through DIP switch, can
control each video input
- Through remote control, can change input mode
- Through CAN or rear lamp cable, rear camera can be
detected
4
CarNavi-Tech

1. Specifications
Easy installation through connection with commander
Able to control NAVI, DVD, DTV function by using I-Drive
Controller
Able to adjust DVD, NAVI display on screen
Improved Screen Display (user-oriented interface)
Mode change through original button (I-DRIVE MENU
BUTTON)
Provide power cable to connect with rear camera
Support PIP display –show original Navi and other source
display at the same time (Picture in Picture)
Dynamic PAS(Parking assistance system), moving parking
line according movement of steering wheel
1.2 Features
5
CarNavi-Tech

1. Specifications
1.3 System Diagram
DISPLAY
A/V 1
NAVIGATION Input
(Analog RGB)
CVBS
(Rear camera)
Car Screen Input
(CAR MAIN BOARD)
A/V 2
A/V 3
VIDEO
CIRCUIT
VIDEO MUX
MCU
Power Input
(+8VDC ~ +18VDC)
POWER
CIRCUIT
Dip S/W
A/V OUT HEADREST
MONITOR
Remote control Switch for source toggle
OEM Button (Can Signal)
Car Installation
OEM LCD
Rear Camera Power
(+9VDC)
6
CarNavi-Tech

1. Specifications
1.4 Components
A/V cable * 1EA
Mode cable * 1EA
IR cable * 1EA
R-CAM POWER cable * 1EA
(HARETC0002)
(HAVCAB0002)
Remote control * 1ea
(REMOTE0001)
(HARETC0001)
(HIRCAB0002)
TOUCH OUT cable * 1ea
(HTOUCH0004)
LCD Cable * 1ea
(HLCDCA0019)
TOUCH IN cable * 1ea
(HTOUCH0009)
RGB cable * 1ea
(HRGBCA0013)
LVDS Extension Cable * 1ea
(HLCDCA0022)(Optional)
Extension Sub-board * 1ea
(QCPASS0414)(Optional)
7
POWER cable (7P) * 1EA
(HPOWER0065)
POWER cable * 1EA
(HPOWER0045)
CarNavi-Tech

1. Specifications
1.4 Components
8
10.2” Touch Panel
(TOUPAN0002)
8.8” Touch Panel
(TOUPAN0012)
CarNavi-Tech

1. Specifications
1.5 Exterior
①⑥⑦⑧
①MODE
②IR
③POWER
④TOUCH OUT TO NAVI
⑤TOUCH IN FROM LCD
⑥R-CAM
⑦RGB-IN
⑧AV IN/OUT
⑨LCD-OUT
⑪TEST
Dimension
Width 150.4mm
Length 99.4mm
Height 2.3.2mm
⑩LCD-IN
②③④⑤
⑫LED
⑬DIP S/W
⑨⑩⑪⑫⑬
9
CarNavi-Tech

2. Installation
2.1 Installation Diagram
Provided
LCD cable
OEM
Monitor
AV1 AV2 AV3 REAR C
Audio L
Audio R
AV/OUT Video
REAR (9V OUT)
GND
B DATA (blue) SYNC GND
IR-DTV
NAVI-VS
IR-NAVI
IR-DVD
R DATA (red) G DATA (green)
10
Original LCD Cable
<Behind of Radio System>
CarNavi-Tech

2. Installation
2.2 Installation / Monitor and Interface connection
①See left picture, Remove
original LCD cable from
monitor and connect with
provided LCD cable.
②Connect the original LCD
cable with LCD-IN on the
interface.
※Precaution : Do not connect power cable with accessory
power, connect with backside of command or cigar jack.
11
CarNavi-Tech

2. Installation
2.2 Installation / connect Power cable
12
Connect with
Interface
Connecting
Connecting
<Behind of Radio System>
<Original Cable>
Connecting
※ Connect original cable after taking out from Radio system
<Interface>
※ Plug & Play without fiber optic cables
- You are required to connect original
fiber optic cables to the supplied plug &
play connector
Example
CarNavi-Tech

3. Settings
3.1 DIP Switch
PIN
Function
Dip S/W Selection
1
Displaying RGB input
ON : RGB mode skip
OFF : RGB mode display
2
Displaying A/V 1
ON : A/V 1 mode skip
OFF : A/V1 mode display
3
Displaying A/V 2
ON : A/V 2 mode skip
OFF : A/V2 mode display
4
Displaying A/V 3
ON : A/V 3 mode skip
OFF : A/V3 mode display
5
Setup of monitor size
ON : 6.5”
OFF : 8.8”, 10.2”
6
Setup of Rear camera mode
(F20)
*** F56 is not applicable
ON : 3D GUI model
OFF : Standard GUI model
7
Setup of rear camera use
ON : CVBS4
OFF : MAIN
8
N.C
※ON : DOWN / OFF : UP
Default : DIP S/W 8 OFF
※Example DIP S/W usage
- Use input mode : A/V2, A/V3
- Use original navigation
- External rear camera
▷DIP S/W : 1,2 ON (hide INPUT MODE)
▷DIP S/W : 3 OFF (A/V2 display)
▷DIP S/W : 4 OFF (A/V3 display)
▷DIP S/W : 5 OFF (8.8” & 10.2”)
▷DIP S/W : 6 OFF (Standard GUI model)
▷DIP S/W : 7 ON (display external rear cam)
▷DIP S/W : 8 OFF
13
※Please make sure to disconnect the power cable of the interface and reconnect
the power cable again to apply the dip switch setting whenever changing DIP switch.
Otherwise, DIP switch setting will not be applied.
※In Case of New 2Series, X3,X4, New X-Series(8.8”), i8 should be set
Dip S/W #5, #6 to Down
※In Case of New 1Series happen “no signal” problem, Dip S/W #5, #8 to Down
※Put Dip # 5,6,7 “On” in order to select “15YHarman” in PDC type on the
factory mode(Refer to pg26)
CarNavi-Tech

3. Settings
3.2 Remote Control
Key
Function
POWER & PIP Unavailable
MENU Activating OSD menu
OK Making a selection, changing image display
▲Moving upward
▼Moving downward
◀
Moving leftward
(If you press this button 2 seconds long, you can access the factory
mode.)
▶
Moving rightward
(If you press this button 2 seconds long, you can reset all the
data about user environment.)
14
CarNavi-Tech

3. Settings
3.3 Car Model and Navi Model
IMAGE
Adjust navigation position and size
H-POSITION : Move display horizontally
V-POSITION : Move display vertically
H-SIZE : Adjust navi size horizontally
UTIL1 - CAR MODEL
Selecting model of the car
F20 : 1, 3, 5, 7 series 6.5” & 8.8”
New UI 8.8” 10.2”
F56 : New MINI, New X3 6.5”
F20 NEW : 1, 3, 5, 7 series 6.5” &
8.8” 2016 ~
F56 NEW : New MINI, New X3 6.5”
2016~
*Select the New model if having
a problem of screen flicking with
cars after Oct 2016.
UTIL1 –NAVI MODEL
Select navigation model
DEFAULT
LS901
PAPAGO
QROI
KD900
ACLASS
GI5000A
GI8000N
HDMI
WP9200
MYVI
NAV_506TP
ICUBE
GN_3000
NAVIST
PAPAGO
SMITH_PAD
* Go into FACTORY/ IMAGE (as
shown right) and adjust the
position and the size of the
navigation after setting the
definition of the navigation
FACTORY mode –Press ◀button 2 seconds long on the remote control.
Setup for car model Setup for navigation
15
CarNavi-Tech

3. Settings
3.4 FACTORY Mode
UTIL1 –AVOUT SELECT
Selecting background sound
After
returning navigation or original
mode
DEFAULT : Selecting AV sound
just before changing
navigation or original mode
from the AV mode
AV 1~3 : Sound of the selected
AV source 1~3
UTIL1 - FACTORY RESET
FACTORY MODE RESET
FACTORY mode –Press ◀button 2 seconds long on the remote control.
16
CarNavi-Tech

3. Settings
3.4 FACTORY Mode
UTIL2 - I_DRV CONTROL
Selecting whether to use I_DRV
function or not
ON / OFF
A/V1 : Control DVD Remote control
UI
A/V2 : Control DTV Remote control
UI
UTIL2 - I_DRV REMOTE
Choose DTV and DVD model
to be control I_DRV function
LI-1DISC
NEC-6DISC
USER(when using IR MEMORY)
•Select DVD model: Setting on
AV1 Mode
•Select DTV model : Setting on
A/V2 mode
FACTORY mode –Press ◀button 2 seconds long on the remote control.
17
CarNavi-Tech

3. Settings
3.4 FACTORY Mode
FACTORY mode –Press ◀button 2 seconds long on the remote control.
UTIL2 –HANDLE KEY
Whether to use voice button
on handle for mode change
ON / OFF
UTIL2 –IR MEMORY
To register DVD, DTV remote control,
the remote control value must be
registered and can be control with
I-Drive
DVD(A/V1), DTV(A/V2)
※To use this function, in UTIL2-
I_DRV REMOTE select USER mode
DVD / DTV
UTIL2 –MEMORY KEY
Wheter to use car audio
button #8 (mode change +
aux change : F20)
ON / OFF
* F56 : #6 ON / OFF
UTIL2 –CALIBRATE
Touch Calibration
YES / NO
18
CarNavi-Tech

3. Settings
3.5 DVD, DTV IR MEMORY input
①First of all, press ◀button on
remote controller 2 seconds
long or press
UP→DOWN→UP→MENU
button in order to access
Factory mode. Choose IR
MEMORY on UTIL2.
In IR MEMORY, you can choose
AV source of DTV and DVD you
want to use.
②Picture above shows DVD
remote control button value
input, select menu you want
to save. (To register DVD
remote control button value,
select IR MEMORY –DTV and
follow below instructions.
Example)
a. After select OK button on
OSD menu, press intended I-
Drive button
b. Indicated part above will
flicker, and press POWER on
DVD remote control.
(continue to next page)
What is IR-MEMORY Mode?
Is to allow I-Drive and touch screen to control other DVD or DTV
(besides the existing,; for example : SANYO, NECVOX) by register
remote control value.
19
CarNavi-Tech

3. Settings
3.5 DVD, DTV I-DRIVE input
example) continued..
c. The values that you
registered will appear as
green text in the marked
area on pressing the button.
And the values will be saved
automatically.
d. Register remain buttons’
value in OSD menu like the
above-mentioned.
③After register, select “SRC”
button in OSD menu. Then you
can see confirmation window
as shown above. At the
moment,
(If data is saved, DVD TYPE and
DTV TYPE will be changed to
“USER” automatically.)
If you see “SUCCESS” on screen,
the data is saved clearly and
you can control DVD via touch
screen. BUT, you MUST change
the option in FACTORY-UTIL2-
I_DRV REMOTE to “USER”.
※ When touch the screen, you can control DVD, DTV using remote control UI
via touch screen or I-Drive
(6.5” monitor –Touch the middle of the screen,
8.8”, 10.2” monitor –Touch the left side of the screen)
※ If touch the screen in DVD(A/V1), DTV(A/V2) mode, Can see remote control UI
If touch the screen in RGB(HDMI), A/V3 mode, Can see mode switching UI
- If you want to see mode switching UI in DVD, DTV mode, Select “SRC” button
20
CarNavi-Tech