Sunjoy Tete-a-Tete L-DN919SAL User manual

Assembly Instructions
Tête-à-Tête Bistro Set
Item# L-DN919SAL
Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start to finish. The final
product will be a quality piece that will go together smoothly and give years of enjoyment.
CAUTION!
Read and follow all Safety Statements, Warnings, Assembly Instructions and Use & Care directions before
attempting to assemble.
Repeated assembly can weaken the locking ability of the washers. Periodically check all bolted connections on
your furniture to make sure they are tight and secure. Retain these instructions for future reference.
Do NOT over tighten any of the nuts as this may DAMAGE the threads. Tighten each nut firmly and properly.
Some parts may contain sharp edges. Wear protective gloves as necessary.
Handle carefully when moving as the unit is very heavy
IMPORTANT:
Repeated assembly can weaken the locking ability of the washers. Periodically check all bolted connections on
your furniture to make sure they are tight and secure. Retain these instructions for future reference
CARE AND MAINTENANCE:
Before using, clean the product completely with a soft, dry towel.
When not in use, wipe free of any dirt or loose objects, wash with a mild solution of soap and water; rinse
thoroughly and dry completely. Do not use strong detergent or abrasive cleaners.
When not in use, store the product in a cool, dry location away from sunlight.

No. Description Quantity Image
A Left armrest 1
B Right armrest 1
C Left leg 1
D Right leg 1
E Seat 2
F Middle support bar 2
G Back support bar 2
H Table top 1
I Glass top 1
J Slate shelf 1
K Magazine rack 1
L Handle (preassembled on K) 1
M Connector (preassembled on F) 4
N Seat cushion 2
O Backrest cushion 2
Parts List

No. Description Q’TY Image
AA 1/4"-20*0.75 bolt 12
BB 1/4"-20*0.6 bolt 4
CC 1/4”-20*1 bolt 4
DD Ф1/4" flat washer 22
EE Ф1/4" spring washer 22
FF M4*14mm bolt
(preassembled) 2
GG 5/16"-18*1.6 bolt 8
HH 5/16"-18*2" bolt
(preassembled on F) 8
II 5/16"-18 nut
(8pcs preassembled) 16
JJ
Ф5/16" flat washer
(8pcs preassembled) 16
KK
Ф5/16" spring washer
(8pcs preassembled) 16
LL
∮8*14mm Foot pad
(preassembled) 8
MM 1/4” Hex key 1
NN 50*25*3mm Large washer
(8pcs preassembled) 16
OO Alum. umbrella hole cap 1
PP Plastic umbrella hole cap
(preassembled with glass top) 1
QQ Stopper ∮15*16mm 2
RR Plastic sucker
( Preassembled ) 8
SS Wrench 5/16" 2
TT 1/4"-20*1.6" bolt 2
Hardware List

Step 1: Connect Slate shelf (J) and Left leg (C) with flat
washer (DD), spring washer (EE) and bolt (CC).
Connect Right leg (D) and Slate shelf (H) in the same
way. Please do not fix the bolts tightly here.
Step 2: Connect Table top (H) and Left leg (C) with
flat washer (DD), spring washer (EE) and bolt (AA).
Connect Right leg (D) and Table top (H) in the same
way. Please do not fix the bolts tightly here.
Step 3: Connect the Magazine rack (K) & Left leg (C) with bolt
(TT), spring washer (EE), flat washer (DD), and the Stopper (QQ)
as illustration. Connect the Magazine rack (K) & Right leg (D) in
the same way. Please do not tighten the bolts fully otherwise
you may not open the magazine rack easily.
Step 4: Insert Back support bar (G) into the connect hole of Left
leg (C) & Left armrest (A), connect them with flat washer (DD) ,
spring washer (EE) and bolt (BB). Connect Right armrest (B) &
Right leg (D) in the same way. Please do not fix the bolts tightly
here.

Step 5: Fit Middle support bar (F) to the Left armrest (A) & Left leg (C), connect them with Flat washer (DD),
Spring washer (EE) and Bolt (BB). Connect the Right armrest (B) & Right leg (D) in the same way. Please do not
fix the bolts tightly here.
Step 6: Using Bolt (GG) through spring washer (KK), flat washer (JJ), the connect hole of Large washer (NN),
Seat (E) , Connector (L) (preassembled), Lager washer (NN) orderly, and fix them with Nut (II). Assemble the
other side Seat (E) in the same way. Fix all of the bolts tightly.

Now, your Tête-à-Tête bistro is ready to use.
Step 7: Put Cap (OO) onto the hole of the Slate shelf (J). Put Glass top (I) onto the Table top (H).
Step 8: Put the Seat cushion (N) & Backrest cushion (O) on the Seat (E) then position Velcro tabs to secure cushion
and close.

Service:
Please do not return this product to the store. For technical assistance on assembly or replacement parts call
Sunjoy Industries at 1(866) 578-6569 from 8:30 AM to 5:30 PM EST or Email [email protected] or visit
www.sunjoygroup.com to place your order or fax your parts replacement order form together with your purchase
receipt to 1 [phone] for assistance.
Limited Warranty:
This limited warranty is extended to the original purchaser and applies to defects in materials and workmanship of
your item, provided the item is maintained with care and used only for personal, residential purposes.
The item is warranted to be free from defects in material or workmanship for a period of 7 years on frame and 2
years on fabric. However, the warranty does not cover transportation or delivery costs, or compensate the
individual or any outside party for assembling or disassembling the product. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.
Exclusions:
Items used for commercial, contract, or other non-residential purposes, or items damaged due to acts of nature,
vandalism, misuse, or improper assembly are not covered. Corrosion or rusting of hardware is not covered. Proof
of purchase (dated register receipt) is required for warranty claims. Warranty is to the original purchaser and is
non-transferable. Any replacement of warranted items will be in the original style and color, or a similar style and
color if the original is unavailable or has been discontinued. As some states do not allow exclusions or limitations
on an implied warranty, the above exclusions and limitations may not apply. This warranty gives you specific rights,
and you may also have other rights, which vary from state to state.
Made in China