Swift CRUZE SDB-CVTB0970 User manual

FITTING INSTRUCTIONS
VERTICAL BLINDS

YOU SHOULD HAVE
TOOLS REQUIRED
• Screwdriver
• Pencil
• Power-Drill
• Tape Measure
• Pliers
BRACKETS
SAFETY DEVICES
• Tie down Safety Clip
CHILDREN CAN
STRANGLE IF A
SAFETY DEVICE IS NOT
INSTALLED. ALWAYS
USE A SAFETY DEVICE
TO KEEP CORDS AND
CHAINS OUT OF REACH
OF CHILDREN.
Fixing Holes
STEP 1
THE INSTALLATION OF THIS
PRODUCT SHOULD BE
CONDUCTED BY SOMEONE
COMPETENT IN DIY.
OUTSIDE RECESS
If the blind is to be fitted
outside the window ensure that
measurement C is the same.
Follow instructions for FACE
FIXING. To calculate C=(A-B)/2.
INSIDE RECESS
TOP FIX to the lintel or FACE FIX
brackets to the window frame.
STEP 2
TOP FIXING
Measure and mark the distance
(D), allowing for obstructions like
handles that protrude into the recess
area. Hold each bracket into place
and mark the hole positions. Fit
each bracket using suitable screws.
Please ensure fixings are suitable for
the wall/surface to which you are
mounting the brackets.
FACE FIXING
Position brackets approx 5cm from
the ends of where the headrail
is to be positioned. If more than
2 brackets are supplied, fit the
additional brackets at equal spacing
across the length of the blind.
Please ensure fixings are suitable
for the wall/surface to which you
are mounting the brackets.
(D)
(A) Width of Blind
(B) Top Fix
(C)(C)

STEP 5
TOP FIXING
Tilt and hook headrail into bracket
at point (E). Rotate the headrail into
position until it clicks. To release the
headrail push the bracket at point (F)
SAFETY DEVICE
The safety device must be installed at
the maximum distance possible from
the control mechanism to prevent
looped chain becoming slack. Place
the safety device on the wall and
mark the positioning of the 1 screw
hole. Drill holes using a suitable
drill bit. Place device into position
ensuring the chain is fully taut.
RETAINING DEVICE
Screw the retaining device using
suitable fixings ensuring the device
is fully closed.
FACE FIXING
Hook the back of the headrail
into the bracket and rotate the
headrail into position. Secure
headrail by tightening the short
screw in the front of the bracket.
STEP 3 STEP 4
(E)
(F)
Short screw
ATTACHING
VERTICAL VANE
With the headrail fitted,
hook each fabric slat into
the headrail travellers
ensuring the traveller pegs
are in the open position.
BOTTOM WEIGHTS
Insert the bottom weights
into the vertical vane
bottom pockets.
STABILISING CHAIN
Push connector on
stabilising chain onto
the ear of each bottom
weight. Stabilising chain
should be connected to
both sides of the blind.
STEP 6 STEP 7
Tilt and hook headrail into front of
the bracket. Rotate the back of the
headrail into position until it clicks.
To release the headrail push the spring
clip towards wall and release at front.
MAX DISTANCE POSSIBLE
(ensuring chain is fully taut.)

STEP 1
TRAVELLERS NOT ALIGNED
LOUVRE BLIND TROUBLESHOOTING
Pull on chain until
completely restricted.
At this point you will need to pull on
the chain with force. You will hear a
grinding noise - this is normal.
STEP 2 STEP 3
Travellers should start to align.
STEP 4
Repeat step 2 pulling chain in the
opposite direction until travellers
are fully aligned.
STEP 5
Did this align all the pegs? If not, gently rotate the lazy traveller with a pair
of pliers. The traveller will then click into place accordingly.

WHEN I PULL THE CONTROL CHAIN THE LOUVRES WON’T TURN
LOUVRE BLIND TROUBLESHOOTING
STEP 1
Louvres are jammed/not rotating.
STEP 2
Pull the control chain.
STEP 3
Do runners rotate normally?
If yes, return the runners to the
open position and add the louvres.
Pegs should be turned
perpendicular to the headrail.
STEP 4
Add the louvres.
STEP 5
If not, check if any of the pegs within
the headrail have been pushed in,
if they have, using a pair of pliers,
gently pull the pegs back out.
STEP 6
Do the pegs now rotate normally? If
yes, repeat point 3.

PLEASE READ THE INSTRUCTIONS BEFORE OPERATING THIS PRODUCT
If any of the slats are out of alignment, twist the
wand control until the slats are in the closed
position, then continue to twist the wand until all
the slats are fully aligned.
You may feel some resistance and hear a clicking
noise whilst doing so.
MAINTENANCE
The product is low maintenance, however we
recommend that regular visual checks are
completed to ensure that no components have
been damaged, which could result in operating
difficulties and/or cause a safety risk.
To ensure the slats slide smoothly across the
headrail apply some silicone base lubricant spray
to inside of the headrail. If any maintenance is
required we recommend that the work is carried
out immediately by a reputable blind company.
WARNING
Young children can be strangled by loops in pull cords, chains, tapes
and inner cords that operate the product.
To avoid strangulation and entanglement, keep cords out of the reach
of young children.
Cords may become wrapped around a child’s neck.
Move beds, cots and furniture away from window covering cords. Do
not tie cords together. Make sure cords do not twist and create a loop.
Use the wand to draw the slats to either end of the blind. Twist the wand to tilt the slats in either direction to the
open/closed position.
WAND OPERATION-DRAW WAND OPERATION-TILT