Symmons Naru Series Manual

Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■[phone] ■ Fax: [phone]
©2014 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3050 REV 0 09/02/14
4100-TRM, 4101-TRM
Naru™Trim Series
Operation & Maintenance Manual
Model Numbers Specifications
4100-TRM Valve Trim
4101-TRM Shower Trim
Shower trim includes shower escutcheon kit and 3 mode
showerhead with standard 2.5 gpm (9.5 L/min) ow
restrictor. Valve trim includes shower escutcheon kit only.
Components made from metal and nonmetallic materials
plated in standard polished chrome nish.
Modifications Compliance
-1.5 1.5 gpm (5.7 L/min) flow restrictor
-2.0 2.0 gpm (7.6 L/min) flow restrictor
-412HSB 30" slide bar in place of wall cradle on
hand shower units
-PNL Polished nickel finish
-STN Satin nickel finish
-ASME A112.18.1; CSA B125.1
Warranty
Limited Lifetime - to the original end purchaser in
consumer installations.
5 Years - for commercial installations.
Refer to www.symmons.com/warranty for complete
warranty information.
Note: Append appropriate -sufx to model number.
c

2
Dimensions
Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■[phone] ■ Fax: [phone]
©2014 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3050 REV 0 09/02/14
Measurements
A Ø 2 1/4", 57 mm
B 4 7/8", 124 mm
C 8 1/4", 210 mm
D Ø 7 1/2", 191 mm
E 77", 1956 mm
F 3 1/2", 89 mm
G 42", 1067 mm
H 2 1/4", 57 mm
I 3", 76 mm
J(Rough in)
2 3/8" ± 1/2", 60 mm ± 13 mm
Notes:
1) All dimensions measured from nominal rough-in (see J as reference).
2) Dimensions are subject to change without notice.
FF
A
B
B
D
D
G
G
E
E
C
C
H
H
I
I
J
J
Floor
Floor

3
Parts Breakdown
Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■[phone] ■ Fax: [phone]
©2014 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3050 REV 0 09/02/14
Replacement Parts
Item Description Part Number
A Showerhead 412SH
B
C
Flange
Shower Arm 300
D
I
Handle
Set Screw T-567
E Dome Cover T-544
F
G
H
Shower Escutcheon
Mounting Screws
Mounting Plate
T-273-NS-K002
Note:
1) Append -PNL to part number for polished nickel
nish; -STN for satin nickel.
2) Append -1.5 or -2.0 to showerhead for low ow.
Required for Installation
Adjustable wrench
Phillips head screwdriver
Allen wrench (3/16")
Plumber tape
B
G
C
EF
H
D
A
I

4
Installation
Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■[phone] ■ Fax: [phone]
©2014 Symmons Industries, Inc. ■ www.symmons.com ■ [email protected] ■ ZV-3050 REV 0 09/02/14
Note:
For valve body installation, please
see valve body installation guide.
1) Install large plastic mounting
plate (H) to shower valve
(4000-BODY). Secure with two
screws (G).
2) Attach shower escutcheon (F) to
large plastic mounting plate (H).
Note: Tabs should snap into place.
3) Install dome cover (E) to valve by
turning clockwise.
4) Install shower handle (D) to
valve. Secure handle by
tightening set screw (I).
Note: Handle should be facing the
12 o'clock position.
5) Attach shower arm (C) and ange
(B) to vertical shower pipe turning
clockwise to tighten.
6) Install showerhead (A) to shower
arm (C) turning clockwise to
tighten.
1
2
G
H
FH
1
2
E
1
2
A
C
1
2
C
B
1
I
2
D