Suntec Wellness CoolBreeze 4000 SV User manual

1
CoolBreeze 4000 SV + SV-RC
OPERATING INSTRUCTIONS

2
GUIDE TO BETTER FAN MAINTENANCE
1. As an added safety precaution, when removing the front guard you may have to use a small pair of pliers to unfasten
the safety clips when be fire you remove screws and clips from the external plastic ring
2. Use in a dry place, free of excessive humidity.
3. Keep fan clean. wipe away dirt with a clean cloth.
4. Do not use any harsh cleaners.
5. before putting the fan in storage, clean it thoroughly, pack it
with a vinyl bag and store it in a dry place.
6. when reassemble fan ,make sure to follow the instructions for
how to assemble.
Important note :Please save color box return goods will not be
Accepted if not packed in original color box. thank you
PARTS NAME
CAUTION
1. Do not plug the AC cord into the wall outlet outlet until fan has been completely assembled.
2. Use power source of the fan according to electric nameplate at the back of switch box.
Consumption: 12”(50W)/16”(50W)
HOW TO ASSEMBLE
The only tool needed for this assembly procedure is a Philip
screw driver
1. Assembling the cross-bar feet
2. First of all, loosen and remove the
Four screws from bars, next cross
The barA and bar B. Be sure to align
The four holes in the bar to the four
Hole on the flange at the same time
Align the projection on the flange
With the extra hole on barA, then
1 Guard
2 Blade
3 Oscillation knob
4 Motor
5 Switch box
6 Slider switch
7 Switch box set screw
8 Cord
9 Inner pipe
10 Outer pipe
11 Base cap
12 Cross-bar feet
13 Height adjustment knob

3
Tighten the four screws and insert the base cap down over the feet.
3. mounting the switch box
“caution” never remove the inner pipe stopper if you remove the Inner pipe stopper service may be necessary. Never
loosen the
Inner pipe set screw
(1) locsen the switch box set screw by turning it to the left
(2) now place the hole in the bottom of the switch box over the inner
pipe.
(3) turn the switch box set screw clockwise and tighten it firmly
mounting nose of the fan
parts identification of the fan nose
1- motor
2- rear guard
3- guard lock nut
4- blade
5- blade cap
6- front guard
7- screw
4. mounting the rear guard.
Mount the rear guard on the Motor and secure it with the Guard
lock nut.
5. mounting the blade
insert the blade onto the motor shaft. Tighten the blade with
the blade cap.
6. mounting the front guard
there are two type construtions of fan front guard, each is assembled
according to followings
(1) mounting the reticular guard
a. mounting the front guard by inserting the hook at the top side of the
front guard over the rear guard. unite them by pressing their sides in order
that the two guards are fixed in the external plastic ring.
b .lock the clip and secure it with the screw.
HOW TO USE SAFELY
- Never touch the engine with your hands or feet if they are wet, damp or naked
- Before cleaning the fan pull the plug from the outlet
- Remove the plug from the outlet when not in use
- To eliminate risk of short circuit does not immerse the motor in water or any other liquid
- This appliance is not intended for use by persons (including children) with reduced
Physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
- If the appliance, the plug or power cord show visible damage, do not use it and
ensure it checked by qualified people
- To avoid overheating, it is recommended to remove the power cable for its entire length
- Do not link to be taken not recommended by the manufacturer

4
- Make sure the cable connected to the outlet does not impede the movement of persons
- Not place the fan near heat sources or flammable materials (curtains, upholstery, etc. ...)
- Not use outdoors
- Household products
- Not be used for purposes other than those recommended by the manufacturer
(2) mounting the spoke guard. hold the Front guard so that the trade mark is Level and the two projections on the
Front guard are centered over the Rear guard. Now push all the safety Clips firmly into place.
Caution
Never operate the fan with a cracked or damaged fan blade.
How to use
1. Speed control
Speed of a fan is controlled by a key or slider switch . Each is operated
according to followings
(1) Operation of slider switch to turn on the fan simply, slide switch To any of the
speed positions (1-2-3), To turn it off .slide switch to ”O” Position.
(2) Operation of key switch
To turn on the fan, simply push any of The speed control push buttons (1-2-3),
To turn it off . Push the “o” button.
2. Oscillation
Push down the oscillation knob and the Fan will oscillate ,pull up the knob, the
Fan will not oscillate
3. Tilting adjustment
Always switch the fan off before Making a tilt adjustment, the air Flow can be
adjusted upward or Downward by simply moving the Guard up or down
4. Hight adjustment
Loosen the height adjustment knob, Then adjust the pipe to the desired
Height and the tighten the adjustment knob
5. This fan include a 7.5 hour timer .To operate timer, press TIMER button(located on
remote)Each button press will increase the tome by 0.5H+1H+2.5H+4H.Once set the
timer LED light will glow.
6. Remote control use AAA Battery.
NOTE CONCERNING PROTECTION OF ENVIRONMENT
This product must not be disposed of via normal household waste after its service life, but must be taken
to a collection station for the recycling of electrical and electronic devices. The symbol on the product, the
operating instructions or the packaging indicate such disposal procedures. The materials are recycable in
accordance with their respective symbols. By means of re-use, material recycling or any other form of
recycling old appliances you are making an important contribution to the protection of our environment.
Please ask your local council where your nearest disposal station is located.
© 2011 KLIMATRONIC
®
CoolBreeze
SUNTEC WELLNESS GMBH / HOLZSTRASSE 2 / 40 221 DÜSSELDORF / DEUTSCHLAND