Sunny Health & Fitness P8400 User manual

0
PINK MAGNETIC RECUMBENT BIKE
P8400
USER MANUAL
IMPORTANT! Please retain owner’s manual for maintenance and adjustment instructions. Your
satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE CONTACTED
US: [email protected] or 1- 877 - 90SUNNY (877-907-8669).

1
IMPORTANT SAFETY INFORMATION
We thank you for choosing our product. To ensure your safety and health, please use this equipment
correctly. It is important to read this entire manual before assembling and using the equipment. Safe
and effective use can only be achieved if the equipment is assembled, maintained and used properly.
It is your responsibility to ensure that all users of the equipment are informed of all warnings and
precautions.
1. Before starting any exercise program, you should consult your physician to determine if you have
any medical or physical conditions that could put your health and safety at risk, or prevent you
from using the equipment properly. Your physician’s advice is essential if you are taking
medication that affects your heart rate, blood pressure or cholesterol level.
2. Be aware of your body’s signals. Incorrect or excessive exercise can damage your health. Stop
exercising if you experience any of the following symptoms: pain, tightness in your chest, irregular
heartbeat, shortness of breath, lightheadedness, dizziness or feelings of nausea. If you do
experience any of these conditions, you should consult your physician before continuing with your
exercise program.
3. Keep children and pets away from the equipment. The equipment is designed for adult use only.
4. Use the equipment on a solid, flat level surface with a protective cover for your floor or carpet. To
ensure safety, the equipment should have at least 2 feet (60CM) of free space all around it.
5. Ensure that all nuts and bolts are securely tightened before using the equipment. The safety of the
equipment can only be maintained if it is regularly examined for damage and/or wear and tear.
6. Always use the equipment as indicated. If you find any defective components while assembling or
checking the equipment, or if you hear any unusual noises coming from the equipment during
exercise, discontinue use of the equipment immediately and do not use until the problem has
been rectified.
7. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that may become
entangled in the equipment.
8. Do not place fingers or objects into the moving parts of the equipment.
9. The maximum weight capacity of this unit is 220 pounds (100 KG).
10. The equipment is not suitable for therapeutic use.
11. To avoid bodily injury and/or damage to the product or property, proper lifting and moving is
required.
12. Your product is intended for use in cool, dry conditions. You should avoid storage in extreme cold,
hot or damp areas as this may lead to corrosion and other related problems.
13. This equipment is designed for indoor and home use only, it is not intended for commercial use!

2
EXPLODED DIAGRAM 1

3
EXPLODED DIAGRAM 2
90
89
65 64
68
91
91
91
91
HARDWARE PACKAGE
#16 M10*60 4PCS
#19 d10*Φ25*2*R30 4PCS
#37 M8*60 1PC
#7 d8*Φ20*2*R30 4PCS
#8 M8*16 5PCS
#32 d8*Φ16*1.5 2PCS
#20 M10 4PCS
#38 d8 2PCS
#31 M8 1PC
#22 M16*1.5*27 1PC
#46 S17-19
#45 S13-14-15
#44 S6

4
Ordering Replacement Parts (U.S. and Canadian Customers only)
Please provide the following information in order for us to accurately identify the part(s) needed:
✓The model number (found on cover of manual)
✓The product name (found on cover of manual)
✓The part number found on the “EXPLODED DIAGRAM” and “PARTS LIST” (found near the front of
the manual)
Please contact us at [email protected] or 1- 877 - 90SUNNY (877-907-8669).
No.
Description
Spec.
Qty.
No.
Description
Spec.
Qty.
1
Computer
1
46
Spanner
S17-19
1
1a
Computer Wire
1
47
Fixing Plate
t1.5*56*72
2
2
Screw
M5*15
1
48
Screw
M6*10*Φ12
5
3
Arc-Washer
d5*Φ20*1*R30
1
49
Washer
d 6*Φ16*1.5
3
4
Foam Grip
Φ23*5*120
2
50
Bolt
M6*12*S10
3
5
Handlebar Post
1
51
Screw
M6*8*Φ12
1
6
End Cap
Φ25*16
4
52
Inertial Axle
1
7
Arc Washer
d8*Φ20*2*R30
4
53
Idler Connecting Rod
1
8
Screw
M8*16
17
54
Spring
Φ2*Φ12*60*N20
1
9
Sensor Wire A
1
55
Nut
M8*H7.5*S13
1
10
Sensor Wire B
1
56
Bearing
6001-2RS CXSH
2
11
Tension Control Cable
1
57
Idler Wheel
1
12
Sensor Wire C
1
58
Screw
1
13
Tension Hook
1
59
Washer
D12*Φ17*0.5
1
14
Sensor Wire D
1
60L/R
Crank Cap
2
15
End Cap
Φ50
4
61
Screw
ST4.2*19*Φ8
6
16
Bolt
M10*60
4
62L/R
Chain Cover
2
17
Front Stabilizer
1
63
Thin Nut
1
18L/R
Pedal L/R
2
64
Washer
D26*Φ38*1
1
19
Arc Washer
d10*Φ25*2*R30
4
65
Washer
1
20
Nut
M10
4
66
Bearing Housing
2
21
Main Frame
1
67
Ball Bearing
2
22
Knob
M16*1.5*27
1
68
Cap
1
23
Bushing
Φ50
1
69
Nut
M6*H5*S10
2
24
Sensor Wire E
1
70
Bolt
M6*45*S10
1
25
Rear Main Frame
1
71
Sensor Seat
1
26
End Cap
Φ50
2
72
Screw
ST4.2*10*Φ8
1
27
Rear Stabilizer
1
73
Crank with Belt Wheel
1
28
Screw
ST4*19
2
74
Round Magnet
1
29
Foam Grip
Φ23*5*500
2
75
Belt
1
30
Handle Pulse Wire
1
76
Square Magnet
40*25*10
4
31
Nut
M8
1
77
Magnet Locator
1
32
Washer
d8*Φ16*1.5
14
78
Magnetic Board
1
33
Grommet
Φ12*Φ11*3
3
79
Spring
Φ1.5*Φ15*41*N8
1
34
Handlebar
1
80
Bolt
M6*16*S10
2
35
Handle Pulse Wire
2
81
Spring Washer
D6
2
36
End Cap
F38*38*1.5
2
82
Washer
D6*Φ12*1.2
2
37
Bolt
M8*60
1
83
C Clip
D12
2
38
Spring Washer
d8
6
84
Axle for Magnetic Board
1
39
Backrest Frame
1
85
Screw
ST3*10*Φ5.6
5
40
Seat Cushion
1
86
Inertial Wheel
1
41
Backrest Cushion
1
87
Bearing Seat
2
42
Screw
M5*10
2
88
Bearing
6001-2RS C&U
2
43
Washer
d6*Φ12*1
2
89
Washer
1
44
Allen Wrench
S6
1
90
Nut
1
45
Spanner
S13-14-15
1
91
Screw
ST4.2*20
4
PARTS LIST

5
ASSEMBLY INSTRUCTIONS
STEP 1:
Secure Front Stabilizer (No. 17) to Main
Frame (No. 21) with 2 Bolts (No. 16), 2 Arc
Washers (No. 19) and 2 Nuts (No. 20).
STEP 2:
Connect Sensor Wire A (No. 9) with Sensor
Wire C (No. 12). Then connect Sensor Wire B
(No. 10) with Sensor Wire D (No. 14). (See
diagram a to the left)
NOTE: Turn the Tension Control Cable (No. 11)
all the way to the left (the lowest level of
resistance). This provides the tension cable with
the longest length required to connect it. (See
diagram c)
Connect Tension Hook (No. 13) with Tension
Control Cable (No. 11). (See diagram b to the
left)
Secure Handlebar Post (No. 5) to Main Frame
(No. 21) with 4 Screws (No. 8) and 4 Arc
Washers (No. 7).
#16 M10*60 2PCS
#19d10*Φ25*2*R30 2PCS
#46S17-19
#20M10 2PCS
#8 M8*16 4PCS
#7d8*Φ20*2*R30 4PCS
#44 S6
a
b
C

6
a
a
STEP 3:
Remove 2 preassembled Screws (No. 42) from
the back of the computer. Connect Computer
Wire (No. 1a) with Sensor Wire A (No. 9), then
secure Computer (No. 1) to Handlebar Post
(No. 5) with 2 Screws (No. 42). Insert Sensor
Wire B (No. 10) into the back of Computer (No.
1).
Secure Pedal (No. 18L/R) onto the left and right
crank of Main Frame (No. 21).
CAUTION: The left side of the machine has
reversed threading. You must screw the left
pedal counter-clockwise to tighten. The right
pedal is tightened by turning clockwise. Failure
to follow these instructions can result in
permanent damage to your bike.
STEP 4:
Secure the Rear Stabilizer (No. 27) to the Rear
Main Frame (No. 25), with 2 Bolts (No. 16), 2
Arc Washers (No. 19) and 2 Nuts (No. 20).
Secure Backrest Frame (No. 39) to Rear Main
Frame (No. 25) with 4 Screws (No. 8), 4 Spring
Washers (No. 38) and 4 Washers (No. 32).
For easier installation of next step, try flipping
Rear Main Frame (No. 25) over.
Parts No. 8, 38,32 are preassembled on Rear
Main Frame (No. 25). Simply unscrew and
reattach with the Backrest Frame (No. 39).
Secure Seat Cushion (No. 40) and Backrest
Cushion (No. 41) to Backrest Frame (No. 39)
with 8 Screws (No. 8) and 8 Washers (No. 32).
Part No. 8 & 32 are preassembled on Seat
Cushion (No. 40) and Backrest Cushion (No.
41).
#42 M5*10 2PCS
#45S13-14-15
#16 M10*60 2PCS
#19d10*Φ25*2*R30 2PCS
#20M10 2PCS
#8M8*16 12PCS
#32 d8*Φ16*1.5 12PCS
#38d8 4PCS
#46S17-19
#44 S6

7
STEP 5:
Connect Sensor Wire D (No. 14) with Sensor
Wire E (No. 24), then secure the Rear Main
Frame (No. 25) to the Main Frame (No. 21) with
the Knob (No. 22).
NOTE: There are different holes on the Rear
Main Frame (No. 25) which can be used for
people with different height. You can find the best
position hole for your height. With feet at the
extended position, your knee should bend at 15
degrees.
STEP 6:
Secure Handlebar (No. 34) to Backrest Frame
(No. 39) with 1 Bolt (No. 37), 1 Screw (No. 8), 2
Spring Washers (No. 38), 2 Washers (No. 32)
and 1 Nut (No. 31).
Connect Sensor Wire E (No. 24) with Handle
Pulse Wire (No. 30).
Assembly is complete.
#22 M16*1.5*27 1PC
#37 M8*60 1PC
#32 d8*Φ16*1.5 2PCS
#31M8 1PC
#8M8*16 1PC
#38d8 2PCS
#44 S6
#45S13-14-15

8
EXERCISE COMPUTER
FUNCTION BUTTONS:
MODE: Press to select functions.
Press and hold the MODE button for 3
seconds to reset time, distance and calories.
SET: (If Available) Press to set values of time, pulse, distance and calories when not in scan mode.
Press the MODE button to cycle through functions: time, distance and calories to select desired
function.
Use the SET button to set a value for time, distance or calories. The value of a function will be set on
a countdown.
Press the MODE button once more, to save the function value you’ve created.
RESET: (If Available) Press to reset time, pulse, distance and calories to zero when not in scan mode.
OPERATION FUNCTIONS:
SCAN: Press MODE button until “▼” appears at SCAN position (or until “SCAN” appears), the
computer will rotate through all 5 functions: Time, Speed, Distance, Calories and Total Distance.
Each display will be held for 6 seconds.
TIME: Counts the total time of the exercise from start to finish.
SPEED: Displays the current speed.
DISTANCE (DIST): Counts the distance of an exercise from start to finish.
CALORIES (CAL): Counts the amount of total calories burned during an exercise from start to finish.
TOTAL DISTANCE (ODO): Counts the total distance after installing the batteries.
AUTO ON/OFF & AUTO START/STOP: If the wheel is in motion or if any button is pressed, the
computer will become active and shall remain active until it’s been inactive for 8 minutes. Then the
power (computer) will turn off automatically.
PULSE RATE: Press MODE button until “▼” appears at PULSE position, (or until “ ” appears). To
properly measure your pulse rate, you must place both your palms on the contact pads located on the
handlebar next to the seat.
Remark: During the process of “pulse measurement”, due to the contact jamming, the measurement
value may be higher than virtual pulse rate during the first 2~3 seconds, after which it will return to
normal level. To ensure testing accuracy, it is suggested that user test pulse during stop/pause
exercise to avoid any possible influence. The measurement value cannot be regarded as the basis of
medical treatment.
ALARM: The functions of time, distance and calorie can be set to countdown, if any of the above
value goes to zero, the computer will beep for 15 seconds.

9
Press MODE to select the function, then press SET to adjust the value.
SPECIFICATIONS
BATTERY REPLACEMENT
The batteries are located on the back of the computer. To replace the batteries, open the battery
cover. Remove the batteries. Replace with new batteries. Make sure the (-) end of the battery goes to
the spring end in the battery compartment. Put the cover back.
When changing batteries, always change both with new batteries. Do not mix old and new batteries.
BATTERY DISPOSAL
Dispose the batteries according to the laws and regulations of your local region. Some batteries may
be recycled. When disposing or recycling, do not mix battery types.
FUNCTION
Auto Scan
Every 6 seconds
Running Time
00:00 ~ 99:59(Minute: Second)
Current Speed
The max pick-up signal is 999.9 MILE/H (or
9999RPM)
Trip Distance
0.0 ~ 999.9 MILE
Calories
0 ~ 9999 Kcal
Total Distance
0 ~ 9999 MILE
Pulse Rate
40-240BPM
Battery Type
2 pcs of SIZE- AAA
Operating Temperature
0℃~ +40℃(32℉~104℉)
Storage Temperature
-10℃~ +60℃(14℉~140℉)
Version 1.7