Sunny Health & Fitness P8300 User manual

0
PINK MAGNETIC ELLIPTICAL BIKE
P8300
USER MANUAL
IMPORTANT! Please retain owner’s manual for maintenance and adjustment instructions. Your
satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE
CONTACTED US: supp[email protected] or 1- 877 - 90SUNNY (877-907-8669).

1
IMPORTANT SAFETY INFORMATION
We thank you for choosing our product. To ensure your safety and health, please use this
equipment correctly. It is important to read this entire manual before assembling and using the
equipment. Safe and effective use can only be achieved if the equipment is assembled, maintained,
and used properly. It is your responsibility to ensure that all users of the equipment are informed of
all warnings and precautions.
1. Before starting any exercise program, you should consult your physician to determine if you
have any medical or physical conditions that could put your health and safety at risk or prevent
you from using the equipment properly. Your physician’s advice is essential if you are taking
medication that affects your heart rate, blood pressure, or cholesterol level.
2. Be aware of your body’s signals. Incorrect or excessive exercise can damage your health. Stop
exercising if you experience any of the following symptoms: pain, tightness in your chest,
irregular heartbeat, shortness of breath, lightheadedness, dizziness, or feelings of nausea. If
you do experience any of these conditions, you should consult your physician before continuing
with your exercise program.
3. Keep children and pets away from the equipment. The equipment is designed for adult use only.
4. Use the equipment on a solid, flat level surface with a protective cover for your floor or carpet.
To ensure safety, the equipment should have at least 2 feet (60 CM) of free space all around it.
5. Ensure that all nuts and bolts are securely tightened before using the equipment. The safety of
the equipment can only be maintained if it is regularly examined for damage and/or wear and
tear.
6. Always use the equipment as indicated. If you find any defective components while assembling
or checking the equipment, or if you hear any unusual noises coming from the equipment during
exercise, discontinue use of the equipment immediately and do not use until the problem has
been rectified.
7. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that may
become entangled in the equipment.
8. Do not place fingers or objects into the moving parts of the equipment.
9. The maximum weight capacity of this unit is 220 pounds (100 KG).
10.The equipment is not suitable for therapeutic use.
11.To avoid bodily injury and/or damage to the product or property, proper lifting and moving are
required.
12.Your product is intended for use in cool and dry conditions. You should avoid storage in extreme
cold, hot or damp areas as this may lead to corrosion and other related problems.
13.This equipment is designed for indoor and home use only; it is not intended for commercial use.

2
EXPLODED DIAGRAM
13L
13R
12
12
35a

3
PARTS LIST
No.
Description
Spec.
Qty.
No.
Description
Spec.
Qty.
1
Main Frame
1
32
Alloy Bushing
Φ14*Φ10.1*10
4
2
Rear Stabilizer
Φ50
1
33
Bushing
Φ28.5*Φ15.5*23
2
3
Adjust Adjustable End
Cap
Φ50
2
34
Bushing with
Chamfer
Φ28.5*Φ15.5*23
2
4
Carriage Bolt
M10*60
4
35
Tension Control
Knob
8-level
1
5
Arc Washer
d10*Φ25*2*R3
0
4
35a
Tension Control
Wire
1
6
Nut
M10
4
36
Handlebar Post
1
7
Front Stabilizer
Φ50 w/ wheel
1
37
Bushing
Φ32*1.5
2
8
End Cap
Φ50 wheel
2
38
Knob
M8*36
2
9
Ball Cap
S16
2
39
Screw
M5*20
1
10
Bolt
M10*50
2
40
Arc Washer
d5*Φ20*1.5
1
11L/R
Hinge Bolt L/R
2
41
Screw
M5*10
2
12
Alloy Bushing
Φ24*Φ16.1*20
8
42
Spring Washer
d13
2
13L/R
Link Connector
Combination
L/R
2
43
Computer
1
14
Washer
d10*Φ20*2
6
43a
Computer Wire
1
15
Nylon Nut
M10
6
44
End Cap
Φ28*1.5
2
16
Washer
d13*Φ26*2
4
45
Foam Grip
2
17L/R
Nylon Nut L/R
B0.5
2
46L/R
Handlebar L/R
2
18
Ball Cap
S18
6
47
Allen Wrench
S6
1
19
End Cap
J40*25*1.5
2
48
Allen Wrench
S8
1
20
Bolt
M10*45
4
49
Wave Washer
d17*Φ25* 0.3
4
21L/R
Pedal L/R
2
50
Spanner
S13-14-15
1
22L/R
Connecting Rod
L/R
2
51
Spanner
S17-19
1
23
End Cap
Φ32*1.5
2
52
Tension Control
Wire
1
24L/R
Swing Rod L/R
2
53
Hex Nut
M6
2
25
Arc Washer
d8*Φ20*2*R30
4
54
Bolt
4
26
Screw
M8*16
4
55
Flat Washer
Φ6.5*Φ16*1.5
3
27
Sensor Wire
1
56
Bearing
6001RS C&U
4
28
Trunk Wire
1
57
Bearing Seat
D type
2
29
Tension Wire
1
58
External
Magnetic
Flywheel
1
30
Ball Cap
S13
2
59
Inertia Wheel
1
31
Nylon Nut
R B0.5
4
60
Bearing Baffle
2

4
No.
Description
Spec.
Qty.
No.
Description
Spec.
Qty.
61
Flat Washer
Φ6*Φ12*1
4
78
Lock Washers for
Shaft
D12
2
62
Bolt
M6*9
7
79
Magnetic Board
Shaft
1
63
Screw
ST4.2*20
6
80
Magnetic Board
1
64
Belt
310PJ6
1
81
Needle Sensor
1
65
Pulley
1
82
Bolt
1
66
Round Magnet
1
83
Tension Spring 2
1
67
Three Slot Nut
1
84
Induction Line 1
1
68
Washer
1
85
Screw
ST4.2*16
5
69
Collar Ball
2
86
Inert Wheel
1
70
Collar Housing
2
87
Idler Connecting
Rod
1
71
Lock Washer
1
88
Plastic Nut
M8
1
72
Hex Nut
1
89
Tap Bolt
1
73
Two Slot Nut
1
90
Flat Washer
Φ10.5*Φ16*0.5
1
74
Black Magnet
4
91
Tension Spring 1
1
75
Magnet
Positioning Grid
1
92L
Left Cover
1
76
Screw
ST3*10
5
92R
Right Cover
1
77
Spring Washer
D6
2
93
Crank Plug
2
Ordering Replacement Parts (U.S. and Canadian Customers only)
Please provide the following information in order for us to accurately identify the part(s) needed:
✓The model number (found on cover of manual)
✓The product name (found on cover of manual)
✓The part number found on the “EXPLODED DIAGRAM” and “PARTS LIST” (found near the front
of the manual)
Please contact us at [email protected] or 1- 877 - 90SUNNY (877-907-8669).

5
HARDWARE PACKAGE
2

6
ASSEMBLY INSTRUCTIONS
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [e-mail] or 1-877-90SUNNY
(877-907-8669).
STEP 1:
Attach Front Stabilizer (No. 7) and
Rear Stabilizer (No. 2) to Main Frame
(No. 1) with 4 Carriage Bolts (No. 4), 4
Arc Washers (No. 5), and 4 Nuts (No.
6). Tighten and secure with Spanner
(No. 51).
STEP 2:
Connect Trunk Wire (No. 28) to
Sensor Wire (No. 27). Then, connect
Tension Control Wire (No. 35a) with
Tension Wire (No. 29).
Note: Please make sure the Tension
Control Knob (No. 35) is at the lowest
resistance level (level 1, all the way to
the left) before you connect the Tension
Control wire.
Insert Handlebar Post (No. 36) to
Main Frame (No. 1) with 4 Screws
(No. 26) and 4 Arc Washers (No. 25).
Tighten and secure with Allen Wrench
(No. 47).
#51 1PC
#47 1PC
35a
35a

7
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [e-mail] or 1-877-90SUNNY
(877-907-8669).
STEP 3:
Lock Swing Rod (No. 24L/R) to Handlebar
Post (No. 36) with 2 Nylon Nuts (No. 31) and
2 Washers (No. 16), then attach 2 Ball Caps
(No. 18).
Lock Connecting Rod (No. 22L/R) to the
cranks of Main Frame (No. 1) with 2 Hinge
Bolts (No. 11L/R), 2 Wave Washers (No. 49),
2 Spring Washers (No. 42), and 2 Nylon
Nuts (No. 17L/R). Tighten and secure with
Allen Wrench (No. 48) and Spanner (No.
51). Then, cover with 4 Ball Caps (No. 18)
and 2 Ball Caps (No. 9).
CAUTION: Part 11 is labeled L for LEFT and
R for RIGHT. Please make sure you have the
correct bolt before installing.
NOTE: Please make sure to turn Hinge Bolt
(No. 11L) counter clockwise, Hinge Bolt
(No. 11R) clockwise, Nylon Nut (No. 17L)
clockwise, and Nylon Nut (No. 17R)
counter clockwise.
★Failure to follow procedures may result in
permanent damage to your machine.
(If you are having trouble with assembly of
Hinge Bolt (No. 11L/R), please see the next
page for alternate assembly method.)
#51 1PC
#48 1PC

8
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [e-mail] or 1-877-90SUNNY
(877-907-8669).
STEP 4:
Insert Handlebar (No. 46 L/R) into Swing
Rod (No. 24L/R). Tighten with 2 Knobs
(No. 38), then cover with 2 Ball Caps (No.
30).
ALTERNATE INSTALLATION METHOD:
STEP 1:
Disconnect the Link Connector Combination (No.
13L/R) from the Connecting Rod (No. 22L/R).
STEP 2:
Insert the 2 Hinge Bolt (No. 11L/R) through the 2
Wave Washer (No. 49), then through the hole of the
Link Connector Combination (No. 13L/R). Screw
the Hinge Bolt (No. 11L/R) into the crank arm.
*Remember when assembling the left side, you
must screw counter-clockwise to tighten* Connect
the Spring Washer (No. 42) and Nylon Nut (No.
17L/R) and attach the Ball Cap (No. 18). You can
now reattach the Link Connector Combination
(No. 13L/R) to the Connecting Rod (No. 22L/R).
IMPORTANT:
The Hinge Bolt (No. 11L/R) must fully penetrate the
Link Connector Combination (No. 13L/R) and
crank. This will ensure the stability and durability of
your Elliptical.
NOTE:
In order to install the hinge bolt properly, keep it
perfectly straight as the bolt goes through the pedal
arms and the crankshaft. If the hinge bolt is
connected to the crankshaft at an angle, damage to
both the hinge and the crankshaft may occur.
CORRECT
INCORRECT
INCORRECT
#51 1PC
#48 1PC

9
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [e-mail] or 1-877-90SUNNY
(877-907-8669).
STEP 5:
Attach Pedal (No. 21L/R) to
Connecting Rod (No. 22L/R) with 4
Bolts (No. 20) and 4 Washers (No.
14), 4 Nylon Nuts (No. 15). Tighten
and secure with Spanner (No. 51).
STEP 6:
Remove the preassembled 2 Screws
(No. 41) from Computer (No. 43).
Connect Trunk Wire (No. 28) to
Computer Wire (No. 43a).
Attach Computer (No. 43) to
computer holder on the top of
Handlebar Post (No. 36) with 2
Screws (No. 41) that were removed
from Computer (No. 43).
The assembly is complete!
#51 1PC
#50 1PC