superbrightleds DMX-4CH-6A User manual

DMX-4CH-6A
DMX Decoder
Product Features
Meets DMX512/1990,RDM /2009 protocol
Supported RDM parameters:
DISC_UNIQUE_BRANCH
DISC_MUTE
DISC_UN_MUTE
DEVICE_INFO
SOFTWARE_VERSION_LABEL
DMX512/RDM_START_ADDRESS
IDENTIFY_DEVICE
MANUFACTURER_LABEL
SUPPORTED_PARAMETERS
In DMX mode set the DMX address manually by switch; in RDM mode, the host computer address allocation
3 or 4 Channels optional by DIP switch 10
Constant voltage output, the maximum current of 6A /ch for RGBW decoder and 8A/ch for RGB decoder
Screw terminals for input/output ports& RJ45 and XLR-3 Interface for DMX512/RDM signal ports
256 level brightness adjustment
DMX-4CH-6A User Manual V01.1 1

Technical Specifications
Model
DMX-4CH-6A
Channels
1-4
Output
Voltage
12-24VDC
Current
6A *4ch or 8A*3ch
Power
288W(12V)/576W(24V)
Voltage
12-24VDC
Input
Standby loss
＜1W
Control signal
DMX512 1990 /RDM 2009
Dimension
125*54*41mm（L*W*H）
G.W. 344g (12.13oz.)
Operational temperature
-20-50℃
Relative humidity
20%-90%RH
Dimensions
DMX SIGNAL INTERFACE
2
1: GND
2: DATA-
3: DATA+

Interface Introduction
Connection & Setup:
Connect the anode and RGBW wire of common anode RGBW LED light to the output interface of decoder
directly; Connect the anode wire of single-color LED light to V+ on decoder, and connect the cathode wire to one
of RGBW pin according to the LED's color; Connect several colors single-color LED lights to one decoder, please
connect their anode wires to V+ pin on decoder.
DIP Switch Setting
DIP1 DIP2 DIP3 DIP4 DIP5 DIP6 DIP7 DIP8 DIP9 DIP10
OFF 0 0 0 0 0 0 0 0 0 3Addr
ON 1 2 4 8 16 32 64 128 256 4Addr
DIP1~9: Setting the first DMX address of device，the sum of number showed in the table above is the first DMX
address of device.
In DMX mode, the effective address is 1-511, and 507-511 is for fixed mode (507 means output static red; 508
means output static green; 509 means output static blue; 510 means output static white; 511 means output RGB or
RGBW gradient).
When the address is 0, the default is RDM mode.
DIP10 is used to select the address mode. “ON” is 4 channels, “OFF” is 3 channels.
DMX-4CH-6A User Manual V01.1 3
123456
(2)XLR-3 DMX512/RDM signal input interface
(4)Power input interface
(6) Address setting interface
(1) RJ45 Signal input and output interfaces
(3) XLR-3 DMX512/RDM signal output interface
(5) Driver output interface

Wiring Diagram
1) Use the CAT-5 cable or three-core shielded cable as DMX512/RDM signal cable，and DMX512/RDM signal has
the positive and negative signal. When connecting the DMX512/RDM signal cable plug, please pay attention to
distinguish between positive (+) and negative (-), and then connect the DMX512/RDM signal cable with the
corresponding input interface of decoder correctly.
2) Connect a signal terminator plug at the end of the DMX link.
DMX-4CH-6A User Manual V01.1 4