Syscall Nttworks GP-206RT User manual

User Manual
Please read the user manual carefully
before start using the device.
User Manual
GP-206RT
1
34
56
2

Table of contents
1. Components & Specification · · · · · · · · · · · · · · · · · · · · · · · · · · · · 3
2. Getting Started · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 3
3. Settings · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 4
3-1. Channel Number Setting · · · · · · · · · · · · · · · · · · · · · · · · · · · · 5
3-2. Group Number Setting · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 5
3-3. Pager Ring Time Setting · · · · · · · · · · · · · · · · · · · · · · · · · · · · 6
3-4. Pager Number Setting · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 7
3-5. Other Settings · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 7
3-5-1. Pager Alarm Type Setting · · · · · · · · · · · · · · · · · · · · · · · 7
3-5-2. Anti-Theft & Out-Range Setting · · · · · · · · · · · · · · · · · · · · 8
3-6. Exit from Settings · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 8
3-7. RF Test Mode · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 9
3-8. Call Button ON/OFF · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 10
3-9. Pager Vibration Intensity · · · · · · · · · · · · · · · · · · · · · · · · · · · · 10
3-10. Call Button Selection · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 11
3-11. Transmission Output Setting · · · · · · · · · · · · · · · · · · · · · · · · ·11
3-12. Initialization · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 12
4. How to Use GP-206RT · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 12
4-1. Call a pager · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 12
4-2. Attend to a call · · · · · · · · · · · · · · · · · · · · · · · · · · 12
- 2 -

0
00
00
0
Components
1. Components & Specification
Pager
(6pcs) Transmitter-charging dock Antenna Power adapter (DC 8V/3A)
User Manual
Pager (GP-200R)
Specification
Frequency
Power source
Battery
Dimension
Weight
Color
FSK/433MHz
DC 3.7V/180mA
Lithium-polymer battery
W53 x L105 x H11(mm)
35g
Black
Transmitter-charging dock (GP-206T)
Frequency
Power source
Antenna type
Dimension
Weight
Color
FSK/433MHz
DC 8V/3A
SMA type
W140 x L149 x H40(mm)
120g
Black
2. Getting Started
· Plug the power at the rear of the transmitter-charging dock, and connect the antenna.
Rear of the
transmitter-
charging
dock
Antenna connector
Power connector
Call
button
· Insert all pagers into the transmitter-charging dock
in order to start charging.
· The Red LED on the pager turns on while it is
charging, and switches to Blue LED when it is
fully charged.
Power
Adapter
Pager
- 3 -

Setting menus & code [Quick Guide]
Channel Number
Group Number
Pager Ring Time
Pager number
Other settings
Exit from settings
RF Test Mode
Call Button ON/OFF
Pager Vibration
Intensity
Call Button
Selection
Transmission
Output Setting
Initialization
1
+ 1
+ 1
+ 5
1
Vibration
-
-
on/off
1(Weak)
1~6
Min
-
2
+ 2
+ 2
+ 10
2
Sound
-
-
on/off
2
7~12
2
-
3
+ 4
+ 4
+ 20
3
LED(on)
-
-
on/off
3(Mid)
-
3
-
4
+ 8
+ 8
+ 40
4
Anti-Theft
-
-
on/off
4
-
Normal
-
5
+ 16
+ 16
-
5
Out-Range
-
-
on/off
5(Strong)
-
Max
-
6
Save & exit
Save & exit
Save & exit
6 / Save & exit
Save & exit
-
-
on/off
Save & exit
Save & exit
Save & exit
Save & exit
-
Setting Menu
Code Number key
* Warning: All pagers should be placed on the transmitter-charging dock while setting.
Press and hold 5 for about 10 seconds and the
device becomes input standby mode
(Press and hold until it makes “Beep~~” noise)
* If you do not touch any key buttons for more than 25 seconds, it is automatically exited from the settings.
3. Settings
3-1. Channel Number Setting [Setting code: 664231]
User can prevent the signal interference with the neighboring Syscall systems
by setting their own channel number.
1. Press and hold 5 for about 10 seconds and
the device becomes input standby mode
(Press and hold until it makes “Beep~~” noise)
- 4 -
12 3 4 5 6
1~6
⑥⑥④②③①
⑥⑥④②③②
⑥⑥④②③③
⑥⑥④②③④
⑥⑥④②③⑤
⑥⑥④②③⑥
⑥⑥④②④①
⑥⑥④②④②
⑥⑥④②④③
⑥⑥④②④⑥
⑥⑥④②⑤①
⑤②④④①⑥
7~12
⑫⑫⑩⑧⑨⑦
⑫⑫⑩⑧⑨⑧
⑫⑫⑩⑧⑨⑨
⑫⑫⑩⑧⑨⑩
⑫⑫⑩⑧⑨⑪
⑫⑫⑩⑧⑨⑫
⑫⑫⑩⑧⑩⑦
⑫⑫⑩⑧⑩⑧
⑫⑫⑩⑧⑩⑨
⑫⑫⑩⑧⑩⑫
⑫⑫⑩⑧⑪⑦
⑪⑧⑩⑩⑦⑫
12 3 4 5 6

[Example – Pn/Gn number setting]
Button
Pn/Gn
number
1
+1
2
+2
3
+4
4
+8
5
+16
1
2
3
4
5
...
31
3. Pick one group number from 1 to 31,
and then press 6 to save and return to
previous menu.
3-2. Group Number Setting [Setting code: 664232]
User can prevent the signal interference with the neighboring Syscall systems
by setting their own group number.
1 2 3 4 5 6Button
Setting value +8+1 +2 +4 +16 Save&exit
2. Press 6-6-4-2-3-2 to enter the group number
setting mode.
ex. Set group number 16 → press 5
1. Press and hold 5 for about 10 seconds and
the device becomes input standby mode
(Press and hold until it makes “Beep~~” noise)
- 5 -
2. Press 6-6-4-2-3-1 to enter the channel
number setting mode.
3. Pick one channel number from 1 to 31,
and then press 6 to save and return to
previous menu.
ex. Set channel number 3 → press 1 and 2
1 2 3 4 5 6Button
Setting value +8+1 +2 +4 +16 Save&exit
12 3 4 5 6
12 3
4
6 6
22 3
4
6 6
12 3
4 5 6
12 3
4 5 6

3-3. Pager Ring Time Setting [Setting code: 664233]
User can set the pager ring time.
2. Press 6-6-4-2-3-3 to enter the pager ring time
setting mode.
3. Set the ring time, and then press 6 to save and
return to previous menu. (Default: 30 seconds)
[Example – Ring time setting]
Button
Call time
30 sec
35sec
40 sec
...
60 sec
75 sec
1
+5
2
+10
3
+20
4
+40
5
-
1. Press and hold 5 for about 10 seconds and
the device becomes input standby mode
(Press and hold until it makes “Beep~~” noise)
Pager registration
3-4. Pager Number Setting [Setting code: 664234]
2. Press 6-6-4-2-3-4 to enter the pager number
setting mode.
1. Press and hold 5 for about 10 seconds and
the device becomes input standby mode
(Press and hold until it makes “Beep~~” noise)
1 2 3 4 5 6Button
Setting value +40+5 +10 +20 -Save&exit
- 6 -
12 3 4 5 6
32 3
4
6 6
12 3 4 5 6
42 3
4
6 6
12 3
4 5 6

When the distance between transmitter and pager goes beyond the wireless range,
either the transmitter or pager starts alert after 10 or 16 minutes respectively.
3-5-2. Anti-Theft & Out-Range Setting [Setting code: 664235]
2. Press 6-6-4-2-3-5 to enter the other setting
mode.
1. Press and hold 5 for about 10 seconds and
the device becomes input standby mode
(Press and hold until it makes “Beep~~” noise)
3-5. Other Settings
3-5-1. Pager Alarm Type Setting [Setting code: 664235]
2. Press 6-6-4-2-3-5 to enter the other setting
mode.
3. User can press 1 for vibration and 2 for sound.
LED cannot be turned off.
(Default: Vibration+Sound+LED)
1 2 3 4 5 6
Vibration
Button
Setting value
Sound LED - - Save&exit
4. Press 6 to save and return to previous menu.
1. Press and hold 5 for about 10 seconds and
the device becomes input standby mode
(Press and hold until it makes “Beep~~” noise)
3. Press the number to be registered to the pager.
Check if the LED flashes.
And then, take the relevant pager off from
the dock
4. Press and hold 6 to save and return to
previous menu.
- 7 -
12 3 4 5 6
52 3
4
6 6
12 3 4 5 6
52 3
4
6 6
0
00
00
0
1
2
3
5
12 3 4 5 6
12 3 4 5 6

3-6. Exit from Settings [Setting code: 664236]
Press 6-6-4-2-3-6 to exit.
* If you do not touch any key buttons for more than 25 seconds, it is automatically exited from
the settings.
4. Press 6 to save and return to previous menu.
3. Press the applicable button to set
Anti-theft and/or Out-range.
1 2 3 4 5Button
Setting value Anti-theft--- Out-range
6
Save&exit
* Anti-theft function: Alert on transmitter.
(LED blink & Sound)
* Out-Range function: Alert on Pager. (Sound)
3-7. RF Test Mode [Setting code: 664241]
User can verify the channel number (Pn), group number (Gn) and the call number
of the pager when the RF test mode is on.
2. Press 6-6-4-2-4-1 to enter the RF test mode.
3. When the RF test mode turns on, the relevant number displays in the order of
call number of the pager, frequency, FND test, version info, Gn and Pn.
1. Press and hold 5 for about 10 seconds and
the device becomes input standby mode
(Press and hold until it makes “Beep~~” noise)
Pager No. Frequency FND Test Version info Gn Pn
- 8 -
12 3 4 5 6
62 3
4
6 6
12 4
4
6 6
12 3 4 5 6
12 3 4 5 6

User can inactive call buttons on the transmitter-charging dock when there are
lost or not in use pagers.
3-8. Call Button ON/OFF [Setting code: 664242]
2. Press 6-6-4-2-4-2 to enter the call button
on/off setting mode.
3. Press the call button that is to be turned off.
It turns back on when you press it again.
LED light on the call button will turn on/off
accordingly.
4. Press and hold 6 to save and return to
previous menu.
1. Press and hold 5 for about 10 seconds and
the device becomes input standby mode
(Press and hold until it makes “Beep~~” noise)
## The call button on/off status is indicated with LED for about 1 second as soon as the power is supplied.
3-9. Pager Vibration Intensity [Setting code: 664243]
User can set the vibration intensity level from 1 to 5.
2. Press 6-6-4-2-4-3 to enter the vibration
intensity setting mode.
3. Press the applicable call button to set the vibration intensity.
4. Press 6 to save and return to previous menu.
1. Press and hold 5 for about 10 seconds and
the device becomes input standby mode
(Press and hold until it makes “Beep~~” noise)
6
Save & exit
1 2 3 4 5Button
Setting value 41(Weak) 23(Mid)
5(Strong)
- 9 -
12 3 4 5 6
22 4
4
6 6
12 3 4 5 6
12 3 4 5 6
12 3 4 5 6
32 4
4
6 6
12 3 4 5 6

4. Press 6 to save and return to previous menu.
3-10. Call Button Selection [Setting code: 664246]
User can set whether to use the pagers as 1~6 or 7~12.
This feature is required when 2 sets of GP-206RT are used in the same place.
2. Press 6-6-4-2-4-6 to enter the transmission
button selection setting mode.
3. Press 1 to use them as 1~6 or 2 to use them as 7~12.
1. Press and hold 5 for about 10 seconds and
the device becomes input standby mode
(Press and hold until it makes “Beep~~” noise)
6
Save & exit
1 2 3 4 5Button
Setting value -1~6 7~12 - -
4. Press 6 to save and return to previous menu.
User can set the transmission output level from 1 to 5.
3-11. Transmission Output Setting [Setting code: 664251]
2. Press 6-6-4-2-5-1 to enter the transmission
output setting mode.
3. Press the applicable call button to set the output level.
1. Press and hold 5 for about 10 seconds and
the device becomes input standby mode
(Press and hold until it makes “Beep~~” noise)
6
Save & exit
1 2 3 4 5Button
Setting value NormalMin 2 3 Max
- 10 -
12 3 4 5 6
62 4
4
6 6
12 3 4 5 6
12 3 4 5 6
12 5
4
6 6
12 3 4 5 6

3-12. Initialization [Setting code: 524416]
User can initialize the registered pagers and the transmitter.
But this is only applicable when the Gn, Pn of the pagers and the transmitter are
matched up together.
2. Insert all pagers into the transmitter-charging dock.
3. Press 5-2-4-4-1-6 and start initializing.
1. Press and hold 5 for about 10 seconds and
the device becomes input standby mode
(Press and hold until it makes “Beep~~” noise)
- 11 -
4. How to Use GP-206RT
4-1. Call a pager
4-2. Attend to a call
Take one of the pager off from
the transmitter-charging dock.
Return the pager to where the pager
is given when the pager starts buzzing.
Place the pager back to the
transmitter-charging dock to recharge.
Press the pager number from
the transmitter-charging dock
to call the pager.
64 1
4
5 2
12 3 4 5 6
2
2
1
34
56
2
13
1
34
56

1
34
56
2
SYSCALL France - www.syscallglobal.fr
0033 (0)1 84 17 61 81 - [email protected]
242 boulevard de Stalingrad 94500 Champigny sur Marne,
France
Manufacturer
■NTTWORKS CO., LTD
413-9 NTTWORKS Bldg, Galhyun-Dong, Eunpyong-Gu
Seoul, Korea