Sunricher DALI SR-2300TR-RGWB-US-DT8 User manual

DT8 DALI RGBW Touch Controller 09.230WU8.04159
Function introduction
Important: Read All Instruct ion s Pri or to I nst all ati on
Front side
Back side
Product Data
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Safety & Warnings
75x120x29.1mm
Output DALI signal
Operation Current 4mA
Operating temperature 0-40°C
Relative humidity 8% to 80%
Dimensions
Power Supply Supply By DALI Bus
Waterproof grade Ip20
ON/OFF button
Red channel: click to turn ON/OFF,
press and hold down to
increase/decrease light intensity
RGB color wheel
Blue channel: click to turn ON/OFF,
press and hold down to
increase/decrease light intensity
Green channel: click to turn ON/OFF,
press and hold down to
increase/decrease light intensity
White channel: click to turn ON/OFF,
press and hold down to
increase/decrease light intensity
Play/Pause button, click to
play/pause running effects, press
and hold down to speed up/down
Click to get CW, NW, WW
mixed by RGB
Brightness button, press and hold
down to increase/decrease light
intensity
Scene button, press and hold down
to save a scene, click to recall, the
saved scene will cover the
predefined one
• Touch sensitive.
• Glass interface(white & black).
• Comply to DALI standard protocol IEC 62386-102, IEC
62386-207, IEC 62386-209 and in compliance with DALI
products from other international incorporation
• Enable to control 1 DALI Group and 3 DALI Scenes.
• Enable to set start DALI group number (0-15) by rotary
switch on the back.
• Support DT8 devices
• Color adjustment according to DALI specifications of
Device Type 8, Color Type RGBWAF.
• Each DT8 device is controlled via a single DALI address
• Built-in 8 Color Sequences
Wiring diagram
D2 D2
43.58 mm
65.58 mm
DALI signal output
DALI Wal l Pan el
Controll er
83.00 mm
19.4 mm
Rotary Switch for Assigning
Group (Total 16 Groups)
D1D1
DALI BUS
D1
D2
V+
V-
OUTPUT
12V/24V/36V
CV PSU
Con nect wi th RGBW L ED Stri p
V+ V+
R- R-
G- G-
B- B-
W- W-
Con nect wi th RGBW L ED Stri p
V+ V+
R- R-
G- G-
B- B-
W- W-
DT8 DALI R GBW Dimme r
0-6 0- 9
LED O UTPUT
12- 36V DC
POW ER INPU T
V-
V-
V+
V+
+
R-
G-
B-
W-
D1
D2
D1
D2
DAL I SIGNA L
DT8 DALI R GBW Dimme r
0-6 0- 9
LED O UTPUT
12- 36V DC
POW ER INPU T
V-
V-
V+
V+
+
R-
G-
B-
W-
D1
D2
D1
D2
DAL I SIGNA L
Rotary Switch for Assigning
Scene (Total 16 Scenes)
D2 D2
DAL I Wall Pa nel
Con trol ler
D1D1

Installation
Operation
2. Set starting Scene number via rotary switch on the back: (0-15 selectable)
• This DALI touch panel controller enables Scene selection commands for up to 3 Scenes to be sent to the DALI
circuit. A rotary switch on the back is used to select Scenes you would like to control and set the starting scene
number, and total 16 Scenes (0-15) can be selected.
• When the rotary switch arrow position is at X (0-15), Scene button S1 controls Scene X, S2 controls Scene
X+1, and S3 controls Scene X+2.
Please refer to the detailed Scene setting table as follows:
1. Set starting Group number via rotary switch on the back: (0-15 selectable)
• This DALI touch panel controller enables dimming commands and DT8 commands to be sent to 1 Group of
devices on the DALI circuit. A rotary switch on the back is used to select Groups you would like to control and
set the starting Group number, and total 16 Groups (0-15) can be selected.
• When the rotary switch arrow position is at 0, all 16 Groups of devices are controlled through broadcast.
• When the rotary switch arrow position is at X except 0 (1-15), the panel controls Group X-1 of devices.
Please refer to the detailed Group setting table as follows:
Rotary Switch
Position
DALI Group
Selected
0
Broadcast
1
0
2
1
3
2
4
3
5
4
6
5
7
6
8
7
9
8
10
9
11
10
12
11
13
12
14
13
15
14
Rotary Switch
Position
Scene assigned
to S1
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Scene assigned
to S2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0
Scene assigned
to S3 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 1