Sunnydaze Decor RUSTIC BIRDHOUSE & GARDEN WATERING CAN User manual

WXF01970 Page 1 / 2
ASSEMBLY
1. From the access hole in the back of the fountain, locate the water tube and rmly connect the electric submersible
pump. Place the pump inside the fountain and run the power cord out the access hole. TIP: Familiarize yourself with
the pump. Water ow is controlled by a switch on the front of the pump. Moving the switch to (+) increases water ow,
(-) decreases water ow.
2. Place the birdhouse topper onto the top of the fountain, as shown.
3. Use a bucket or watering can to ll the fountain with enough clean water to keep the pump fully submerged during
operation, approximately 1.25" below the edge of the basin.
4. Plug the power cord into a properly grounded GFCI outlet.
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we sell.
Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof of purchase, with
the date of purchase as well as photos of the merchandise defect, must be provided. Photos are used to determine
the cause of defects and for future quality control. Register your warranty at https://tiny.cc/SunnydazeWarranty
If you have any questions, comments or concerns, feel free to contact us by phone at 833-982-1977, by email:
[e-mail], or via our contact us page at https://tiny.cc/SunnydazeContact
Purchase Date: / / Order/Customer Reference Number:
 
Fountain Body 1
Birdhouse Topper 1
Electric Submersible Pump 1
RUSTIC BIRDHOUSE & GARDEN WATERING CAN
OUTDOOR WATER FOUNTAIN
WNC-504
Read the assembly instructions carefully and follow the care instructions. Keep this manual for future reference.


NOTE: The water tubing is built into the fountain.
Take care when handling the water tube; detaching
the water tube from the fountain will damage the
fountain and void the product warranty.
Inspect packaging to ensure all
parts are accounted for before
disposing of packing materials.
Note: When rst used, there may be air in the pump. It may take several minutes for trapped air to escape, allowing water to ow.
11/2022
2
3
4
1

WXF01970 Page 2 / 211/2022
WARNING!
Manufacturer and seller expressly disclaim any and all liability from personal injury, property damage
or loss, whether direct or indirect, or incidental, resulting from the incorrect attachment, improper use,

• Ensure the pump is fully submerged under the water. If water is not flowing within several moments of the power cord
being plugged in, the pump may have air bubbles trapped in it, which can prevent water from circulating properly and/
or cause excess pump noise. Simply unplug the power supply for a few moments and plug it back in.
• If water is still not flowing, inspect the pump and tubing for obstructions.
• Check the flow control on the body of the pump, it may need to be adjusted to achieve the desired water flow rate.
• Pump noise can be caused by trapped air, low water level, or the pump being too close to the sides of the fountain.
Check the pump. Try moving the pump and/or adding water to help reduce pump noise.
• Soft surfaces may cause the fountain to become unbalanced. A large stepping stone or paving stone (not included) is
recommended to help ensure the fountain remains evenly balanced.
• Check to make sure the power outlet is working; consult a certified electrician if in doubt about electrical connections.
Troubleshooting

IMPORTANT SAFETY INFORMATION
• For outdoor use only.
• Keep fountain out of reach of children and pets.
• Make sure the power cord is away from traffic areas.
• Keep power cord away from all heat sources. Do not use electrical cords in areas with high temperatures.
• Check the water level frequently to ensure the pump remains fully submerged; never allow the pump to run dry as it will burn
out the motor.
• Always unplug the power supply before cleaning and maintaining the fountain and the recirculating pump.
• Always empty and store the fountain and pump indoors during freezing weather.
• For outdoor use only. Some splashing is normal; adjust the flow rate on the pump if the water rate is too high.
• Some climates and weather conditions increase water evaporation, requiring water to be added more frequently.
Frequently check water levels during times of high temperatures, wind, and long-term exposure to direct sunlight to
ensure the pump does not run dry. Never allow the pump to run dry as it will burn out the motor.
• Only use water in this fountain. Distilled water will help prevent mineral buildup but is not required. Tap water is okay
to use, but avoid heavily chlorinated water as it may damage the fountain and the pump.
• Periodically change the water to keep the water, fountain, and pump clean. Remove scale and buildup regularly.
DO NOT use harmful additives such as bleach, chlorine, etc.
DO NOT use anything that is abrasive to scrub the fountain.
DO NOT use a pressure washer to clean the fountain.
• Always unplug the power supply before cleaning and maintaining the fountain and the recirculating pump. Take care
when handling the pump; only pick it up by the body of the pump, never the power cord.
• During freezing weather, drain the fountain, disconnect the pump and store indoors; allowing ice to form may damage
the fountain in such ways as, but not limited to, fountain cracking and/or permanent pump damage.
• Over time, the finish may gradually mellow in color due to sun exposure; this is part of the natural aging process and
is not cause for return.
Care & Maintenance
If you experience issues with assembly or the product was damaged during shipping,
please contact our customer service team through one of the methods mentioned at the top of page 1.
Please have the item number and order information ready to expedite response time.