SUNFLEX DESKFRAME 600602 User manual

EN
Assembly manual
Rev. 20221207
1 (11)
www.sun-flex.com
SUN-FLEX®DESKFRAME 600602
SUN-FLEX®DESKFRAME 600702
SUN-FLEX®DESKFRAME 600802

EN
2 (9)2 (11)
-Attach the control box to the motor cable/cables.
-Attach the power cable to the control box.
-Assemble the control box to the underside of the desktop at preferred
place with the screws incl.
-Use the intuitive control to adjust to preferred desk height.
Safety and warnings:
This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory
or mental capabilities or lack of
experience and knowledge if they have
been given supervision or instruction
concerning use of the appliance in a
safe way and understand the hazards
involved. Children shall not play with
the appliance. Cleaning and user
maintenance shall not be made
by children without supervision.
Correct Disposal of this product
This marking indicates that this product
should not be disposed with other household
wastes throughout the EU.
To prevent possible harm to the environment or
human health from uncontrolled waste
disposal, recycle it responsibly to promote
the sustainable reuse of material resources. To
return your used device, please use the return
and collection systems or contact the retailer
where the product was purchased.
They can take this product for environmentally
safe recycling.
RoHS
SUN-FLEX®DESKFRAME 600602
SUN-FLEX®DESKFRAME 600702
SUN-FLEX®DESKFRAME 600802
Electric control part:
Input voltage: 100-240V
Output voltage: 29V DC 3.0A
Duty cycle: 10% MAX 2 min on 18 min o
Switch power supply, low energy consumtion
Intuitive control
Desk frame part:
Built-in limit switch
Dynamic load: 80KG
Static load: 100KG
Load speed: 30mm/s
Lift range: 700mm---1160mm
Length of adjusting range:
700mm~1400mm
Installation of control box

EN
Installation instruction
HARDWARE INCLUDED
TOOLS REQUIRED
TOOLS INCLUDED
OR
M5 M4
Table top not
included
4
3
3
5
5
98
7
6
2
1
DQTY:10 BQTY:8 AQTY:10 CQTY:2
ST5.0*16
(optional)
M8*30 M4.2*16M6*12
M2.5
3(11)

EN
INSTALLATION INSTRUCTIONALLA CTION
STEP 1
STEP 2
A
M6*12
QTY:4
A
M6*12
QTY:2
4 (11)
1
2
3
3
M4
M5
LOOSEN
4
M4

EN
5 (11)
INSTALLATION INSTRUCTIONINSTALLATION INSTRUCTION
STEP 3
STEP 4
B QTY:8
M8*30
5
5
M5
DQTY:10
ST5.0*16
(optional)

EN
M5
TIGHTEN
STEP 5
STEP 6
INSTALLATION INSTRUCTION
TIGHTEN
M2.5
M2.5 LOOSEN
6
6(11)

CQTY:2
M4.2*16
98
7
STEP 7
STEP 8
INSTALLATION INSTRUCTION
7(11)

Advanced function settings
Limited height setting: Press ” ”and ” ”key for 5 seconds until you hear a buzz
sound. The limited height is set.
(Minimum limited height <96, maximum limited height >97).
Cancel function: run to the limit height, press ” ”and ” ”for 5 seconds, until you
hear the buzz sound. Limited height is cancelled.
Lock and unlock: Press ” ”and ”M4”key for 5 seconds, screen display ”LOC”,
system is now locked. Press ” ” and ”M4”key for 5 seconds, screen display ”LOC”
turns to a number, system is now unlocked.
S-
1
1
8
S-
2
S-
3
S-4
S-
5
S-6
S-8
1
8
1
8
0
1
S-
0
1
Press M4 key until you
hear the second ”beep”
sound (around 10s). Use
“↑”or “↓”key to select
Press "M4" key
Press ”M4”key
Press ”M4”key
0
1
0
0
7
Press ”M4”key
Press ”M4”key
Press ”M4”key
Press ”M4”key
Press ”M4”key
0
Switch metric and inches
Reservation function
Increase anti-collision
sensitivity (Current
detection)
reduce anti-collision
sensitivity (Current
detection)
Base height
Memory key operation
Overheat protection
Reservation function
Metric
Inches
Maximum sensitivity
Minimum sensitivity
Minimum sensitivity
Shut down
Shut down
Maximum sensitivity
Maximum sensitivity
Use”↑” or ”↓”to adjust base height
Press and hold to lower/raise the desk.
Keep your hands clear of the desk!
Press M4 to return to the numerical
display interface. Set up successful.
Set up multiple functions
Press ”M3”to return
Menu ”s- *”interface
Press to start, press again to stop.
Shut down
Turn on (continuous operation for two
minutes, error HOT)
1
2
3
4
5
6
7
8
0
DIRECTIONS FOR USE
8(9)

DIRECTIONS FOR USE
Display screen
Up & Down keys
Set key (M4)
Safety Function
Error code
E01, E06, E07 power error change power source
unplug and reinsert handset cable
rebound reminder, normal condition
change the controller
check the desktop
check the connecting cable
change motor
reduce the load
Stops. Automatic recovery after 20 minutes
handset error
anti-collision alert
controller error
desktop sloping
connection cable failure
motor error
overload
Overheating
E04
E05
E11
E14~E17
E08
E12
E18
HOT
Cause of error Solution
Handset shows error code and solution
Initialization
Memory keys M1/M2/M3/M4
The handset surface is a button panel. If no button is pressed within 30 seconds, the screen
auto-locks and corresponding M1/M2/M3/M4 keys are locked. Press Up or Down key to
re-activate the display screen.
Displays the height of the desk.
Press UP/DOWN key to adjust desk height until you reach optimal position.
Press the ”M4”key when internal parameters need to be set.
If something obstructs the desk’s upward or downward motion, the desk will stop mid-mo-tion.
1. When ”RST”appears on the screen, press the ”↓”button until the desk frame reaches its
lowest point. Initialization is complete when when the desk frame rebounds and the beep
sounds.
(Note! Hold the button down during the whole operation or the initialization will not be
completed successfully)
2. Forced initialization: Press the ”↓”button until the desk frame reaches its lowest point,
then release the button and press it again for about 5 seconds until you hear the beep and
the desk rises again. Initialization is complete.
3. Restore factory settings: When a new controller is used or the parameters need to be
restored to factory settings, press the ”↓”and ”↑” buttons simultaneously. You will hear the
rst beep after about 5 seconds and second beep sound after 10 seconds. When the display
screen shows "RST”, follow the operating instructions in item 1.
After setting the memory keys, the desk can automatically be raised to set memory height.
How to set memory mode
Hold down any of the M1/M2/M3/M4 keys for 5 seconds until you hear the“beep”sound.
The height is now memorized. Press the same button again and the desk moves to the set
height automatically.
Display screenUp & Down key Memory key Set key
9(11)

EN
10 (11)Rev. 20221207
EU Declaration of Conformity
1. Product model: 600602, 600702, 600802
2. Name and address of the manufacturer or his authorised representative:
Fridstiernan AB/SUN-FLEX
Logistikvägen 6
438 70 Landvetter, Sweden
3. This declaration of conformity is issued under the sole responsibility of the
manufacturer.
4. Object of the declaration:
Equipment: Height adjustable desk frame
Brand name: SUN-FLEX
Model/type: 600602, 600702, 600802
5. The object of the declaration described above is in conformity with the relevant
Union harmonization legislation:
Low Voltage Directive (LVD) 2014/35/EU
Electromagnetic Compatibility Directive (EMC) 2014/30/EU
Restriction of Hazardous Substances (RoHS) Directive 2011/65/EU
6. References to the relevant harmonised standards used or references to the other
technical specifications in relations to which conformity is declared:
LVD: EN 60335-2-2012
EN 60335-2-7:2010
EMC: EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
RoHS: EN 50581:2012
7. Signed for and on behalf of:
Landvetter 2022-12-05
Manufacturer Fridstiernan AB/SUN-FLEX
--------------------------------------------------------
Joakim Persson