SUR&R PFT409 User manual
INCLUDED IN KIT
PART NO. DESCRIPTION PART NO. DESCRIPTION
PFT205 Die – 3/16” (4.75 mm) 45° & DIN PFT340 Punch – 5/16” (8 mm) DIN
PFT210 Die – 1/4” 45° & DIN PFT350 Punch – 3/16” & 1/4” 45° OP2
PFT215 Die – 5/16” (8 mm) 45° & DIN PFT355 Punch – 5/16” x 3/8” 45° OP2
PFT220 Die – 3/8” 45° PFT383 Punch – OP0
PFT305 Punch – 3/16” (4.75 mm) 45° OP1 PFT610 PFT409 Yoke Set Screw Handle
PFT310 Punch – 1/4” 45° OP1 PFT615 PFT409 Yoke
PFT315 Punch – 5/16” (8 mm) 45° OP1 PFT620 PFT409 Yoke Handle
PFT320 Punch – 3/8” 45° OP1 PFT625 PFT409 Hydraulic Handle
PFT330 Punch – 3/16” (4.75 mm) DIN PFT630 PFT409 Case
PFT335 Punch – 1/4” DIN
OPTIONAL (Sold Separately)
PART NO. DESCRIPTION PART NO. DESCRIPTION
PFT245 Die – 3/16” (4.75 mm) 37° PFT260 Die – 3/8” 37°
PFT250 Die – 1/4” 37° PFT325 Punch – 3/16” (4.75 mm) 37° OP2
PFT255 Die – 5/16” 37°
DIES
INCLUDED OPTIONAL
PFT205 PFT245
PFT210 PFT250
PFT215 PFT255
PFT220 PFT260
PUNCHES
INCLUDED
PFT305 PFT335
PFT310 PFT340
PFT315 PFT350
PFT320 PFT355
PFT330 PFT383
OPTIONAL
PFT325
Rev 1 9/21
1. Make sure tubing end is cut
straight and deburred.
2. Install handle into threaded hole
in bottom of yoke. (Fig. 1)
3. Select die set which corresponds
to desired flare.
4. Install die set vertically into yoke,
such that the interface between
the two halves is visible. (Fig. 2)
5. Position tubing flush with end of
die set. (Fig. 3)
6. Install set screw handle and
tighten set screw to press die
halves together and hold tubing
firmly in place. (Fig. 4)
7. Select punch that corresponds to
desired flare.
8. Slide punch into chuck end of
tool. (Fig. 5)
9. Insert tool into groove in yoke.
Ensure punch is aligned with
center axis of tube. (Fig. 6)
10. Holding yoke with handle, hold
pistol grip with other hand and
pull lever to press punch into die.
Continue to pull and release lever
until movement stops. (Fig. 7)
11. Press lever on rear of tool to
retract punch out of tube. (Fig. 8)
Flare is complete. (Fig. 9)
PFT409 Pistol Grip Flaring Tool Instructions
12. If creating a double flare,
insert cone-shaped punch
corresponding to tube size
into chuck end and repeat
steps 9 through 11. (Fig. 10)
1
3
5
7
9
2
4
6
8
10
S.U.R.&R. AUTO PARTS INC. • 2325 HUSKY WAY • PACIFIC, MO 63069
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
9001:2015
CERTIFIED
COMPANY
