Symbol LS-3203ER Installation and operation manual

3-1
Chapter 3 Parameter Menus
Set Default Parameter page 3-3
Host Interface Select page 3-4
RS-232C Parameters
Fixed Format Options page 3-5
Code Types page 3-6
Code 2 of 5 Lengths page 3-9
Decode Options page 3-11
UPC-A Preamble page 3-17
UPC-E Preamble page 3-18
Intercharacter Delay page 3-19
Data Transmission Formats page 3-21
Prefix/Suffix Values page 3-22
Transmit Code ID Character page 3-24
Transmit AIM ID Character page 3-25
Laser On Time-out page 3-26
Baud Rate page 3-28
Parity page 3-29
Beep on BEL page 3-30
Hardware Handshaking page 3-31
Software Handshaking page 3-32
Stop Bit Select page 3-33
ASCII Format page 3-34
Power Mode page 3-35

3-2
LS 3203ER Product Reference Guide: Parameter Menus
Wand Host Parameters
Wand Host Interface page 3-36
Code Types page 3-37
Code 2 of 5 Lengths page 3-40
Decode Options page 3-42
Laser On Time-out page 3-44
Power Mode page 3-46
Wand Emulator Bar Output page 3-47
Variable Leading Margin page 3-48
Convert All To Code 39 page 3-50
Synapse Parameters
Code Types page 3-51
Code 2 of 5 Lengths page 3-54
Decode Options page 3-56
UPC-A Preamble page 3-62
UPC-E Preamble page 3-63
Data Transmission Formats page 3-64
Prefix/Suffix Values page 3-65
Transmit Code ID Character page 3-67
Transmit AIM ID Character page 3-68
Laser On Time-out page 3-69
Power Mode page 3-71
For an explanation of these parameters, see page 2-4.

3-3
LS 3203ER Product Reference Guide: Parameter Menus
Set Default Parameters
Refer to the Default Table on page 2-28.
To set defaults for any or all host types, scan the appropriate bar code below.
Then select a specific host interface on the next page.
SET RS-232C DEFAULTS
SETWAND DEFAULTS
SET SYNAPSE DEFAULTS
SET ALL DEFAULTS

3-4
LS 3203ER Product Reference Guide: Parameter Menus
Host Interface Select
To select a host interface, scan the appropriate bar code below.
SET RS-232C HOST
SETWAND HOST
SET SYNAPSE HOST

3-5
LS 3203ER Product Reference Guide: Parameter Menus
RS-232 Host
Fixed Format Options
Select fixed format options for the terminals listed below.
SET NIXDORF
RS-232C FORMATS
SET FUJITSU
RS-232C FORMATS
SET ICL
RS-232C FORMATS

3-6
LS 3203ER Product Reference Guide: Parameter Menus
RS-232 Host
CodeType
Add or delete specific code types by scanning the appropriate bar code(s).
DELETE CODE 39
ADD CODE 39
DELETE UPC-A
ADD UPC-A
DELETE UPC-E
ADD UPC-E
DELETE CODABAR
ADD CODABAR

3-7
LS 3203ER Product Reference Guide: Parameter Menus
RS-232 Host
CodeType
DELETE EAN-8ADD EAN-8
DELETE EAN-13
ADD EAN-13
DELETE I 2 OF 5
ADD I 2 OF 5
DELETE D 2 OF 5ADD D 2 OF 5

3-8
LS 3203ER Product Reference Guide: Parameter Menus
RS-232 Host
CodeType
DELETE CODE 93
ADD CODE 93
DELETE CODE 128
ADD CODE 128
DELETE MSI/Plessey
ADD MSI/Plessey
DELETE EAN 128ADD EAN 128

3-9
LS 3203ER Product Reference Guide: Parameter Menus
RS-232 Host
Code 2 of 5 Lengths
To set the lengths for each code type:
1. Scan the desired option.
2. Scan two bar codes on page 3-10 for each desired length. For example, for
a length of “12”, scan “1” then “2”. For a length of “3”, scan “0”, then “3”.
You must always scan two bar codes for each length .
3. If you make an error, or wish to change your selection, scan CANCEL .
D 2 of 5 LENGTH 1
(RANGE 02-31) D 2 of 5 LENGTH 2
(RANGE 00-31)
I 2 of 5 LENGTH 1
(RANGE 02-32) I 2 of 5 LENGTH 2
(RANGE 00-32)

3-10
LS 3203ER Product Reference Guide: Parameter Menus
RS-232 Host
Code 2 of 5 Lengths
1
23
45
67
89
0
CANCEL