Sunnydaze Decor XSS-431 User manual

BACKSIDE VIEW
 
Fountain Topper
Bottom Basin 1
Electric Submersible Pump 1
AC Adapter 1
SS3190263 Page 1 / 2
STACKED BASIN TRIO
OUTDOOR FOUNTAIN WITH LED LIGHTS
XSS-431
Read the assembly instructions carefully and follow the care instructions. Save these instructions for future reference.

ASSEMBLY
1. Locate the light cables inside the fountain topper and inside the basin. Firmly connect the light cables to the shorter
cable on the pump.
2. Connect the water tube (pre-assembled into the fountain topper) to the pump.
3. Ensuring the pump power cord runs out and through the groove in the backside of the bottom basin, and the pump stays
rmly attached to the water tube, set the pump in the bottom basin and gently place the topper onto the basin.
4. Firmly connect it to the AC adapter.
5. Fill the fountain with enough water to keep the pump fully submerged during operation, approximately 4000 mL.
6. Plug the power cord into a properly grounded GFCI outlet.
Note: When rst used, there may be air in the pump. It may take several minutes for trapped air to escape, allowing water to ow.
NOTE: The water tubing is built into the fountain topper. Take
care when handling the water tube; detaching the water tube from the
fountain will damage the fountain and may void the product warranty.
Purchase Date: / / Order/Customer Reference Number:
01/2020
1
2
4
5
6
3
Ensure all parts are
accounted for before
disposing of packaging.
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we sell.
Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof of purchase, with
the date of purchase as well as photos of the merchandise defect, must be provided. Photos are used to determine
the cause of defects and for future quality control. Register your warranty at https://tiny.cc/SunnydazeWarranty
If you have any questions, comments or concerns, feel free to contact us by phone at 888-881-4668, by email:
customerser[email protected], or via our contact us page at https://tiny.cc/SunnydazeContact

SS3190263 Page 2 / 201/2020
USE & CARE
• For outdoor use only.
• Check the water level frequently to ensure the pump remains fully submerged; never allow the pump to run dry as
it will burn out the motor.
• Only use water in this fountain. Distilled water will help prevent mineral buildup but is not required, avoid heavily
chlorinated water as it may damage the fountain and pump.
• Periodically change the water to reduce scale and buildup — clean the fountain and pump regularly for optimal
performance and appearance.
DO NOT use harmful additives such as bleach, chlorine, etc.
DO NOT use a pressure washer or abrasive materials to wash the fountain.
• Always shut off the power supply before cleaning and maintaining the fountain and the pump.
• Take care when handling the pump; only pick it up by the body, never by the power cord.
• During freezing temperatures, drain the fountain, disconnect the pump and store indoors; allowing ice to form may
crack the fountain and will damage the pump.
TROUBLESHOOTING
• Ensure that the pump is fully submerged at all times; add water to the reservoir if necessary.
• If water is not flowing within several moments of the fountain being plugged in, the pump may have trapped air
which can prevent water from circulating properly. Simply unplug the power supply for a few moments and plug it
back in.
• Check the pump and tubing for obstructions.
• Some splashing is normal; adjust the flow rate on the body of the pump to achieve the desired flow rate.
• If lights are not working, ensure the cables are fully connected and the plastic collars are adequately tightened;
do not over-tighten the collars.
• Check to make sure the power outlet is working; if in doubt about electrical connections, consult a certified electrician.
• Prevent water loss and damage to electrical sockets by creating a drip loop. Place the pump in the reservoir, then
drape the cord over the edge where the cord exits the fountain, ensuring the power cord remains below the wall
outlet. See diagram below for reference.


Drip Loop
If you are still experiencing issues, please contact our customer service team through one of the methods mentioned
at the top of page 1. To expedite response time, please have the item number and order information available.
IMPORTANT INFORMATION
WARNING!
             

