English
Using the Multi-Voltage AC
Adapter or the Sunpak
Powerpak for 51O-Volt
Batteries (Both Optional):
1) ForAC operation,be sure
to check that the
voltageselectoron your AC Adapter issetto
the appropriate voltage. Your AC Adapter
has been factory set for 220V. For use in
othercountries
where117V,127Y and
24OV
arestandard,
you may adjust the setting as
illustrated.
Remove
the small Phillipshead
screw located next to voltage window and
rotate
theselector
switch with a screw driver
to the proper
voltagesetting.
After the volt-
agesetting has been made,the screw must
be reinstalled
to prevent accidental move-
ment
of the selectorswitch.
(4)(5)
Note: lf the Multi-Voltage AC Adapter is
incorrectlyset.the adapter
will not function
properly
and may damage
your auto
433D.
. Forauto 433D, do not use the AC Adapter
otherthan the AD-27.
2) When using Multi-Voltage AC Adapter
or Sunpak Powerpak for 51O-Volt Bat-
teries, always set BatterylAC HV Se-
lector Switch to AC/HV position.
Plug
into
the
AC/High Voltage
socketon the
flash and into a standard wall outlet as
illustrated.The AC Adapterwill supplyvir-
tuallyunlimited
flashes
and is idealfor in-
dooruse.
(6)
3) When you use the optional accessory
Sunpak Powerpakfor 51O-Volt Battery,
first
attachthe supplied
plug adapterto the end
of Powerpakcord and plug it into the auto
433D in
thesame
manner
as
you would with
the Multi-Voltage
AC Adapter.The Sunpak
Powerpak for 510-Volt Battery allows ex-
tremely
rapid recycle
times and the greatest
numberof flashes.
(7)(8)
CAUTION: Even
when your
auto
433D is
used
with external
power sources,always store bat-
teriesinsidefor dedicatedfunction. Your auto
433D is not interfaced
to the camera without
internalbatteries.
4
Mounting the Flash to the
Gamera:
CAUTION: For mounting or detaching the
autozoom433D on or from the camera,always
make
surethe On/Off Switch is
at "OFF" posi-
tion or the camera
may be damaged.
Slio the unit onto the camera'shot shoe.
Turn the knurledlock ring clockwiseto in-
sure
secure
mounting
to your
camera'sshoe.
(e)
Note: When using Olympus cameras,
make
surethat the appropriate
accessoryshoe as
below is attachedto your cameraand then
put the autozoom 433D on it.
o For OM-2N, OM-1N: accessoryshoe
#4
. For OM-2: accessoryshoe
#3
o For OM-10: mount
theautozoom
433D
onto the built-in hot shoe.
Setthe Camerashutterto the fastest
shutter
speedsynchronized
for electronicflash. For
SLR cameras,the highest usable speed is
generally 1/60th second; however. some
permit flash synchronization of up to
1l125th second. To be sure, referto your
camera's
instructionmanual.
(10)
AUTOMATICOPERATION:
The sensitiveSilicon Photo Transistor
of your
autozoom 433D Sensormeasures
the light re-
flected by your subject and automaticallycon-
trols the flash duration to assurecorrect expo-
sure
within a wide range of distances.
lt's easy
to use:
A. Slidethe ISOFilm
SpeedScale
till
the
ISOof
film in use is visible in the ISO speed
window.
(Example: ISO100)
B. For the maximum distance
range in auto-
matic
operation,
move
the
Auto/Manual Se-
lector Switch to the green "A" position so
that the green "
A" is visible in the
Auto/Manual Mode Window and f
l2 will
appear.
Then setyour camera
lens
opening
(for ISO 100 film,
the lens
openingis'tl2).
Your flash and lens are now set for correct
exposure
at any distance
between2.3 m and
1
8 m (8 feet and 60 feet). (1
1
)
1.
2.
