SuperCloset SUPERROOM User manual

INSTRUCTION MANUAL
SUPERROOM
5x5 LED

WELCOME TO THE FAMILY
Congratulations, and thank you for choosing SuperCloset.
You now have the world's best grow room.
These instructions will guide you through the process of
setting up your SuperRoom. Please read through the entire
instruction manual before you begin, including any and all
instructions that come with the individual components.
Lets take a look at the layout and components of your SuperRoom.
GORILLA GROW TENT
CARBON AIR FILTER
KIND LED
GROW LIGHT
INTERNAL
CIRCULATION FAN
GROWING
SYSTEM
(HYDROPONIC OR SOIL)
TOOL POUCH
1FT EXTENSION

GETTING READY
1
2
3
Unpack the pallet and boxes that your SuperRoom
came in and lay out in an organized pile.
Once all items are unpacked, reference your quality
assurance checklist to verify that you have all the
contents of your SuperRoom.
Make sure you have planned accordingly to ensure
you have the proper amount of power and properly
sized breakers going to your SuperRoom. Always
consult a professional electrician when setting up and
planning your electrical configuration.
Let’s start with unpacking the SuperCloset...
Prior to setup, make sure you have all of the necessary components by cross
referencing the QAC (Quality Assurance Checklist). Take this time to familiarize
yourself with each of the components.

If you have any questions during the setup process, please call a SuperCloset representative at 1.877.476.9787
Make sure you assemble the tent in its final location, as it will be difficult to
move when fully assembled. We will not be plugging in any of the
components just yet. Let’s get everything in place first.
1. Assemble your Gorilla Grow Tent according to the manufactures included
setup instructions (image a). Determine ahead of time if you are able to
assemble as a standard 6’ 11” tall tent, or if you are able to maximize your
space and go with the 7’ 11” tall configuration.
2. Once your tent is assembled, double check to make sure that all fittings are
installed properly including your ceiling support poles (image b).
We are now ready to set up the SuperRoom
Gorilla Grow Tent set up
Use masking tape and a marker to label the power cords of your
components at the plug to help identify your components later in
the assembly.
SUPER GROW TIP:
a
b
1’EXTENSION
NOEXTENSION
7’11”
6’11”

If you have any questions during the setup process, please call a SuperCloset representative at 1.877.476.9787
1. Locate the carbon filter (image a). Slide on the pre-filter and secure with
included elastic bands.
2. Locate and unpack the inline fan (image b).
3. Attach the mounting bracket and hang the inline fan from the roof support
crossmember (image d) and secure with zip tie.
4. Locate the two black filter hanging straps. Loop the straps around the roof
support crossmember (image e). Slide the carbon filter through the loops and
tighten securely (image f).
4. Position the carbon filter over the end of the inline fan and secure with
included duct tape (image g).
5. Locate the ducting and hose clamp. Slide the hose clamp over the end of the
ducting and attach the ducting to the open end of the inline fan (image h).
Tighten the hose clamp securely and feed the open end of the ducting through
the desired ducting port (image i). Tighten the dual-cinching ports around the
ducting when done.
1. Locate Carbon Filter (image a). Using the black straps (image b) included
with the Gorilla Grow Tent, attach the filter to the celing support on the back
wall of the tent (image c & d).
2. Locate the ducting and hose clamps included in your system. Slide the
hose clamp over the ducting prior to attaching the ducting to the filter
(image e). Attach one end of the ducting to the filter using the provided
hose clamps and tighten for a snug fit (image f).
3. Feed the other end of the ducting through the nearest port hole (image h).
Once the ducting is fed throught the hole, use the double-cinching pulls to
tighten the port around the ducting to prevent any light leaks.
4. Locate the inline fan included with your system (image g).
5. Slide the hose clamp on the the open end of the ducting and attach the
ducting to the FLAT side of the fan (image i) and tighten for a snug fit
(image j).
Hanging Carbon Filter and Inline Fan
The inline fan will be pulling air from inside the tent, through the carbon filter,
ensuring the air leaving the tent is free of odors and aromas. It is important to note
the direction of the fan’s airflow when installing (image c).
NOTE:
AIR FLOW
a
b
c
d e f
i
gh

If you have any questions during the setup process, please call a SuperCloset representative at 1.877.476.9787
The Inline Fan will be pulling air from inside the tent, through the Carbon Filter,
ensuring that your exhaust is free of odors and aromas.
Carbon Filter & Fan Diagram
CARBON
FILTER
INLINE
FAN
DUCTING
AIR FLOW
AIR FLOW
CARBON
FILTER
INLINE
FAN
DUCTING
SET UP OPTION 1
SET UP OPTION 2

If you have any questions during the setup process, please call a SuperCloset representative at 1.877.476.9787
1. Locate your Yo-Yo light hangers (image a).
2. Loop the carabiner end over the top support of the tent and clip it to itself
(image b). To adjust height, pull on the lose string to raise the Yo-Yo or
press the button on the side of the Yo-Yo hanger to lower.
3. Unpack your KIND LED Grow Light(s).
4. Locate your the Wire Hangers (image c). Connect the wire hangers to
each of the metal hangers on the light (image d).
5. Place the Kind LED Light in the bottom of the tent. Lower the Yo-Yo
system until you can connect the other ends of the cable assemblies to the
Yo-Yo carabiners (image e). Raise the light to the desired height using the
loose end of the Yo-Yo hanger cord.
6. Run the power cord from the LED light through the nearest electrical port
hole.
Hanging your LED Light
1.Locate the Thermometer/Hydrometer (image e). Remove the battery cover
and remove the plastic safety blocker from the battery terminal. You can
be creative on where you would like this placed inside the tent, but the
easiest placement is inside the tool pouch on the inside of the tent.
2.Run the external probe to the outside of the tent, through the nearest
ducting port. Make sure the probe is not touching any surface on the
outside of the tent as this will provide false readings.
3.Locate the Clip-On Active Air Fan (image f). Clip the fan to any one of the
inside corner vertical poles. The fan is designed to provide circulation and
air movement.
Thermometer/Hydrometer/ICF
a
b
c
d
ef

If you have any questions during the setup process, please call a SuperCloset representative at 1.877.476.9787
Thoroughly read and follow the instructions included with your chosen grow system. If
you opted for the soil method, simply arrange the included pots and plastic trays in an
orderly manner.
Grow System set up
Super Flow
Soil Pots
Bubble Flow Buckets
Make sure you have installed the spill tray
included with your Gorilla Grow Tent prior to
setting up the grow system in your tent
The Reservoir for the Bubble Flow Buckets is
placed on the outside of the tent. This will
help to keep the water at a desirable
temperature and allow you access to the
Reservoir without disturbing your grow
environment. This arrangement may require
notching small openings for your fill and
drain lines to pass through the wall of the
tent. For proper operation of the Bubble Flow
Buckets, all drain lines must be completely
level from the buckets to the Reservoir to
ensure proper draining.
NOTE:

If you have any questions during the setup process, please call a SuperCloset representative at 1.877.476.9787
1. Locate the power strip (image a), the GFCI Protector (image b), the Smart
Plug(s) (image c), the 3-IN-1 adapter (image d), and the inline fan controller
(image e).
DO NOT PLUG IN THE POWER STRIP YET.
2. Plug in the following from left to right:
Properly configured Power Strip Should look like this
1) Inline Fan
2) Internal Circulation Fan
Plug the 3-IN-1 adapter in the far plug on the power strip
3) Plug the first Smart Plug in and then the Kind LED
light into the Smart Plug
4) Air Pump (Hydro Only)
5) Plug the second Smart Plug in and then the Water
Pump into the Smart Plug (Hydro Only)
Final Assembly
KIND LED
LIGHT
INLINE
FAN
AIR PUMP
(Hydro Only)
WATER PUMP
(Hydro Only)
INTERNAL
CIRCULATION FAN
a
b
c
d
e

If you have any questions during the setup process, please call a SuperCloset representative at 1.877.476.9787
1. Plug the GFCI Protector (image a) into any 110v wall socket. With the power
strip turned OFF, plug the power strip into the GFCI Protector.
DO NOT POWER UP YOUR SUPERROOM YET!
2. Now that everything is plugged into the power strip, lets verify some
important steps:
3. After verifying all of the above, it’s time to turn on your SuperRoom. Turn the
power strip switch to the ON position, and the system should spring to life
before your very eyes!
1) LED Light is properly hung.
2) Watering System tube is securely fastened to the top of the Water Pump. (Hydro Only)
3) Reservoir is filled with water and Water Pump is fully submerged. (Hydro Only)
4) Air Pump is next to (NOT IN!) the reservoir. (Hydro Only)
5) Light Power Cord is plugged into Smart Plug#1.
6) Water Pump Power Cord is plugged into Smart Plug #2. (Hydro Only)
7) Power Strip is off and plugged into the GFCI Protector.
Almost Done
NOTE:
a