Sunjoy L-DNC373PST-C-RED User manual

1
Warranty:
1. This swing must be assembled by two adults or more.
2. Tools are not included in packaging. The expected time required for
assembly is usually 1-2hours.
3. Before assembly, ensure all parts are present and not damaged.
4. Assemble on a flat, hard, and debris-free surface.
5. Keep canopy swing away from fire or inflammable objects.
6. There are small parts present in the packaging. Keep all small parts away
from children.
7. Children should be accompanied by an adult when using the swing.
8. Do not repack your swing until it is completely dry.
9. This swing must not be left erect in high wind conditions.
3-Seat Swing Assembly Instruction
Item# L-DNC373PST-C-RED

2
No. Part Qty. Image
8Handrail 2
9Seat 1
10
Canopy
side
support
2
11 Canopy
support 2
12 Canopy 1
13 Cushion 1
No. Part Qty. Image
1Top
support 1 1
2Top support
21
3 Front leg 2
4 Back leg 2
5Bottom
support 2
6Back support
11
7Back support
21
No. Part Qty. Image
A M6*90 Screw 4
B M6*85 Screw 2
C M6*68 Screw 4
D M6*63 Screw 6
E M6*50 Screw 4
F M6*45 Screw 2
No. Part Qty. Image
G M6*30 Screw 1
H screw arbor 2
I M6 Nut 23
J M6 Flat washer 23
K M6 Ball Nut 23
L Hook 2
Part List
Hardware List
J1
M6 Flat plastic washer 6
M SPANNER 1
N 1
SPANNER

3
Assembly
Fig.1: Insert the top support 1 (1) into the tube of the top support 2 (2) as the arrow direction by
using screw (F), flat washer (J), nut (I) and ball nut (K) to connect.
Fig.2: Using screw (A), flat washer (J), nut (I) and ball nut (K) to connect front leg (3) and
back leg (4) with top supports (1 and 2). Then using screw (B), flat washer (J), nut (I) and ball
nut (K) to connect front leg (3) with back leg (4).

4
Fig.3: Using screw (E), flat washer (J), nut (I) and ball nut (K) to connect bottom support (5)
with front leg (3) and back leg (4).
Fig.4: Insert the back support 1 (6) into the tube of back support 2 (7) by using screw (G), flat
washer (J), nut (I) and ball nut (K) to connect the back supports (6 and 7).

5
Fig.5: Using screw (C), flat washer (J), nut (I) and ball nut (K) to connect assembled
back supports (6 and 7) with back leg (4).
Fig.6: Using screw (D), flat washer (J), nut (I) and ball nut (K) to connect handrail (8) with
seat (9).
1

6
Fig.7: Using screw (D), flat washer (J), nut (I and ball nut (K) to connect the bottom end of
the handrail (8) with bottom end of the seat (9).
Fig.8: Attach one end of the hook (L) to the handrail (8) and other end to the rings on the top
supports (1 and 2).
11

7
Fig.9: Using screw arbor (H) to connect canopy side support (10) with top supports (1 and 2).
Fig.10: Insert the canopy support (11) into the canopy (12) as the arrow direction.

8
Fig.11: Insert the canopy support (11) into the canopy side support (10) as the arrow
direction, then attach the canopy (12).
Fig.12: Place the cushion (13) on the seat (9).