Sunjoy L-GZ761PST User manual

Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start to finish.
All you will need is a hammer and ladder (not included) whose height is no less than 2.5m.
Item Identification: For ease of identification, all parts are labeled to correspond to the Step number in
which the part is used.
PRECAUTIONS:
Do not cook underneath canopy.
Do not ignite fireworks underneath canopy.
Do not bleach canopy to clean.
Do not dry clean.
Do not wash in washing machine or dry in dryer.
Lower and secure side panels if open in stormy conditions.
Be certain to brush snow off cover in winter
This is a temporary structure and is not recommended as a permanent structure.
Assembly Instructions
10'x20' Shelter
Item: L-GZ761PST

3-way corners
for horizontal bar A 6
4-way corners
for horizontal bar B 6
Post (1) C 8
Horizontal bar D 9
Incline bar E 8
Post (2) F 8
Post base G 16
Screw cap H 8
Top canopy I 1
Short side panel J 2
Stake K 48
Peg L 8
Parts List

Frame Assembly Layout
Hardware Pack 1
Flat washer M8 AA 12
Nut M8 BB 16
Bolt M8*60 CC 16
Elastic ball strap DD 46
Rope L=3000mm EE 8
Wrench M8 FF 2
1. Incline bar (E)
2. Horizontal bar (D)
3. 4-way corners (B)
4. 3-way corners (A)

Frame Assembly
Each bar (E, D) has a spring-activated button for locking into the corner pieces. Insert Incline bar (E) and
Horizontal bar (D) into corners (A, B) as shown below and the spring-activated button will lock into the
corner pieces.
Top Canopy Assembly
Spread the top canopy (I) over the inclined frame as shown below.
Stand the support bar of the vents as shown below

Short side panel Assembly
Tie the short side panel (J) to the incline bar (E) with the elastic ball strap (DD) as shown below.
Insert the strap through the grommet on the canopy. Wrap the strap around the bar and then around the ball to
lock the ball in place, as shown in Fig.1 & Fig.2.

Post (1) Assembly
Each post (1) has a spring-activated button for locking into the corner pieces. Insert post 1 (C) to post
base (G) and tighten with bolt (CC), flat washer (AA) and nut (BB). There are two optional holes on the
bottom of the posts. Level the frame by choosing the proper holes in the posts. Insert the shrinkage end
of post (1) to corners, and tighten with spring-activated button.
Roll up long side panel
Roll up both of long side panels to the horizontal bar (D) with the elastic ball strap (DD) as shown below.

IMPORTANT:
1. When assembling and using this product, basic safety precautions should always be followed to reduce
the risk of personal injury and damage to equipment. Please read all instructions before assembly and use.
2. Some parts may contain sharp edges, wear protective gloves if necessary. At least four or more people
are recommended for safe assembly.
3. Keep all children and pets away from assembly area.
4. At least 6 feet from any obstruction such as fence, garage, house, overhanging branches, laundry line or
electrical wires.
5. Do not use the unit during an electrical storm, as there is a remote chance of getting struck by lightening.
6. The fabric roof should be removed for the winter in areas subject to heavy snowfall. A fabric roof could
accumulate a lot of snow/weight which genuinely could be an issue. Remove fabric roof and panels to poles,
when there is a risk of high wind, as possible damage will occur to the structure.
7. Install on level surface.
8. Never barbecue under this gazebo or use lanterns that have open flames.
9. This package contains small items and plastic bags that should be kept away from children.
10. Check all nuts and bolts for tightness before and during usage. Ensure that all connectors and poles are
firmly secured in position fully. It is important to do so before use so as to avoid a possible collapse or
damage to the item, which could also result in injury.
Post
(
2
)
A
ssembl
y
Insert post 2 (F) to post base (G) and tighten with bolt (CC), flat washer (AA) and nut (BB). Insert stake (K) to
post base (G), then attach the side panel of top canopy (I) and the assembled end of rope (EE) to the screw of
top post (2) and fix them by screw cap (H). Finally, attach the other end of the rope to peg (L), and fix it on the
lawn as shown below.

WARNINGS:
1. Assembly Instructions must be followed.
2. Pegs & ropes supplied must be used to hold this gazebo in place when upright.
3. Warranty does not cover damage due to extreme weather conditions.
WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC.
This tent meets the flammability requirements of CPAI-84. The fabric may burn if left in continuous contact
with any flame source. The application of any foreign substance to the tent fabric may render the
flame-resistant properties ineffective.
This unit is heavy. Do not assemble this item alone.
LIMITED WARRANTY:
This limited warranty is extended to the original purchaser and applies to defects in materials and
workmanship of your item provided the item is maintained with care and used only for personal, residential
purposes.
The item is warranted to be free from defects in material or workmanship for a period of 1 year. If any defect
is found, please call our customer service department at 1-866-578-6569 for help. The manufacturer will not
cover transportation or delivery costs, or compensate the individual or any outside party for assembling or
disassembling the product. This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
Made in China
Important: For technical assistance on assembly or replacement parts, please call Sunjoy Industries at
1(866) 578-6569 from 8:00 AM EST to 8:00 PM PST or email to customer[email protected] or visit
www.sunjoyonline.com to place your order or fax your parts replacement order form together with your
purchase receipt to 1-740-283-3549 for assistance.