SuperCloset SUPERSTAR User manual

INSTRUCTION MANUAL
SUPERSTAR
SMART GROW CABINET
LED

WELCOME TO THE FAMILY
TOTAL
GERMINATION KIT
SUPERCLONER
CARBON AIR FILTERS
GROW LIGHT
HYGROMETER
INTERNAL
CIRCULATION
FAN
GROWING
SYSTEM
(HYDROPONIC OR SOIL)
Congratulations, and thank you for choosing SuperCloset.
You now have the world's best grow cabinet.
These instructions will guide you through the process of
setting up your SuperStar. Please read through the entire
instruction manual before you begin, including any and all
instructions that come with the individual components.
Lets take a look at the layout and components of your SuperCloset.

COMPONENTS
CARBON AIR FILTER KIND LED LIGHT POWER STRIP AIR PUMP WATER PUMP
INTERNAL CIRCULATION FAN SUPERPONICS 8 SOIL POTS SOIL POT TRAY 1/4” AIR TUBE HOSE
AIR STONES 3” & 2” NET CUPS LOTUS NUTRIENTS SAMPLES Ph TESTING KIT
GFCI THERMOMETER/
HYGROMETER TDS METER NET TRELLIS, HOOKS, TIES
3-1 ADAPTER
T5 LIGHT 3” ELBOW
2” ELBOW
1½” ELBOW W/ EXTENSION
CLAY ROCKS 1” GROW PLUGS SUPERCLONER 14
SMART PLUG
OR
X2
X2 X3 X2
X4X2
X2
X2 X2
X2
X4X4

GETTING READY
1
2
3
Carefully unbox your SuperCloset and remove all
contents from inside the cabinet.
Unpack the contents of the cabinet, as well as any
components packaged inside the cabinet reservoir.
Reference your Quality Assurance Checklist and
verify that you have all of the needed components
for your system.
Let’s start with unpacking the SuperCloset...
Prior to setup, make sure you have all of the necessary components by cross
referencing with the QAC (Quality Assurance Checklist). Take this time to
familiarize yourself with each of the components.

If you have any questions during the setup process, please call a SuperCloset representative at 1.877.476.9787
1. Make sure the cabinet is in its final location, as it will be more difficult to move
when fully assembled. We will not be plugging in any of the components just
yet. Let’s get everything in place first.
2. Your cabinet comes with 5 Black Plastic Elbows (image a). You will have two
2” Elbows with foam tape down the middle, one 1.5” Elbows with Foam Tape
and two 3” with Foam Tape and Extensions for bottom corners.
3. The exterior Elbows will allow you to run your cords out of your cabinet with
minimal light leaks and allow for fresh air flow into your cabinet. The interior
Elbow will facilitate airflow between the Cloning Chamber and the
Veggie/Flower Chamber (image b).
4. Locate your Power Strip (image c). Locate the two screws on the center rear
of the cabinet. Your power strip has holes on it that fit on these screws for
mounting (image d).
a. Insert the foam side of the two 3” Elbows into large holes
located at the bottom corners in rear of the cabinet.
b. Insert the 1.5” Elbow into the hole located in the interior and
on front your shelf.
c. Insert the two 2” Elbows in the center holes located at the top
and center at back of cabinet.
We are now ready to set up the SuperCloset
Use masking tape and a marker to label the power cords of your
components at the plug to help identify your components later in
the assembly.
SUPER GROW TIP:
a
b
c
d
X2
X2

If you have any questions during the setup process, please call a SuperCloset representative at 1.877.476.9787
1. Locate and unpack your Custom Carbon Filters (image a).
2. Remove the four wing nuts on the back side of the fan (image b), then
remove the fan grill from the fan.
3. Locate the large opening in the back of the cabinet with the four small
surrounding holes (image C). With the help of a partner hold the Carbon
Filter and fan flush to the inside back of the cabinet. Make sure to place the
four bolts through the four provided holes. The power cord remains inside
the cabinet NOT THROUGH THE FAN HOLE OPENING.
4. Have a partner place the fan grill on the outside of the cabinet on the four
filter fan bolts, then tighten the wing nuts onto the exposed bolts (image d).
Repeat steps 1-4 for both Carbon Filter/Fans.
5. Run the power cords for your Carbon Filter Fans through the nearest Elbow
to the back of the cabinet.
Installing your Custom Carbon Filters a
b
c
d

If you have any questions during the setup process, please call a SuperCloset representative at 1.877.476.9787
Hanging your LED Light
1. Unpack KIND LED Grow Light (image a).
2. Locate your the Wire Hangers (image b).
3. Connect the wire hangers to each of the metal hangers on the light
(image c).
We have set the light on a convenient Yo-Yo system so the height can be
adjusted as your plants grow. To lower the light, simply press the button
located on the side of the Yo-Yo and adjust to the desired height. To raise
the light pull upward on the end of the Yo-Yo cord.
4. Place the Kind LED Light in the bottom of the cabinet. Lower the Yo-Yo
system until you can connect the Yo-Yo carabiners to the center of the
Wire Hangers (image d). Raise the light to the desired height.
5. Run the power cord from the LED light through the nearest Elbow opening
to the back of the cabinet.
a
b
c
d

If you have any questions during the setup process, please call a SuperCloset representative at 1.877.476.9787
4. Locate and unpack two of the bubble wrapped T5 Light Strips located in your
package (image a). Use the short “daisy chain” connector found inside the
light packaging to connect the two T5 lights to one another (image b). Then
attach one power cord to the end of one of the T5 lights.
5. The T5s comes equipped with magnetic backing and is mounted to the
underside ceiling of the cloning chamber (upper chamber) in this manner
(image c).
6. Locate the Internal Circulation Fan (image d). Note the “S” hook connected
to the base of the Fan. This hook will fit into the notches located on the
backside of the inner door frame (image e). Mount the Fan on one of the
lower notches. As your plants grow taller, move the Fan to the upper
notches. Ideally the Fan will blow air across the top of the plants. Thread
cord through the upper hole found on the lower interior of the cabinet (same
as the Light power cord).
7. Locate the Thermometer/Hygrometer (image f). Remove the battery cover
and remove the plastic safety blocker from the battery terminal. Use the
included Velcro Strips to affix your Thermometer/Hygrometer to the inside of
your cabinet. The best placement for this is towards the top of the cabinet,
either on the side or back wall.
8. Run the external probe to the outside of the cabinet, through the nearest
Elbow. Make sure the probe is not touching any surface on the out side of
the cabinet as this will provide false readings.
Setting up the SuperCloset a
b
c
d
e
X2

If you have any questions during the setup process, please call a SuperCloset representative at 1.877.476.9787
1. Locate your SuperCloner14 (image a). Remove lid, and set aside. Remove
all contents, including the Air Pump, the blue 8” Air Stones, and fourteen
Net Cups.
2. Unwrap the Air Stones and lay them down inside of the SuperCloner
(image b).
3. Locate your Air Pump (image c) and place it next to the SuperCloner.
THIS PUMP SHOULD NEVER BE PLACED IN WATER!
4. Locate and attach the two black tubes (image d) to the metal nodes on the
front of the Air Pump. Run the other end of the black tubing through the
channels located on the rim of the reservoir (image e).
5. Connect the other end of the black tubing to the Air Stones. Once these
two pieces are connected, ensure the Air Stones remain flat on the floor of
the reservoir.
6. Turn the black dial on top of your Air Pump clockwise until it stops.
Replace the lid of the SuperCloner and position in the Cloning Chamber
along with the Air Pump into the cloning chamber. Run the Air Pump
Power Cord out of the cabinet through the same Elbow through which you
ran the T5 Light Strip Power Cord. Do not plug in the Air Pump yet.
7. Insert the 2” net cups.
SuperCloner 14 Assembly
NOTE:
a
b
c
d
e

If you have any questions during the setup process, please call a SuperCloset representative at 1.877.476.9787
1. Remove the lid from the SuperPonic 8 system and set it aside for now.
Notice the channels located on the rim of the reservoir (image a). These
channels will be for the placement of your Air Pump Tubing and Water
Pump power cord.
AIR PUMP AND AIR STONES
2. Locate the two gray Air Stones included in your shipment. Place the Air
Stones at the bottom of the SuperPonics reservoir (image b). Note: the
airtstones have a male end that will fit in the black Air Pump tubing.
3. Connect the Air Pump tubing to the end of the airstones. Arrange the
tubing into the channels located on rim of the reservoir (image c).
4. Locate the Air Pump included in your shipment (image d).
THIS PUMP SHOULD NEVER BE PLACED IN WATER
5. Locate the black tubing from the Air Stones and connect the open end to
the metallic outputs located on the Air Pump (image e).
6. Now we can run our Air Pump power cord through the lower opening in the
back of the cabinet.
SuperPonic 8 System Assembly
Your plant roots need and love oxygen! It is extremely important
to the health of the plants that you keep your Air Pump and Air
Stones running at all times when the system is in use.
SUPER GROW TIP:
NOTE:
a
b
c
d
e

If you have any questions during the setup process, please call a SuperCloset representative at 1.877.476.9787
7. Locate the Water Pump (image a). Place the Water Pump in the center of
the SuperPonics reservoir. Arrange the power cord of the Water Pump into
the channel located on the rim of the reservoir (image b).
8. Locate the reservoir lid. On the under side of the lid, locate the open end
of the black tubing (image c). Attach the open end of the tubing to the
open connector on the top of the Water Pump (image d). Return the lid to
the reservoir.
9. Run the Water Pump power cord through the lower opening in the back of
the cabinet. Use the same opening in which we ran the power cord for the
Air Pump.
10. Now we can place our Net Cups into the openings of the top of the
reservoir. Once in place, arrange the top feed hoses to the center of the
net cups.
11. Notice the length of tubing located on the top side of the reservoir lid
(image e) This is your Reservoir Drainage Tube. By opening the valve
(turning parallel to the tube) and turning the pump on, you can easily drain
your reservoir. See (image e) for on/off positions.
12. Place the SuperPonics system and Air Pump inside the cabinet with the
Drainage Tube towards the front.
Read the instructions for the water pump, as they
contain valuable information on how to maintain this
component. THIS PUMP SHOULD NEVER RUN WHEN
NOT FULLY SUBMERGED IN WATER.
SuperPonic 8 System Assembly
NOTE:
OPEN CLOSED
a
b
c
d
e

If you have any questions during the setup process, please call a SuperCloset representative at 1.877.476.9787
1. Locate the power strip (image a), the GFCI Protector (image b), the two
Smart Plugs (image c), and the 3-IN-1 adapter (image d).
DO NOT PLUG IN THE POWER STRIP YET.
2. Plug in the following from left to right
TOP ROW
1) Smart Plug #1
Once the Smart Plug is plugged in, plug in the Kind LED
Grow Light
2) Internal Circulation Fan
3) T5 Clone Chamber
4) Smart Plug #2
Once this Smart Plug is plugged in, plug in the 3-in-1
Adapter with the following.
- Water Pump #1
- Water Pump #2
BOTTOM ROW
5) Air Pump #1
6) Air Pump #2
7) Air Pump #3
8) Carbon Filter Fan #1
9) Carbon Filter Fan #2
Final Assembly
KIND LED LIGHT T5 CLONE CHAMBER
CARBON
FILTER FAN #2
AIR PUMP
#2
WATER PUMPS
INTERNAL
CIRCULATION FAN
AIR PUMP
#3
AIR PUMP
#1
CARBON
FILTER FAN #1
Properly configured Power Strip Should look like this
a
b
c
d
X2
X1

If you have any questions during the setup process, please call a SuperCloset representative at 1.877.476.9787
3. At this time, add water to the reservoirs. When filled to the appropriate
levels, the SuperCloner 14 reservoir will hold about 1.5 -2 gallons of water.
The SuperPonic 8 reservoir will hold about 2-3 gallons.
Almost Done
4. Plug the GFCI Protector (image b) into any 110v wall socket. With the power
strip turned OFF, plug the power strip into the GFCI Protector.
DO NOT POWER UP YOUR CABINET YET!
5. Now that everything is plugged into the power strip, lets verify some
important steps:
6. After verifying all of the above, it’s time to turn on your SuperCloset. Turn the
power strip switch to the ON position, and the system should spring to life
before your very eyes!
1) LED Light is properly hung.
2) Watering System tubes are securely fastened to the top of the Water Pump.
3) Both Reservoirs are filled with water and Water Pump is fully submerged.
4) Air Pumps are next to (NOT IN!) the reservoir.
5) Light Power Cord is plugged into Smart Plug#1.
6) Water Pump Power Cords are plugged into Smart Plug #2.
7) Power Strip is off and plugged into the GFCI Protector.
Your reservoir should always be filled at least halfway. In the
beginning stages, we recommend maintaining a water level
extremely close (½” - 1”) from the bottom of the net cups, but not
touching (image a). The water should remain at this level until an
evident root structure begins to develop.
SUPER GROW TIP:
NOTE:
EARLY STAGE
12:00 - 12:03
4:00 - 4:03
8:00 - 8:03
12:00 - 12:03
4:00 - 4:03
8:00 - 8:03
Water pump schedule suggestions.
Run for 3 minutes approximately every 4 hours.
a
b