Superfront BRUTA WALL 1/2 User manual

Mounting instructions BRUTA WALL 1/2
1. Mount the frame on the wall.
Mount your Ikea frames on the wall with the Ikea
suspension rail before mounting your parts from
Superfront.
Mounting
2. Clean the surfaces.
Use the aached 3M wet wipe to clean the surfaces
of the cabinet and the Superfront sides and top.
3. Aach the MountPads on the frame.
Once the frames are mounted on the wall, aach the
smaller of the supplied MountPads to each corner of the
top of the frames. Place them inside the edge of the side
of the frame and about 1 cm from the front and back of
the frame.
NOTE! Do not remove the cover paper from
the MountPads yet!
Finished result
The result varies depending
on the size of the frame.
Superfront /+46868441814 / [e-mail] / www.superfront.com
FRONTSIDA
TOP
Content 3M wet wipe
3M
VHB™
GB Surface Cleaner Sachet
Foruse with 3M™ VHB™ Tapes
FR Pochee de Neoyage
A utiliser avec les rubans 3M™ VHB™
DE Reinigungstuch
Für den Einsatz mit 3M™ VHB™
MountPads 10x10mm & 40x25mm
(the number varies)
Screw 23 mm
(the number varies)
Distribution of MountPads.
Here's how the MountPads should be
distributed on the frames.
(The number varies depending on the number of frames)
Be sure to always follow the safety instructions that apply to your furniture. Always secure the cabinet to the wall. This also applies to low cabinets where the weight
distribution changes drastically when the fronts open. Especially in the case of solid quality fronts as ours. Use the anchor brackets supplied with the Ikea cabinet.
Safety!

5. Mount the sides (B) in place.
Do this step first without removing the cover paper on
the MountPads so that you get the hang of it before
you do it for real. The friend continues to help.
Place the side (B) as shown below. NOTE! Make sure the
back of the side is flush with the wall and in line with
the top edge of the top panel.
Slowly tilt the side inwards until it touches the Mount-
Pads. Make sure that it ends up in the right position.
NOTE! If you are going to have a cover panel on the
underside of the wall cabinets, tilt this in place as well.
You and your friend are good at this now!
Mounting instructions BRUTA WALL 2/2
PRESS HARD OVER EACH MOUNTPAD FOR AT LEAST 30
SECONDS. This is important because the adhesive in
our MountPads cure under pressure.
4. Mount the top (A) in place.
Do this step first without removing the cover paper on
the MountPads so that you get the hang of it before
you do it for real. Here it is good to get help from a
friend.
Place the top (A) as shown below. NOTE! Make sure
that the back of the top is flush with the wall and that
it is centred.
Slowly tilt the top downwards until it touches the
MountPads. Make sure that it ends up in the right
position.
Superfront /+46868441814 / [e-mail] / www.superfront.com
7. Mount the doors.
Follow the instructions that come with the hinges from
Ikea. Don't forget to adjust how the doors hang using
the three screws on the hinges. It takes some patience
but is worth it – we promise!
Screw 23 mm
(the number varies)
A
6. Drive the screws.
These screws work as additional support. Press on the
outside of the side at the point where you drive the
screw. Spread the screws as evenly as possible without
them being in the way of the hinges or shelf supports.
PRESS HARD OVER EACH MOUNTPAD FOR AT LEAST 30
SECONDS. This is important because the adhesive in
our MountPads cure under pressure.
MAKE SURE THE SIDE'S EDGE
IS ALIGNED WITH THE TOP.
B
5. Mount the sides (B) in place.
Continue.
Note! Avoid having open sawed ends near wet areas. A lacquered surface is best but if that is not possible be sure to seal the sawn part using paint or silicone.