Sunvic TL ONE User manual

Installation Guide
TL ONE
TL ONE
Electronic Thermostat

TL ONE
Installation Guide 3
1 Introduction
TL ONE is an electronic thermostat provided with a
2-pole switch and a room sensor to measure and control the
surface-mounted.
The thermostat has a button for adjusting the temperature
setting with a scale from ( ) 5-35°C. Furthermore, it has
a LED indicator showing standby periods (green light) and
heating periods (red light).
More information on this product can also be found at:
sunvic.co.uk
Table of Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 . . . . . . . . . . . . 4
1.2 Safety Instructions . . . . . . . . . . . . . . . . 5
2 Mounting Instructions . . . . . . . . . . . . . . . . 6
3 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 10
4 Disposal Instruction . . . . . . . . . . . . . . . . . . 12

TL ONE
Installation Guide4
1.1
Operation voltage 220-240 V~, 50 Hz
Standby power consump-
tion
Max 0.25 W
Relay:
Resistive load
Inductive load
Max 15 A / 3450 W @ 230 V
cos φ= 0.3 max 1 A
Sensing units NTC 15 kOhm at 25 °C
Sensing values:
0 °C
25 °C
50 °C
42 kOhm
15 kOhm
6 kOhm
Hysteresis ± 0.2 °C
Ambient temperature -10 to +30°C
Frost protection temper-
ature
5 °C -
Temperature range () 5-35°C with room
sensor
1 x 4 mm² or 2 x 2,5 mm²
Ball pressure temperature 75 °C
Pollution degree 2 (domestic use)
Type 1C
Storage temperature -20 to +65°C

TL ONE
Installation Guide 5
IP class 31
Protection class Class II -
Dimensions 85 x 85 x 36 mm
Weight 90 g
The product complies with the EN/IEC Standard“Automatic
electrical controls for household and similar use”:
• EN/IEC 60730-1 (general)
• EN/IEC 60730-2-9 (thermostat)
1.2 Safety Instructions
before installation.
IMPORTANT: When the thermostat is used to control a
Please also note the following:
• The installation of the thermostat must be done by an
regulations.

TL ONE
Installation Guide6
• The thermostat must be connected to a power supply
via an all-pole disconnection switch.
• Always connect the thermostat to continuous power
supply.
• Do not expose the thermostat to moisture, water,
dust, and excessive heat.
2 Mounting Instructions
Place the thermostat at a suitable height
on the wall (typically 80-170cm.).
In wet rooms, place the thermostat according
to local regulation on IP classes.
Do not place the thermostat on the inner
side of an exterior wall.

TL ONE
Installation Guide 7
Always install the thermostat at least 50 cm.
from windows and doors.
Do not place the thermostat in a way that
it will be exposed to direct sunlight.
Follow the steps below to mount the thermostat:
1. Open the thermostat:
devireg™550
3
5
6
24
20
30
40
50
• Press the release tab in the bottom of the ther-
• Carefully detach the front cover.
• Carefully detach the frame.

TL ONE
Installation Guide8
2. Connect the thermostat according to the connection
diagram.
IP31
-10T30
D531
Mains
220-240V~
Max. Load
15 (1) A
N L
N
LOAD
L
LOAD
9еквонатсуоповтсдовокуР
The screen of the heating cable must be connected
to the earth conductor of the power supply cable by
using a separate connector.
Note:
3. Mount and reassemble the thermostat.
• Fasten the thermostat to a socket or an exterior
wall box by driving the screws through the holes
in each side of the thermostat.
• Install the frame and front cover in the reverse
order of disassembly.
4. Turn on the power supply.

TL ONE
Installation Guide 9

TL ONE
Installation Guide
4 Disposal Instruction