Super Circuits PC164C Series User manual

PC164C / PC165 Series Back Focus Procedure
Step 1- Remove Lens Cover
Step 2- If using a C-Mount lenses it can be applied to the camera at this time
Step 3- Most current lenses are CS-Mount and require removal of the C/CS ring
Step 4- To remove the C/CS ring loosen but do not remove completely the two set screws and then remove the C/CS ring.
Step 5- Screw on the CS-Mount lens until a good picture is obtained and tighten the set screws
Step 6- Use the focus ring on the lens to obtain a finer focusing.
Note- If a C-Mount lens was applied and focus could not be obtained, please try the following:
●Ensure that the lens is in fact a C-Mount and not a CS-Mount
●Check the focus adjust on the lens
●If need be loosen the set screws and adjust the position of the lens and C/CS ring as one unit until a good focus is obtained.

WARNING
TO REDUCE THERISK OFFIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE
CAUTION
RISK OF ELECTRIC SHOCK
AWA
CAUTION : TO REDUCE THE RISK OFELECTRIC SHOCK,
DO NOT REMOVE COVER(0R BACK),
NO USER
- SERVICEABLE PATRS INSIDE.
REFER SERVICINGTO QUALIFIED SERVICE PERSONNEL
TABLE OF CONTENTS
A. PRECAUTIONS
B. SPECIAL FEATURES
C. APPEARANCE
D. INSTALLATION
E. SPECIFICATION
1. Do not attempt to disassemble the camera.
There are no user serviceable parts inside. Ask a qualified
service person for servicing.
2. Handle the camera with care.
Do not abuse the camera. Avoid striking, shaking, etc. Improper
handlingor storagecoulddamage the camera.
6
3. Do not expose the camera to rain or moisture, or try to
operate it in wet areas.
Turn the power off immediately and ask a qualified service
person for servicing. Moisturecan damage the camera.
4. Do not use strong or abrasive detergents when cleaning
the camera body.
Use a dry cloth to clean the camera when dirty. In case the
dirt is hard to remove, use a mild detergent and wipe gently.
Afterwards, wipe off the remained part of the detergent in it
with a dry cloth.
5. Clean the CCD faceplate with care.
Do not clean the CCD with strong or abrasive detergents.
Use lens tissue or a cotton tipped applicator and ethanol.
6. Never face the camera towards the sun.
Do not aim the camera at bright objects. Whether the camera
is in use or not, never aim it at the sun or other extremely bright
objects. Otherwise, blooming or smear may be caused.
7. Do notoperate the camerabeyond the specitiedtemperature,
f
humidity or power source ratings.
Use the camera under conditions where temperature is
between
-10°C-+40"C, and humidity is below 80%.

SPECIAL FEATURES
1
1. The following functions are built in.
(1)Auto Light Control (ALC)/Electronic Light Control(E/S)
(2)Automatic Gain control (AGC)
(3)Automatic White Balance(AWB)
2. ConspicuousLow Lux Sensitivityand extremely clear vision.
3. Signal-to-noise ratio of 45dB for colour & 50dB for B/W
(Equivalent to AGC Off)
4. Horizontal resolution of 380TV lines & 420 TV lines for Standard
resolution and 480TV lines
& 600 TV lines for High resolution.
5. Built-in electronic shutter (Auto iris function) and blooming-
free circuit
Built in auto iris functionenablesit to view againststrong light
and add the outlineclearerwith blooming free circuit
6. OLPF Built-in for colour version
Unlike usual cameras, this camera filters unnecessary noise
signals in dark view and feedback them with more clear
picture signals.
This makes it possible to eliminate disturbing dark noises in
low lux condition and ensure it to produce an extraordinary
clear picture at any light condition.
BiW Version Colour Version
R
INSTALLATION
1
1. Mounting Lens

2. View of angle and focus adjustment for built in
varifocal lens.
imur screw /
Horizontal
T C
Verltcal 65 5" 33.4"
a,rlance rcreh
* Please adjust focus & d~stancewith the screws on
the varifocal lens
3. Cable Connection
4. Operating Controls and Functions
Colour Version BIW Version
a HOW TO INSTALL THE AUTO-IRIS LENSCONNECTOR
@I. Cut off the iris control cable at the edgeof lensconnector and then cut off the
outer cable cover as shown in the diagram.
Ins Control Cable Lens Connector S/l6"(Approx1mately8mm)
Iris Control Cable
@. Cut off inner cable covers of the iris control cable as shown in the diagram.
li4"(Approximatly6mm)
6. Put the heat shnnkable tubes oreauivalenttubes on the innercables of the iriscontmlcable.
-
@. Solderthe inner cablesof the iriscontrol cableat the piin-plug block according to the following
1
piassignmentand coverthe heat shrinkabletubes or equivalenttubes over the solderedma
I
and heat on the tubes to shrink them.
n
I Signal for Video-iris lens I
I Signal for DC-iris lens 1
I Pi ]:Power source:t9V DC, 50mA Max. Pin I:DAMP-
Pi 2:N.C(Not used) Pi 2:DAMP+
Pin 3:Video Signal:0.7Vp-p/lOKohms. Pi 3:DRVt
Pin 4:Shield, ground Pin 4:DRV-(GND)
Rlb
When Auto-iris lens 1s used. please select Pln3 ,
EIS. BLC.ALC switch to ALC posltion p'n' 4,
J
Pl"4
Pl"2
@ Both the connector cover and connector should be properly iterlocked
Shrinkable
Tubes
Connector
Note Cut off the nb on the connector
Cover
When the lrrs control cable 1s too
w
thsk, connector cover and connector
can not
be interlocked
@Automatic Light Conhol/Electronic Light Control Selector (ALC, E/S)
Let you selectthemode accnrding to the lens type used.
ALC:Select this modewhen an auto ins lens(AU31ens)ii used with this camera
E8:Select this mode when atixed iris lensor
1 ODC or V/D
1)C.Fc.lc.t.t DC ~f!ou ;ue u,t~igthe .tlito In, Itn, that require* n D€ dn\zugndl
\'11)1'0 Select \'in li!ou orc u.tn:thc .IUIO In, Ism that rcqutrc, :I \tdcodn\c \ty.tl
@ DCLevel
DCAuto Iris lens level adjustment