Sunnydaze Decor SSS-602 User manual

DOUBLE TIER
CERAMIC OUTDOOR FOUNTAIN WITH LIGHTS
SSS-602
Read the assembly instructions carefully and follow the care instructions. Keep these instructions for future reference.
Select a smooth, level surface to place the fountain.

03/2020MZ15103BA Page 1 / 2
Purchase Date: / / Order/Customer Reference Number:
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we sell.
Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof of purchase, with
the date of purchase as well as photos of the merchandise defect, must be provided. Photos are used to determine
the cause of defects and for future quality control. Register your warranty at https://tiny.cc/SunnydazeWarranty
If you have any questions, comments or concerns, feel free to contact us by phone at 888-881-4668, by email:
customerser[email protected], or via our contact us page at https://tiny.cc/SunnydazeContact
Inspect packaging to ensure all
parts are accounted for before
disposing of packing materials.
 
Topper 1
Small Tier with LED Light Ring 1
Column 1
Large Tier with
Electric Submersible Pump 1
AC Adapter 1
Pedestal 1
Water Tube 1
Rubber Washer 1
NOTE: There is a polyurethane foam lter/splash guard inside the topper, do not remove
or discard the lter/splash guard. The lter helps control water ow to prevent splashing.
2-PERSON
ASSEMBLY
RECOMMENDED
ASSEMBLY
1. Place the large tier with the pre-attached electric submersible pump onto the pedestal and twist to lock into place.
2. Run the longer cable that is attached to the through the tube in the large tier and pedestal. Make sure the power cable
is under the groove on the bottom of the pedestal.
3. Attach the water tube to the pump, making sure the end with the rubber washer is on top. Remove the rubber washer
and save it for use during Step 7.
4. Slide the column over the water tube and gently place it on the large tier. Run the light cable (attached to the pump)
up through the column.

5. Slide the small tier over the water tube and rmly connect the light cable to the short cable on the pump.
6. Gently place the small tier onto the column, ensuring all cables are inside the fountain. Do not allow the cables to get
caught/pinched between the tiers as this can damage the wires.
7. Place the rubber washer (from step 3) on the water tube. Twist the topper onto the water tube until it is secure; do not
over-tighten.
8. Firmly connect the pump power cable to the AC adapter.
9. Fill both tiers with enough water to keep the pump fully submerged during operation.
10. Plug the power cord into a properly grounded GFCI outlet.
03/2020MZ15103BA Page 2 / 2

IMPORTANT INFORMATION
USE & CARE
• For outdoor use only.
• Some splashing is normal; adjust the flow rate on the pump if the water rate is too high.
• Check the water level frequently to ensure the pump remains fully submerged; never allow the pump to run dry as it will burn
out the motor.
• Only use water in this fountain. Distilled water will help prevent mineral buildup but is not required, avoid heavily chlorinated
water as it may damage the fountain or pump.
• Periodically change the water to keep the fountain and pump clean. Remove scale and buildup regularly.
DO NOT use harmful additives such as bleach, chlorine, etc.
DO NOT use a pressure washer or abrasive materials to wash the fountain.
• Always shut off the power supply before cleaning and maintaining the fountain and the recirculating pump.
• Take care when handling the pump; only pick it up by the body of the pump, never by the power cord.
• During freezing weather, drain the fountain, disconnect the pump and store indoors; allowing ice to form may damage the
fountain in such ways as, but not limited to, the fountain cracking, permanent pump damage, and /or lighting malfunctions.
TROUBLESHOOTING
• Ensure that the pump is fully submerged and add water if necessary.
• If water is not flowing within several moments of the fountain being plugged in, the pump may have trapped air which can
prevent water from circulating properly. Simply unplug the power supply for a few moments and plug it back in. Also check the
pump and tubing for obstructions.
• If water is not flowing or water is splashing, check the flow control on the body of the pump; it may need to be adjusted to
achieve the desired flow rate.
• If the light is not working, ensure the cables are fully connected and the seal is adequately tightened (do not over-tighten).
• Make sure the adapter cable is fully connected to the pump power cable.
• Make sure the power outlet is working; if in doubt about electrical connections, consult a certified electrician.
WARNING!

indirect, or incidental, resulting from the incorrect attachment, improper use, inadequate maintenance, or neglect of this product.
Note: When rst used, there may be air in the pump. It may take several minutes for trapped air to escape, allowing water to ow.
You may need to add more water as the pump begins to circulate water through the fountain.