SWIT S-2041 User manual

Congratulations on your purchase of this product. Please read this user manual carefully.
Features
 New generation chip-array LED technology, outputs bright but soft & non-glaring light;
 60° wide bea angle, equally spread light, no visible lighting edge and single shadow;
 23W power consu ption, 1200 lux @ 1 eter, equivalent to a 100W halogen bulb, and 10%-100% di erable;
 5000K color te perature and can be switched to 5600K or 3200K by filters;
 6V-17V wide voltage input, support D-tap power, standard DV battery power and special sli battery power;
 High intensity and toughness glass fiber housing, cool-touch, and both screw and cold shoe install.
Product view
Fig 1 Fig 2
Caution
1. Never atte pt to open the device. Refer all servicing to
qualified personnel.
2. Never insert anything into the cooling vent to avoid da age
or short circuit.
3. Keep the light away fro rain or oisture.
4. Please do not stare at the turned on LED light.
5. Keep the filters clean.
6. When powering through DC-IN socket by D-tap cable,
please ake sure the power supply's voltage and power eet
the light input require ents.
7. Working te perature: -10 ~40 ℃ ℃
8. Keep the cooling vent clear to avoid da age.
Clean
Use a soft, dry cloth to clean the LED light. If you clean the
light with soft cloth slightly oistened with neutral detergent,
please dry the surface of the light with a soft, dry cloth. Do
not use a da p cloth or alcohol, gasoline and other solvents
of any kind.
Specifications
Model S-204
Input DC 6V-17V
Power consu ption
Approx. 23W
Bea angle Approx. 60°
Illu inance 1200 lux @ 1 eter
Color te perature 5000K itself,
CRI >85
Working te p. -10 ℃ ~+40 ℃
Storage te p. -20 ℃ ~+55 ℃
Di ension 103×157×84
Mass Approx. 400g
Package
LED light × 1
Cold shoe base × 1
D-tap power cable (S-7104) × 1
Portable bag × 1
User anual × 1
Chip-Array LED Camera Light S-204
USER MANUAL
SWIT Electronics Co., Ltd.
Tel:[phone]
Fax:[phone]
http://www.swit.cc
E- ail: [email protected]
1. 5600K filter
2. Barn door
3. 3200K filter
4. Barn door
5. Cooling vent
6. Switch on/off
7. Knob
8. 1/4” screw bolt
9. Di er
10. DV plate slot
11. DC-IN socket
12. Protection cover
Ver:V1.0.0V00

Usage
. Power the light
S-2041 is 6-17V voltage input and offers various power supply ethods.
● By special slim battery S-8040 (Optional purchase)
① Make sure there’s no power lead connected into DC-IN socket and the light is
switched off (turn the switch to “ 〇 ”).
② Press and slip off the protection cover. See Fig 3
③ Align a fully charged S-8040 battery to the DV ount slot to sa e side, and
press tightly in. Slide the battery downward to snap together. See Fig 4
● By various standard DV camera batteries
① Press and slip off the protection cover. See Fig 3
② Align the S-7004 series battery plate to the DV ount slot to sa e side, and
press tightly in. Then slide the S-7004 downward to snap together. See Fig 5- ①
③ Fix the DV ount with two screws.
④ Make sure the light is switched off (turn the switch to “ 〇 ”). Mount a fully
charged battery to the S-7004 ount. Fig 5- ②
Re ark: After use, please fix on the protection cover.
There’re the following types of S-7004 for choice: (Optional Purchase)
Model Compatible battery type Recommended SWIT battery
S
-
7004F
SONY NP
-
F770/970
S
-
8972, S
-
8970, S
-
8770
S
-
7004P
Panasonic
CGA
-
D54S/D28S
S
-
8D62, S
-
8D54, S
-
8D28
S
-
7004J
JVC BN
-
V428U
S
-
8428
S
-
7004C
Canon BP
-
930/945
S
-
8945, S
-
8845
S
-
7004U
SONY
BP
-
U60/30
S
-
8U62
S
-
7004E
Canon DSLR LP
-
E6
S
-
8PE6
S
-
7004B
Panasonic VW
-
VBG6
S
-
8BG6
S
-
7004V
JVC BN
-
VF823
S
-
8823
S
-
7004
I
JVC SSL
-
JVC50
S
-
8
I50
● By DC input cable
① Make sure the light is switched off (turn the switch to “ 〇 ”). Plug the pole end of
S-7104 into the DC-IN socket.
② Plug the D-tap end of S-7104 to the ca era auxiliary power tap or the battery’s
D-tap output socket. See Fig 6.
③ For third-party DC cables, please ake sure the DC connector is 5.5/2.1
pole and input voltage should be 6-17V; and inner: positive, Outer: negative.
2. Fix the LED light to the camera
● By screw mount (Fig. 8)
The S-2041 can be directly installed on 1/4” thread handle.
● By Cold shoe (Fig. 9- )
① Unscrew the 4 screws and take down the 1/4” bolt base fro the light.
② Install the supplied cold shoe base onto the light.
③ Anticlockwise revolve the fasten knob, and loose the cold shoe slice, then
install onto the ca era cold shoe slot, and fasten the knob to finish.
3. Adjust the angle of the light:
Hold the light, and adjust the light upward or downward. See Fig 12.
4. Open barn doors and filters:
Open the barn doors and filters to about 45°.
5. Switch on:
Turn the switch to “ I ”.
6. Adjust the illuminance:
Adjust the illu inance fro 10% to 100% by the di er.
7. Adjust color temperature:
Output 5600K light by using 5600K filter; Output 3200K light by using 3200K filter
Fig 4
Release button
Screw hole
Battery
release
Fig 6
Pole plug
Fig 7
Fig 12
Adjust upward
or downward
Fig 5
Fig 8
Press and slip
to release
Fig 3
Cover
Fig 9
Fig 10 Fig 11