Super Gym SG8021MT User manual

SG8021MT Multi-Press Combo
Assembly Instructions

Table of contents
Important Safety Instructions-------------------------------------------------------- 1
Exploded View Diagram---------------------------------------------------------------- 2
Hardware List----------------------------------------------------------------------------- 3
Parts List----------------------------------------------------------------------------------- 5
Assembly instructions----------------------------------------------------------------- 6

1
Important Safety Instructions
Before beginning any fitness program, you should obtain a complete
physical examination from your physician. When using exercise equipment,
basic precautions should always be taken, including the following:
* Read all instructions before using the Multi-Press Combo. These
instructions are written to ensure your safety and to protect the unit.
* Do not allow children on or near the equipment.
* Use the equipment only for its intended purpose as described in this guide.
Do not use accessory attachments that are not recommended by the
manufacturer: such attachments might cause injuries.
* Wear proper exercise clothing and shoes for your workout----no loose
clothing.
* Be careful when getting on or off the equipment.
* Do not overexert yourself or work to exhaustion.
* If you feel any pain or abnormal symptoms, stop your workout immediately
and consult your physician.
* Never operate the unit when it has been dropped or damaged.
* Never drop or insert anything into any opening in the equipment.
* Always check the unit and its cables before each use. Make sure that all
fasteners and cables are secure and in good working condition.
* Frayed or worn cables can be dangerous and may cause injury.
Periodically check these cables for any indication of wear.
* Keep hands, limbs, loose clothing and long hair well out of the way of
moving parts.
* Do not attempt to lift more weight than you can control safely.
* Do not use the equipment outdoors.
* Read each step in the assembly instructions and follow the steps in
sequence. Do not skip ahead. If you skip ahead, you may learn later that
you have to disassemble and that you may have damaged
the equipment.
* Assemble and operate the equipment on a solid, level surface. Locate the
unit a few feet from walls or furniture to provide easy access. The Multi-
Press Combo is designed for your enjoyment. By following these
precautions and using common sense, you will have many safe and
pleasurable hours of healthful exercise with the equipment.
Personal Safety During Assembly
comportments

Multi-Press Combo
Exploded View Diagram
2

Hardware List
3
0 100
10 20 30 40 50 60 70 80 90 110 120 130 140 150
Inches
0123456
/
12
/
14 /
34 / 34 / 34 / 34 / 34 / 34
/
14 / 14 / 14 / 14 / 14
/
12 / 12 / 12 / 12 / 12
Millimeters

Hardware List
4
0 100
10 20 30 40 50 60 70 80 90 110 120 130 140 150
Inches
0123456
/
12
/
14 /
34 / 34 / 34 / 34 / 34 / 34
/
14 / 14 / 14 / 14 / 14
/
12 / 12 / 12 / 12 / 12
Millimeters

5
Parts List
Item No. Description QTY Item No. Description QTY
1 Main Upright 1 41 Long FOAM 2
2Seat Frame 1 42 Short FOAM 1
3 Support Base 1 43 Upper Shroud 2
4 Above Cross Brace 1 44 Plat Screw M8*8 6
5 Press Arm Support 1 45 Washerφ13*φ24*1.5 12
6 Cross Brace 2 46 Allen bolt M12*95 4
7 Press Arm 1 47 Nylon Locknut M12 6
8 Cam 1 48 Washerφ11*φ20*1.5 57
9 Foot Frame 1 49 Nylon Locknut M10 26
10 Back Pad Bracket 2 50 Bolt M10*180 1
11 Back Pad Support 1 51 Allen bolt M10*90 2
12 Seat Pad Support 1 52 Allen bolt M10*95 4
13 Pulley Bracket 1 53 Bolt M10*72 2
14 Back Pad 1 54 Allen bolt M10*70 2
15 Seat Pad 1 55 Allen bolt M10*50 5
16 Short Shaft 2 56 Washer φ6.6*φ18*1.6 2
17 Long Shaft 1 57 Washer φ9*φ22*1.6 10
18 Long Pop Pin 1 58 Allen Bolt M8*15 10
19 Adjustment Plate 1 59 Flathead Socket Cap Screw M10*12 2
20 Short Guide Rod 1 60 Guide Rod 2
21 Guide Block 2 61 Bronze Bushing 8
22 Seat Adjustment Plate 1 62 Pollow Block Bearing 2
23 Weight Shroud 1 63 Linear Bearing 2
24 Cam Bracket 1 64 Allen Bolt M6*75 2
25 Rubble 465PopPin 1
26 Weight Stack 2 66 Philip Bolt M6*15 12
27 Weight plate 19 67 Washer φ11*φ38*2 1
28 Weight Pin 1 68 Washer φ11*φ30*2 1
29 Pull rope 1 69 Grease 1
30 Cap ring φ32 370 Allen bolt M10*25 11
31 Long Cable 1 71 Stopper 3
32 Short Cable 1 72 Allen bolts M10*95 4
33 Foot Pad 4 73 Top Plate 1
34 Pulley 4.5" 5 74 Allen bolts M12*75 2
35 Philip Bolt M4*20 2 75 Allen Wrench S=4 1
36 Nylon Washer 2 76 Allen Wrench S=6 1
37 Plug 25*50 1 77 Bottle hollder 170*165.5*115 1
38 Plug 50*50 3 78 Phillips head screw M6*15 5
39 Plug 50*70 2 79 Allen bolts M10*72 8
40 Cap φ32 3

Assembly Instructions
Assembly of takes professional installers about 2
hours. If this is the first time you have assembled this type of equipment,
plan to spend more time. It is strongly recommended to assemble the
equipment by professional installers. You may find it quicker, safer, easier to
assemble this equipment with the help of a friend, as some of components
may be large, heavy or awkward to handle alone. It is important that you
assemble your product in a clean, clear, uncluttered area. This will enable
you to move around the product while you are fitting components and reduce
the possibility of injury during assembly.
As with any assembled part, proper alignment and adjustment is critical.
While tightening the fasteners, be sure to leave room for adjustments. Do
not fully tighten the fasteners until instructed to do so. Be careful to
assemble the components in the sequence presented in this guide.
the Multi-Press Combo
6

Step 1 Install The Sub_support Components
1. Attach the Cross Brace (#06) and Foot Frame(#09) and Cam Bracket(#24)
to Main Upright(#01) using:
four Allen bolts (#72) M10*95 four Allen bolts (#52) M10*75
eight Nylon Locknuts(#49) M10 sixteen Washer (#48) φ11*φ20*1.5
eight Allen bolts (#53) M10*72 eight Nylon Locknuts(#49) M10
sixteen Washer (#48) φ11*φ20*1.5
2. Attach the Seat Frame (#02) to Cross Brace (#06) and Foot Frame(#09)
and Cam Bracket(#24) using:
7

Step 2 Assemble The Seat Pad Support
and Back Pad Support
1. Attach the Linear Bearing (#63) to Short Guide Rod(#20) .
2. Attach the Seat Pad Support(#12)and Back Pad Support (#11) to Linear
Bearing (#63) using:
eight Philip Bolts (#66) M6*15 two Washers (#48) φ11*φ20*1.5
one Bolt (#50) M10*180 one Nylon Locknuts(#49) M10
our Plat Screws(#44) M8*8
3. Attach the Back Pad Bracket(#10)and Short Shaft (#16) to Back Pad
Support (#11) and Seat Frame (#02) using:
f
8

Step 3 Assemble The Press Arm
1. Attach the Pollow Block Bearing(#62)to Press Arm Support(#05).
2. Attach the Support Base(#03)to Seat Frame (#02) using:
two Allen bolts (#74) M12*75 four Washers (#45) φ13*φ24*1.5
two Nylon Locknuts(#47) M12
four Allen bolts (#46) M12*95 two Allen bolts (#54) M10*70
two Allen bolts (#51) M10*90 eight Washer (#48) φ11*φ20*1.5
eight Washer (#45) φ13*φ24*1.5 four Nylon Locknuts(#47) M12
four Nylon Locknuts(#49) M10
two Plat Screws(#44) M8*8
3. Attach the Press Arm Support(#05)and Above Cross Brace(#04)to Seat
Frame (#02) and Support Base(#03)using:
4. Attach the Press Arm(#07)and Long Shaft (#17)to Press Arm Support(#05)
using:
9

Step 4 Assemble The Weight Stack and Cam
1. Attach the Cam(#08)to Cam Bracket(#24)using:
one Allen bolt (#70) M10*25 one Washer (#67)φ11*φ38*2
one Allen bolt (#70) M10*25 one Washer (#68)φ11*φ30*2
two Bolts (#53) M10*72
2. Attach the Pulley Bracket(#13)and Nylon Washer (#36) to Main Upright
(#01) using:
3. Slide Weight Stack (#26) down onto rach the Guide Rod(#60).
4. Carefully begin sliding nineteen Weight Plates (#27)one by one .
5. Align the both ends of Guide rodes(#60) to the Main Upright(#01) and
secure using:
10

Step 5 Route Cable
1. Screw Weight Pin(#29) to Top Plate(#73).
2. Route the Long Cable(#31) and Short Cable(#32) using:
five Allen bolts (#55) M10*50 ten Washers (#48) φ11*φ20*1.5
five Nylon Locknuts(#49) M10 two Philip Bolts(#35) M4*20
11

Step 6 Assemble Pads and Shroud
1. Attach two Upper Shrouds(#43) and Weight Shroud(#23) to Main Upright
(#01) using:
ten Allen bolts(#58) M8*15 ten Washers (#57)φ9*φ22*1.6
four Allen bolts (#70) M10*25 four Washer (#48) φ11*φ20*1.5
four Allen bolts (#70) M10*25 four Washers (#48) φ11*φ20*1.5
two Philip Bolts(#78) M6*15
2. Attach the Back Pad (#14) to Back Pad Support (#11) using:
3. Attach the Seat Pad (#15) to Seat Pad Support (#12) using:
4. Attach the Bottle hollder (#77) to the Main Upright(#01) using:
12