Sunny Health & Fitness SF-B1001 User manual

INDOOR CYCLING BIKE
SF-B1001
USER’S MANUAL
IMPORTANT! Please read this manual carefully before using this product. Retain
owner’s manual for future reference. For Customer Service, please contact:
[email protected]

IMPORTANT SAFETY INFORMATION
We thank you for choosing our product. To ensure your safety and health, please use this
equipment correctly. It is important to read this entire manual before assembling and using the
equipment. Safe and effective use can only be assured if the equipment is assembled,
maintained, and used properly. It is your responsibility to ensure that all users of the equipment
are informed of all warnings and precautions.
1. Before starting any exercise program you should consult your physician to determine if you
have any medical or physical conditions that could put your health and safety at risk or
prevent you from using the equipment properly. Your physician’s advice is essential if you
are taking any medication that may affect your heart rate, blood pressure, or cholesterol
level.
2. Be aware of your body’s signals. Incorrect or excessive exercise can damage your health.
Stop exercising if you experience any of the following symptoms: pain, tightness in your
chest, irregular heartbeat, shortness of breath, lightheadedness, dizziness, or feelings of
nausea. If you do experience any of these conditions, you should consult your physician
before continuing with your exercise program.
3. Keep children and pets away from the equipment. The equipment is designed for adult use
only.
4. Use the equipment on a solid, flat level surface with a protective cover for your floor or
carpet. To ensure safety, the equipment should have at least 2 feet of free space all around
it.
5. Ensure that all nuts and bolts are securely tightened before using the equipment. The safety
of the equipment can only be maintained if it is regularly examined for damage and/or wear
and tear.
6. It is recommended that you lubricate all moving parts on a monthly basis.
7. Always use the equipment as indicated. If you find any defective components while
assembling or checking the equipment, or if you hear any unusual noises coming from the
equipment during exercise, stop using the equipment immediately and don’t use the
equipment until the problem has been rectified.
8. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that may
become entangled in the equipment.
9. Do not place fingers or objects into the moving parts of the equipment.
10. The maximum weight capacity of this unit is 220 pounds.
11. This equipment is not suitable for therapeutic use.
12. Move with caution when lifting and moving the equipment. Always use proper lifting
technique and seek assistance if necessary.
13. Your product is intended for use in cool, dry conditions. You should avoid storage in
extremely cold, hot, or damp places as this may lead to corrosion and other related
problems.
14. This equipment is designed for indoor use only! It is not intended for commercial use!
1

EXPLODED DRAWING
2

PARTS LIST
NOTE:
Most of the listed assembly parts have been packaged separately, but some hardware
items have been preinstalled. In these instances, simply remove and reinstall the hardware
assembly as required.
Please reference theindividual assembly stepsand make note of all preinstalled hardwre.
Prior toassembly of thisproduct, remove all components from the package and verify all
the listed parts aresupplied
HARDWARE TOOLS
Part No.
Description
Qty
Part No.
Description
Qty
1
Main frame
1
17
Phillips tapping screw
2
2
Front stabilizer
1
18
Hex nut M10
4
3
Rear stabilizer
1
19
Water bottle holder
1
4
Handlebar
1
20
Nylon nut
2
5
Seat post
1
21
Foam grip
2
6
Seat slider
1
22
End cap
2
7
Saddle
1
23
Allen bolt
4
8
Pop-pin knob
3
24
Spring washer
4
9L/R
Pedal
1 set
25 A/B
Handlebar cover
1 set
10L/R
Crank
1 set
26
Handlebar post
1
11
Leveler feet
4
27
Phillips screw
4
12
Oblong cap
4
28
Allen bolt
2
13
Flat washer
10
29
Roller
2
14
Allen bolt
4
A
Allen Wrench S6
1
15
Plastic bushing
3
B
Spanner
1
16
Square cap
1
A
B
S6
S 13, 14, 15
3

ASSEMBLY INSTRUCTIONS
STEP 1:
Install the Front Stabilizer (No. 2) and Rear Stabilizer (No. 3) to the Main Frame (No. 1)
with the Bolts (No. 14) and Flat Washers (No. 13). Ensure the Foot Levelers (No. 11) are
on the bottom and the transportation wheels are facing up at the front of the bike.
Attach the Water Bottle Holder (No. 19) to the Main Frame (No. 1) with Screws (No. 17).
NOTE: The Foot Levelers (No. 11) under the stabilizers can be adjusted to compensate for
uneven ground.
4

ASSEMBLY INSTRUCTIONS
STEP 2:
Attach the Handlebar (No. 4) to the Handlebar Post (No. 26) and secure with Allen Bolts
(No. 23), Flat Washers (No. 13) and Spring Washers (No. 24).
Set the Lower Handlebar Cover (No. 25B) on the square tube of the Handlebar Post (No.
26) in alignment with the four grooves on the mouth of the Lower Handlebar Cover (No.
25B). Slide the Lower Handlebar Cover (No. 25B)onto the top of the square tube of the
Handlebar Post (No. 26) and rotate the cover 45 degrees to align it with the Handlebar (No.
4).
Use Phillips Screws (No. 27) to fix the Top Cover (No. 25A) to the Lower Handlebar
Cover (No. 25B) so that the Handlebar (No. 4) and Handlebar Post (No. 26) are in
between the Handlebar Covers (No. 25A/B). Turn and loosen the Knob (No. 8), pull the
pin, and insert the handlebar assembly into the main frame simultaneously. Ensure the pin
settles into the desired hole before securing the Knob (No. 8).
5

ASSEMBLY INSTRUCTIONS
STEP 3:
Attach the Saddle (No. 7) onto the Seat Slider (No. 6) tightly with the Spanner (No. B).
Adjust the Seat Slider (No. 6) to the desired position before securing the Seat Slider (No. 6)
onto the Seat Post (No. 5) tightly with Pop-pin Knob (No. 8).
Insert the Seat Post (No. 5) into the rear upright tube of the Main Frame (No. 1) and adjust
the height to the desired location. Secure tightly with the Pop-pin Knob (No. 8).
NOTE: You may adjust the distance of the Seat Slider (No. 6) by loosening the Pop-pin
Knob (No. 8) on the Seat Post (No. 5). Ensure the Saddle (No. 7) is secured tightly onto the
Seat Slider (No. 6) before adjusting.
To adjust the height of Seat Post (No. 5), loosen the Pop-pin Knob (No. 8) on the rear
upright tube on Main Frame (No. 1).
6

ASSEMBLY INSTRUCTIONS
STEP 4:
Attach the Left & Right Pedals (No. 9L/R) to their corresponding Crank (No. 10 L/R).
Before you begin, immobilize the crank arms by turning the pop-pin knob all way to the right.
Left Pedal: The left pedal is marked L for left side. Align the Left Pedal (No. 9L) to the Left
Crank Arm (No. 10L) at 90 degrees and insert the pedal. Turn counter-clockwise as tightly
as you can with your hand then secure with Spanner (B).
Right Pedal: The right pedal is marked R for right side. Align the Right Pedal (No. 9R) to
the Right Crank Arm (No. 10R) at 90 degrees and insert the pedal. Turn clockwise as
tightly as you can with your hand then secure with Spanner (B).
7

OPERATIONAL INSTRUCTIONS
LEVELING THE BIKE
This bike can be leveled to compensate for uneven ground. To
level the bike, turn the 4 Foot Levelers (No. 11) located under
the Front and Rear Stabilizers (No. 2 & 3).
RESISTANCE ADJUSTMENT
The pedal resistance is controlled by the tension knob. To
increase resistance, turn the tension control knob clockwise
(+) . To decrease the resistance, turn the tension control knob
counter-clockwise (-) . Resistance adjustments can be made at
any time. To stop the bike completely during use, use the
emergency brake by pushing down on the tension knob.
SEAT ADJUSTMENT
Appropriate seat height ensures an efficient workout, reduces
the risk of injury, and makes your ride more comfortable.
Adjusting the seat forward or backward helps target different
body muscle groups.
1. Place one pedal inthe upward position.Place your foot in the
toeclips andmountthebike.
2. If your leg is bent too much, you should move the seat up. If
your foot cannot touch the pedal or your leg is too straight,
you should move the seat down.
3. Dismount the bike. Loosen and pull the Pop-pin Knob (No. 8) to
raise or lower the seat post to the desired position. Make sure the
pop-pin settles into the desired hole then secure firmly.
4. Loosen and pull the Pop-pin Knob (No. 8) out to move the Seat
Slider (No. 6) forward or backward to the desired position. When
the seat slider isinthe desired position then secure the pop-pin.
8

OPERATIONAL INSTRUCTIONS
HANDLEBAR ADJUSTMENT
Loosen and pull the Pop-pin Knob (No. 8) out to raise or lower the
Handlebar (No. 4) to the desired position. Make sure the pop-pin
settles into the desired hole before securing it tightly.
PEDAL STRAP ADJUSTMENT
Place the ball of each foot inthe toe clip until the front of the shoe
fits into the toe clip cage. Rotate one foot within arm's reach and
pull up the strap until the toe clip cage fits the shoe snuggly.
Insert the strap’s end back into the hoop of the toe clip. Repeat
for the otherfoot.
Once you’re positioned comfortably, begin pedaling slowly with
your hands resting comfortably on the handlebar. After you feel secure, you can change
seat positions, hand positions, and resistance levels.
DISMOUNTING THE BIKE
Increase the resistance by turning the tension control knob clockwise until the flywheel stops or
decrease pedaling speed until you come to a complete stop.
WARNING!
Do not dismount the bike or remove your feet from the pedals until the pedals have completely
stopped moving.
MOVING THE BIKE
Carefully lift the rear stabilizer to move the bike to another location.
Move with caution as any sudden impact may affect the operation
of the machine or inflict injury.
9