Sunjoy L-GZ120PST-2 User manual

Assembly Instructions
Item# L-GZ120PST-2
Thank you for your purchase!
Caution: Carefully Read Instructions and Procedures for Safe
Operation.
Important: Please do not return this product to the store. For technical assistance on
assembly or replacement parts. Please call Sunjoy Industries at 1-866-578-6569 from 8:00
am EST to 8:00 pm PST or fax the replacement part form which is in the box to
1-740-283-3549 or Email [email protected] for assistance.

Safety Information
WARNING
When assembling and using this product, basic safety precautions should always be followed
to reduce the risk of personal injury and damage to equipment. Please read all instructions
before assembly and use.
Some parts may contain sharp edges, wear protective gloves if necessary. At least three or
more people are recommended for safe assembly.
Keep all children and pets away from assembly area.
Begin assembly not less than 6 feet from any obstruction such as fence, garage, house,
overhanging branches, laundry line or electrical wires.
Install on level ground. This gazebo cannot be permanently staked or attached to concrete
floor or platform. The provided stakes are for soft ground use only. If assembling on a hard
surface like a deck or concrete, other forms of attachment must be used such as expansion
bolts that can be purchased locally.
This gazebo is intended for decorative and sunshade purposes only and is not meant to
withstand inclement weather including high winds, rain and snow. Gazebo fabric is water
resistant, not water proof and may leak during exposure to precipitation.
Please lay out all parts before assembling, checking to make sure all parts are there. If any
parts are missing, please call 1-866-578-6569 and parts will be expedited to you.
KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC. This Tent
meets the flammability requirements of CPAI - 84. The fabric may burn if left in continuous
contact with any flame source. The application of any foreign substance to the tent fabric may
render the flame-resistant properties ineffective.
Warranty
1 YEAR WARRANTY FOR FRAME AND FINISH
Limited Warranty
The item is warranted to be free from defects in material or workmanship for a period of 1 year.
However, we don't reimburse for transportation or delivery costs, or compensate the individual or any
outside party for assembling or disassembling the product. This limited warranty is extended to the
original purchaser and applies to defects in materials and workmanship of your item, provided the item
is maintained with care and used only for personal, residential purposes.

Exclusions:
It remains the customer's responsibility for freight and packaging charges to and from our service
center. Items used for commercial, contract, or other non-residential purposes, or items damaged due
to acts of nature, vandalism, misuse, or improper assembly are not covered. Corrosion or rusting of
hardware is not covered. Proof of purchase (dated register receipt) is required for warranty claims.
Warranty is to the original purchaser and is non-transferable. Any replacement of warranted items will
be in the original style and color, or a similar style and color if the original is unavailable or has been
discontinued. As some states do not allow exclusions or limitations on an implied warranty, the above
exclusions and limitations may not apply. This warranty gives you specific rights, and you may also
have other rights, which vary from state to state.
Care and Maintenance
It is advised that the Canopy should be removed in the winter for best protection and length of use. Our
steel components for garden accessories and furniture are treated with rust inhibiting paint that
protects them from rusting. However, due to the nature of steel, surface oxidation (rusting) will occur
once these protective coatings are scratched. This is a natural process and is not a defect! To
minimize this condition, we recommend care when assembling & handling the product to prevent
scratching the paint. Should any scratching or damage occur, it is strongly recommended that
consumers buy touch up paint prior to the assembly process so that any parts they scratch during
assembly are touched up. Surface rust can also be easily removed with a very light application of
common cooking oil. If surface oxidation (rusting) occurs and if no measure is taken to prevent this, the
oxidation may start dripping on to deck or patio and cause damaging stains, which may be difficult to
remove. This can be prevented if the measure is taken to keep the product from oxidizing. Also the use
of wax candle to lubricate the zippers once a year will keep them running smoothly.
Pre-Assembly
PLANNING ASSEMBLY
To prevent damage, place all parts on a soft surface during assembly.
Remove all protective caps before beginning assembly. It takes about
30 minutes for four persons to complete all the assembly
HARDWARE INCLUDED
Part Description QTY. Image
DD ￠6*180 Stake 12 PCS
EE Hook 48 PCS

Package contents
NO. IMAGE DESCRIPTION QTY.
A
Screen 4
B Screen for long side 2
C Screen for short side 2
D Big Top Connector 1
E Support Pole 4
F
Support Pole1 4
G Support Pole 2 4
H
Arch beam 1 2
I Arch beam 2 2
J Hook 1
K Big canopy 1
L
Small canopy 1
M
Mosquito netting 1

Assembly Instructions
``

Fig.1: Insert the Screen (B) and Screen (C) into the hole of screen, then the
Screen (B) and Screen (C) with rotating the sealed strip on the Screen.
Fig.2: Attach and fix the Hook (J) to Big Top Connector (D).
Fig.3: Assemble the Support Pole (E) and Big Top Connector (D).Please note
that the Support Pole (E) should be inserted into the longer tubes.
Fig.4: Insert Support Pole 1(F) and Support Pole 2 (G) into the Support Pole (E).
Support Pole 1 (F) should be assembled near to Short Beam (C), Support Pole 2 (G) is
opposite.
Fig.5: Connect Support Pole 1 (F) and Support Pole 2 (G) to Screen (A), please note
the direction when assembling. Support Pole 1 (F) should be connected with Screen
for long side (C), Support Pole 2 (G) should be connected with Screen for Long Side
(B).
Fig.6：Insert Arch Beam 1 (H) and Arch Beam 2 (I) into Big Top Connector (D), please
note the direction when assembling, Arch Beam 1 (H) should be connected with
Screen for Short Side (C), Arch Beam 2 (I) should be connected with Screen for Long
Side (D).
Fig.7：Insert the lower part of Arch beam 1 (H) and Arch Beam 2 (I) into the
Screen for Long Side (B) and Screen For Short Side (C), please note that Arch
beam 1 (H) should be connected with Screen For Short Side (C), Arch Beam 2
(I) should be connected with Screen For Long Side (B).

Fig.8: Put the Big Canopy (K) onto the Frame first, but don’t spread it
completely.
Fig.9: Assemble the Small Canopy (L), fix the Mosquito Netting of Small
Canopy and tie of Big Canopy together. Spread the Big Canopy (K)
completely and fix it into Beam and Screen.
Made in China
2016-6
Fig.10: Connect the Mosquito Netting to Big Screen (A), Right Screen (B) and
Left Screen(C) with the Hook (EE), please note the long and short side of the
Mosquito Netting and Frame when assembling.
Fig.11: Attach the Gazebo to ground with Stake (DD).