Sunnydaze Decor SSS-399 User manual

09/2019MZ14871BB Page 1 / 2
FLORAL MOTIF CERAMIC 3-TIER OUTDOOR WATER FOUNTAIN
WITH LED LIGHTS
SSS-399
Read the assembly instructions carefully and follow the care instructions. Save these instructions for future reference.
Select a smooth, level surface to place the fountain.

*2 people are recommended to safely assemble this product.
 
Ball Topper 1
Small Tier with LED Light Ring 1
Medium Tier with LED Light Ring 1
Large Column 1
Large Tier with
Electric Submersible Pump 1
AC Adapter 1
Pedestal 1
Water Tube 1
Rubber Washer 1
ASSEMBLY
1. Place the large tier with the built-in electric submersible pump onto the pedestal and twist the tier clockwise
to lock into place.
2. Run the long pump power cable through the tube in the large tier and through the pedestal. Pull the cord out
through the groove in the back-side of the pedestal.
3. Assemble the water tube and attach it onto the pump making sure the end with the rubber washer is on top.
Remove the rubber washer and save it for use during Step 7.
4. Slide the large column over the water tube and gently place the large column onto the large tier. Run the
light splitter cable (attached to the pump) up through the large column.
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we
sell. Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof
of purchase, with the date of purchase as well as photos of the merchandise defect, must be provided.
Photos are used to determine the cause of defects and for future quality control. Register your warranty at
www.serenityhealth.com/warranty/
If you have any questions, comments or concerns, feel free to contact us by phone at 888-881-4668, by email:
[e-mail], or via our contact us page at www.SerenityHealth.com/contact-us/
Purchase Date: / / Order/Customer Reference Number:
Inspect packaging to ensure all parts are accounted for
before disposing of packaging.
NOTE: There is a polyurethane foam lter/splash guard inside the ball topper;
this lter helps control water ow to prevent splashing. Do not remove or discard
this lter/splash guard.

Note: When rst used, there may be air in the pump. It may take several minutes for trapped air to escape, allowing water to ow.
You may need to add more water as the pump begins to circulate water through the fountain.
09/2019 Page 2 / 2MZ14871BB
5. *Run the light cable from the small tier down through the medium tier. Slide the tiers over the water tube and
rmly connect the light cables from both tiers to the light splitter cable (attached to the pump).
6. Gently place the tiers onto the large column, ensuring all cables are inside the fountain. Do not allow the
cables to get caught/pinched between the tiers as this can damage the wires.
7. Place the rubber washer (from step 3) on the water tube. Twist the ball topper onto the water tube until it is
secure; do not over-tighten.
8. Firmly connect the pump power cable to the AC adapter.
9. Fill the large tier and medium tier with enough water to keep the pump fully submerged during operation.
10. Plug the power cord into a properly grounded GFCI outlet.
IMPORTANT INFORMATION
USE & CARE
• For outdoor use only. Some splashing is normal; adjust the flow rate on the pump if the water rate is too high.
• Check the water level frequently to ensure the pump remains fully submerged; never allow the pump to run dry as it will burn out the motor.
• Only use water in this fountain. Distilled water will help prevent mineral buildup but is not required, avoid heavily chlorinated tap water as
it may damage the fountain or pump.
• Periodically change the water to keep the water, fountain and pump clean. Remove scale and buildup regularly.
DO NOT use harmful additives such as bleach, chlorine, etc.
DO NOT use a pressure washer or abrasive materials to wash the fountain
• Always shut off the power supply before cleaning and maintaining the fountain and the recirculating pump.
• Take care when handling the pump; only pick it up by the body of the pump, never by the power cord.
• During freezing weather, drain the fountain, disconnect the pump and store indoors; allowing ice to form may crack the fountain.
TROUBLESHOOTING
• Ensure that the pump is fully submerged and add water to the basin if necessary.
• Check the pump and tubing for obstructions.
• Check the flow control on the body of the pump as it may need to be adjusted to achieve the desired flow rate.
• If the light is not working, ensure the cables are fully connected and the seal is adequately tightened (do not over-tighten).
• If water is not flowing within several moments of the fountain being plugged in, unplug the power supply for a few moments and plug it back
in; the pump may have trapped air which can prevent water from circulating properly.
• Check to make sure the power outlet is working; if in doubt about electrical connections, consult a certified electrician.
