System air AxZent 400 Manual

Installation, Operation and Maintenance instruction
AxZent Thermo Centrifugal fan AC
AxZent Thermo Centrifugal fan EC

Table of content
1 Introduction .......................................................... 1
1.1 Product description ......................................1
1.2 Intended use ..............................................1
1.3 Document description...................................1
1.4 Product overview.........................................1
1.5 Name plate ................................................2
1.5.1 Type designation ............................. 2
1.6 Product liability............................................ 2
2 Safety .................................................................3
2.1 Safety definitions.........................................3
2.2 Safety instructions ....................................... 3
2.3 Personal protective equipment ....................... 3
3 Transportation and storage ...................................... 4
4 Installation............................................................ 4
4.1 To do before the installation of the
product......................................................4
4.2 To install the product ....................................5
5 Electrical connection...............................................6
5.1 To do before the electrical connection .............. 6
5.2 To connect the product to the power
supply.......................................................6
5.3 Speed controller for EC motors....................... 6
5.4 Motor protection for EC motors ....................... 6
5.5 Speed controller for AC motors....................... 6
5.6 To install motor protection for AC
motors ......................................................7
6 Commissioning ..................................................... 7
6.1 To do before the commissioning......................7
6.2 To do the commissioning...............................7
7 Operation.............................................................8
7.1 To start a product with an EC motor ................. 8
7.2 To start a product with an AC motor ................. 8
7.3 To stop the product ......................................8
7.3.1 To stop the product in an
emergency..................................... 8
8 Maintenance......................................................... 9
8.1 Maintenance schedule.................................. 9
8.2 To clean the product..................................... 9
8.3 Spare parts ................................................ 9
9 Troubleshooting................................................... 10
10 Disposal........................................................... 12
10.1 To disassemble and discard the parts of the
product.................................................... 12
11 Warranty .......................................................... 12
12 Technical data ................................................... 13
12.1 Technical data overview .............................. 13
12.2 Product dimensions ................................... 13
12.3 Wiring diagrams ........................................ 14
12.3.1 Wiring diagrams for speed
controllers for EC motors................. 14
12.3.2 Wiring diagrams for ON/OFF
controls for EC motors .................... 16
13 Accessory overview............................................ 17
14 EU Declaration of Conformity................................ 18
15 UKCA Declaration of Conformity............................ 19

1 Introduction
1.1 Product description
This product is a thermo centrifugal fan with a radial fan im-
peller. The motor is located outside the airstream. The casing
has flanges that agree with Eurovent 1/2.
The product is not supplied with a safety switch, external
speed control or vibration dampers. These are available as
accessories.
1.2 Intended use
The product is used for transportation of clean or contami-
nated air with a maximum temperature of 120°C.
The product is intended for installation in duct systems. The
product can also be installed with free suction or free dis-
charge together with a protection grille.
The product is not applicable for transportation of air that
contains explosive, flammable or aggressive media. The
product is not applicable for locations where there is a risk of
explosion.
1.3 Document description
This document contains instructions for installation, operation
and maintenance of the product. The procedures must be
done by approved personnel only.
Speak to Systemair for more information on how to install the
product in different installation locations.
1.4 Product overview
1 2 3 4
5
6
1. Name plate
2. Connection box
3. Motor name plate
4. Motor
5. Casing
6. Fan impeller
1

1.5 Name plate
1
7
9
8
10 12 13
2 3 4 5 6
14
11
1. Type designation: Product name, dimension and motor
type. Refer to 1.5.1 Type designation page 2.
2. Current, A
3. Input power, W
4. Frequency, Hz
5. Certifications
6. Scannable code 1
7. Voltage, V
8. Maximum temperature of transported air, °C
9. IP code, enclosure class
10. Insulation class
11. Serial number: part number/production number/produc-
tion date
12. Nominal fan speed
13. Weight, kg
14. Country of production
Note:
The data on the name plate applies to “standard air” that is
specified in the standard ISO5801.
1.5.1 Type designation
Product name AxZent
Dimension 400
450
500
560
630
Motor type EC: Electronically commutated, 1–
phase
EC-L: Electronically commutated,
3–phase
E4: 4 pole, AC motor, 1–phase
DV: 4 pole, AC motor, 3–phase
D2: 2 pole, AC motor, 3–phase
D4: 4 pole, AC motor, 3–phase
1.6 Product liability
Systemair is not liable for damages that the product causes
in these conditions:
• The product is incorrectly installed, operated or
maintained.
• The product is repaired with parts that are not original
spare parts from Systemair.
• The product is used together with accessories that are not
original accessories from Systemair.
• The product is used without motor protection.
2
1. Use a mobile device to scan the scannable code and go to the Systemair documentation portal for more documentation and document
translations.

2 Safety
2.1 Safety definitions
Warnings, cautions and notes are used to point out specially
important parts of the manual.
Warning
If you do not obey these instructions,
there is a risk of death or injury.
Caution
If you do not obey these instructions,
there is a risk of damage to the product,
other materials or the adjacent area.
Note:
Information that is necessary in a given situation.
2.2 Safety instructions
Warning
Read the warning instructions that follow
before you do work on the product.
• Read this manual and make sure that you understand the
instructions before you do work on the product.
• Obey local conditions and laws.
• The ventilation contractor and the operator are responsi-
ble for correct installation and intended use.
• Keep this manual at the location of the product.
• Do not install or operate the product if it is defective.
• Do not remove or disconnect safety devices.
• Make sure that you can read all warning signs and labels
on the product when it is installed. Replace labels that
have damage.
• Only permit approved personnel to work on the product
and to be in the adjacent area during all work on the
product.
• Make sure that you know how to stop the product quickly
in an emergency.
• Use applicable safety devices and personal protective
equipment during all work on the product.
• Before you do work on the product, stop the product and
wait until the fan impeller stops. Make sure that there is no
voltage on the motor terminals.
• If the maintenance is not correctly and regularly done,
there is risk of injury and damage to the product.
• Only do the maintenance as given in this manual. Speak
to Systemair technical support if other servicing is
necessary.
• Always use spare parts from Systemair.
• Sound levels exceeding 70 dB(A) may occur depending
on model and size. Visit www.systemair.com for more de-
tailed information about your product.
• The product is not to be used by persons, including chil-
dren, with reduced physical, sensory or mental capabil-
ities, or lack of experience and knowledge, unless they
have been given supervision or instruction.
• Do not allow children to play with the device.
2.3 Personal protective
equipment
Use personal protective equipment during all work on the
product.
• Approved eye protection
• Approved protective helmet
• Approved hearing protection
• Approved protective gloves
• Approved protective shoes
• Approved work clothing
3

3 Transportation and
storage
Warning
Make sure that the product does not
become damaged or wet during
transportation. A damaged or wet
product can cause fire or electric shock.
• Before you move the product to the installation location,
examine the packaging for damages.
• Do not move the product by the cables, terminal box, fan
impeller, protection grille, inlet cone or silencer.
• If lifting equipment is used, make sure that the lifting
equipment can hold the weight of the product. Refer to the
name plate for information. Do not lift the product by the
packaging.
Warning
Do not walk below a lifted product.
• Keep the correct side of the packaging up during
transportation. Refer to the arrows on the packaging.
• Load and unload the product carefully.
• Keep the product in a dry and clean location during
storage. Make sure that the ambient temperature during
storage is between –10 and +30 °C. A stable ambient
temperature prevents damage from condensation.
• Keep the product in storage for maximum 1 year.
4 Installation
4.1 To do before the installation
of the product
• Make sure that you have the necessary installation
accessories:
– Refer to 13 Accessory overview page 17 for an over-
view of the accessories.
– If you install the product outdoors, it is necessary to in-
stall a weather protection roof.
– To decrease vibrations transmitted from the product to
the duct system, Systemair recommends to install vi-
bration dampers, fast clamps or flexible connections.
– If you install the product with free suction or free dis-
charge, it is necessary to install a protection grille.
Make sure that the safety distance agrees with the
standard DIN EN ISO 13857 and the standard DIN
24167–1.
• Use installation material with fire resistance rating for the
installation location.
• Examine the packaging for transportation damage and re-
move the packaging from the product carefully.
• Examine the product and all components for damage.
• Make sure that the motor effect and the fan performance
agrees with the expectations at the installation location.
• Make sure that the information on the name plate and the
motor name plate agrees with the operation conditions.
• Install the product in a location where there is space for
commissioning, troubleshooting and maintenance.
• Make sure that the installation location is clean and dry,
for full safety during electrical work.
• Make sure that the installation surface has sufficient ca-
pacity to hold the weight of the product.
• Refer to the airflow direction arrows on the name plate or
on the product to install the product in the correct position.
• Make sure that all cable glands are tight against the ca-
bles to prevent leaks.
4

4.2 To install the product
1Put the product in the correct position:
a. Install the product with the motor up or to the sides.
45°
135°
135°
45°
Caution
Do not install the product with the motor
down. Dirt can collect in the fan housing.
b. Install the product correctly in relation to the airflow.
2Install the product with accessories that decrease vibra-
tions in the product and the duct system.
a. If you install the product vertically, install mounting
rings (A) against the ceiling and use flexible connec-
tions (B):
B
A
b. If you install the product horizontally, install mount-
ing feet (C) and spring vibration dampers (D).
C
D
5

3If you install the product near a duct bend, do these
steps to prevent vibrations, unwanted noise and de-
creased air pressure:
a. Measure the distance (A) between the product and
the duct bend.
b. Make sure that the distance (A) is a minimum of 2.5
x the diameter (B) of the duct system. For circular
ducts, (B) is the nominal diameter. For rectangular
ducts, (B) is the hydraulic diameter.
AA
B
5 Electrical connection
5.1 To do before the electrical
connection
• Make sure that the electrical connection agrees with the
product specification on the motor name plate.
• Make sure that the environment for electrical connection
is clean and dry.
• Make sure that the wiring diagram that is included with the
supply of the product agrees with the terminals in the con-
nection box.
5.2 To connect the product to the
power supply
• Complete the electrical connection for the motor. Refer to
the motor wiring diagram that is included with the product.
• Make sure that the cross section of the protective earthing
is equal to or larger than the cross section of the phase
conductor.
• Install a circuit breaker in the permanent electrical installa-
tion, with a contact opening of a minimum 3 mm at each
pole.
• If a residual current device (RCD) is installed, make sure
that it is an all-current sensitive RCD. Consider if the prod-
uct has a frequency converter, uninterruptible power sup-
ply (UPS), or an EC motor. EC motors have a leakage
current to earth that is <=3.5 mA.
5.3 Speed controller for EC
motors
• EC motors are controlled through a stepless 0–10 V signal.
• Do not use power supply for the speed controller.
• Refer to 12.3 Wiring diagrams page 14 and the instruction
manual for the external speed controller.
5.4 Motor protection for EC
motors
EC motors have an integrated motor protection. Reset the
motor protection by disconnecting the fan from power supply
for 60 seconds.
5.5 Speed controller for AC
motors
Note:
The speed controller alternatives are different for different
motor types. Make sure that your motor is compatible with
the speed controller type before you use it.
The speed can be controlled by voltage reduction using a
transformer. It is also possible to control the fan speed with
frequency converter if the installed frequency converter has
built in all-pole sine filter and shielded cables are not needed.
6

5.6 To install motor protection for
AC motors
• If the product has an built in motor protection, reset by dis-
connecting the product from power for 60 seconds.
• If the motor has temperature monitors such as thermal
contacts (TK) or thermistors lead out into the terminal box,
these must always be connected in the control circuit us-
ing appropriate motor protection.
• Make sure that an overheated motor cannot start again
automatically when it becomes cool.
• Install the motor cables and the temperature monitor apart.
• If the motor does not have temperature monitors, install a
motor protection switch.
6 Commissioning
Caution
• If strong vibrations occur during
commissioning, immediately increase
or decrease the fan speed until the
vibrations are decreased. Continuous
strong vibrations can cause damage
to components.
• Do not increase the fan speed to a
higher rpm value than the maximum
value that is given on the name plate.
The commissioning report is found at www.systemair.com.
6.1 To do before the
commissioning
• Make sure that the installation and electrical connection
are correctly done.
• Visually examine the product and accessories for damage.
• Make sure that the safety devices are correctly installed.
• Make sure that there are no blockages in the air inlet and
the air outlet.
• Make sure that installation material and unwanted objects
are removed from the product and the ducts.
6.2 To do the commissioning
1Set the installed safety switch in the OFF position.
2If it is possible to get access to the fan impeller, do the
steps that follows:
a. If it is necessary, remove parts of the installation.
b. Turn the fan impeller by hand and make sure that it
turn easily.
c. Record the result in the commissioning report.
3Make sure to turn the product in a direction that agrees
with the related arrow on the product.
a. Record the result in the commissioning report.
4If you removed parts of the installation to get access to
the fan impeller, install the removed parts again.
5Set the installed safety switch in the ON position.
6Start the product.
7Set the minimum operation speed.
8Increase the operation speed gradually to the maximum
operation speed.
a. Examine the vibrations in the casing and the bearing
areas at all speed levels.
b. Make sure that the vibrations agree with the specifi-
cations in DIN ISO 14694.
c. Make sure that none of the speed levels cause un-
wanted noise in the product.
d. Record the result in the commissioning report.
9Record the necessary data in the commissioning report.
7

7 Operation
Caution
EC motors must be set to ON/OFF via
the control input. To stop the product via
mains supply decreases the life time of
the motor. Systemair recommends to
install external speed controller for easy
access to control the input signal.
7.1 To start a product with an EC
motor
1Make sure that the 0–10 V signal is set to “0” with the
speed controller.
2Set the installed safety switch in the ON position and wait
5 seconds.
3Adjust the fan speed with the 0–10 V signal speed con-
troller. If an external speed controller is not installed, ad-
just the fan speed directly with the integrated
potentiometer.
7.2 To start a product with an AC
motor
1Set the installed safety switch in the ON position.
2Install the external speed controller. Refer to the instruc-
tion manual for the installed speed controller.
7.3 To stop the product
1Set the installed speed controller in the OFF position.
Refer to the instruction manual for the installed speed
controller.
2Set the installed safety switch in the OFF position.
7.3.1 To stop the product in an
emergency
• Set the installed safety switch in the OFF position.
8

8 Maintenance
Warning
Set the installed safety switch in the OFF position before you do the maintenance unless the instructions tell
you differently. Make sure that the safety switch is not accidentally set in the ON position.
8.1 Maintenance schedule
The intervals are calculated from continuous operation of the product.
Maintenance task Usual operation
conditions
Unusual operation conditions. 1
Each 6
months
Each
year
Each 3
months
Each 6
months
Each
year
Visually examine the product and its components for damage,
corrosion and dirt.
X X
Examine the fan impeller for damage and imbalance. X X
Clean the product and the ventilation system. X X
Do a check of all fasteners and make sure that they are fully
tightened.
X X
Make sure that the product and its components are correctly
operated.
X X
Measure the power consumption and compare the result with
the information on the name plate.
X X
If vibration dampers are installed, make sure that they operate
correctly and examine them for damage and corrosion.
X X
Make sure that the electrical protective equipment and the me-
chanical protective equipment operates correctly.
X X
Make sure that you can read the name plates of the product. X X
Examine all cable connections for damage. Make sure that
the cable glands are tight against the cables.
X X
If flexible connections are installed, examine them for damage. X X
1. The unusual operation conditions are classified as follows: If a stable ambient temperature is higher than 30 °C or lower than -10° C, if the
temperature changes are large or if very contaminated air is transported.
8.2 To clean the product
Caution
• Do not clean the product with a high-
pressure washer.
• Do not clean the product with steel
brushes or sharp objects.
• Do not bend the fan impeller blades.
• Be careful not to move the balance
weights on the fan impeller.
• Remove dirt from the fan and the duct.
• If access to the fan impeller is possible, clean the fan im-
peller with a moist cloth or soft brush.
8.3 Spare parts
• For information about spare parts, send an e-mail to
[e-mail].
• For more information about spare parts, contact Systemair
support.
• Always use spare parts from Systemair.
• When you send an order for spare parts, include the serial
number of the product. The serial number is found on the
name plate.
9

9 Troubleshooting
Note:
If you cannot find a solution to your problem in this section, speak to Systemair technical support.
Problem Cause Solution
The product does not operate smoothly.
The fan impeller is not correctly
balanced.
Speak to Systemair technical support.
There is dirt on the fan impeller. Clean the fan impeller carefully. Refer
to 8.2 To clean the product page 9.
The fan impeller has damages or
deformations because the transported
air contains aggressive media.
Speak to Systemair technical support.
The fan impeller does not turn in the
correct direction.
Make sure that the electrical connection
is correctly done.
The fan impeller has deformations
because of too high temperatures. • Replace the fan impeller.
• Make sure that the temperature of
the transported air is not higher than
the value on the name plate.
There are unusually strong vibrations in
the product or the duct system.
Make sure that the product is correctly
installed. Do a check of the duct system.
The product is operated in a resonant
frequency range.
Increase or decrease the fan speed
until the product operates smoothly.
Refer to 6 Commissioning page 7.
The air output is not sufficient.
The fan impeller does not turn in the
correct direction.
Make sure that the electrical connection
is correctly done.
The electrical connection is not
correctly done.
Make sure that the electrical connection
agrees with the wiring diagrams.
The air pressure is too low because of
incorrect installation.
Do the necessary changes in the duct
system and installed components to
increase the air pressure. Refer to 6
Commissioning page 7.
The airflow shutters are closed or not
fully open.
Adjust the airflow shutters.
There is blockage in the air inlet or the
duct system.
Remove the blockage.
The product is not applicable for the
installation location.
Make sure that the product is applicable
for the installation location.
The motor power is decreased because
of too high temperature in the motor.
Note:
This is applicable for EC motors only.
• Do a check of the ambient
temperature.
• Make sure that the space around the
motor is sufficient to keep the
temperature down.
There is unusual noise when the
product starts or operates.
There is strain in the connections of the
duct system.
Loosen the connections, align the parts
of the duct system correctly and tighten
the connections.
10

Problem Cause Solution
Thermal contacts, PTC or resistors are
released.
The fan impeller does not turn in the
correct direction.
Make sure that the electrical connection
is correctly done.
A phase loss occurred. If the motor is a 3-phase motor, make
sure that no phase is missing.
Note:
This is not applicable for EC motors.
The motor is overheated. • Do a check of the motor cooling
impeller.
• If it is possible, measure the
resistance to do a check of the motor
winding.
The capacitor is not connected or not
correctly connected.
Note:
This is not applicable for EC motors
or 3–phase AC motors.
Connect the capacitor correctly. Refer
to the included motor wiring diagram.
There is blockage in the motor. Speak to Systemair technical support.
The fan speed does not get the nominal
value.
Defective motor winding. If it is possible, measure the resistance
to do a check of the motor winding.
The speed control is not correctly set. Set the speed control correctly.
The fan impeller cannot turn freely
because of mechanical blockage.
Remove the blockage.
Phase loss occurs. If the motor is a 3-phase motor, make
sure that no phase is missing.
The motor does not rotate.
A component in the power supply is
defective.
Do a check of the power supply.
Replace defective components and
connect the power supply again.
The electrical connection is not
correctly done.
Make sure that the electrical connection
agrees with the wiring diagrams.
The motor protection is released
because the motor is overheated.
Let the motor become cool. Reset the
motor protection. Find the cause of the
overheated motor.
A phase loss occurred. If the motor is a 3-phase motor, make
sure that no phase is missing.
The electronic components or the motor
is overheated.
The motor is overloaded or the ambient
temperature is too high.
Let the motor become cool. Reset the
motor protection. Find the cause of the
overheated motor.
The motor is overloaded. Make sure that the product is applicable
for the installation location.
The ambient temperature is too high. Make sure that the product is applicable
for the installation location.
The cooling of the product is not
sufficient.
Make sure that the space around the
motor is sufficient to keep the
temperature down.
11

10 Disposal
The product follows the WEEE directive. This symbol on the
product or the packaging of the product shows that this
product is not domestic waste. The product must be recycled
at an approved disposal location for electrical and electronic
equipment.
10.1 To disassemble and discard
the parts of the product
1Disconnect and disassemble the product in the opposite
sequence of electrical connection and installation.
2Recycle the product parts and the packaging at an appli-
cable disposal location.
3Obey the local and national requirements for disposal.
11 Warranty
For warranty claims, send a written maintenance plan and
the commissioning report to Systemair. The warranty is only
applicable for these conditions:
• The product is correctly installed and operated.
• Motor protection is used.
• The instructions in the data sheets are obeyed.
• Maintenance instructions are obeyed.
• A product that is not operated continuously is operated for
a minimum of 1 hour each month.
12

12 Technical data
12.1 Technical data overview
Max. temperature of transported air, °C 120
Sound pressure, dB Refer to the data sheet in the online catalogue at www.systemair.com.
IP class
Voltage, current, frequency, enclosure
class, weight Refer to the name plate. Refer to 1.5 Name plate page 2 for more information.
Motor data Refer to the motor name plate or the technical documentation from the motor
manufacturer.
12.2 Product dimensions
AE
B
C
D
F
G
H
AxZent 400 AxZent 450 AxZent 500 AxZent 560 AxZent 630
A, mm 391.7 445.7 495.7 558 629.7
B, mm 400.5 450.5 500.5 560.5 630.5
C, mm 450 500.4 560 620 690
D, mm 8 × 45° 8 × 45° 12 × 30° 12 × 30° 12 × 30°
E, mm 8 × Ø12 8 × Ø12 12 × Ø12 12 × Ø12 12 × Ø12
F, mm 585.7 622.5 720 795 825
G, mm 480 530 590 650 720
13

AxZent 400 AxZent 450 AxZent 500 AxZent 560 AxZent 630
H, mm
Motor type
EC 635 660 746 795 899
E4 653.8 679.2 744.2 815 898
DV 637.5 662.9 727.7 N/A N/A
D2 722.5 748.4 N/A N/A N/A
D4 N/A N/A N/A 808.4 898
12.3 Wiring diagrams
The wires in the motor cables have these colours:
Wire Colour
+10V Red
0...10V/PWM Yellow
GND Blue
12.3.1 Wiring diagrams for speed controllers for EC motors
Note:
An internal potentiometer is installed on the terminal block from the factory. Remove the internal potentiometer when you use
an external speed controller for the EC fan.
MTP 10
MTP 10
1
2
4/+
3/Us
5/-
+10V
0...10V
GND
MTP 20
MTP 20
1/Vdc+
4/Vout
3/Vout-
2/Vdc-
+10V
0...10V
GND
14

EC-Basic
EC-Basic
230V AC
1/IN Vac
2/IN Vac
4/Out
5/GND
+10V
0...10V
GND
MTV–1/10
MTV 1/010
1/IN Vac
2/IN Vac
4/Out+
5/Out-
+10V
0...10V
GND
230V AC
S-5EC/FRQ
MTP 10
GND
10V
A
+10V
0...10V
GND
EC-Vent
EC-Vent
IN/RPM
PWM
IN/10V
OUT/PWN
GND
TACH
optional
+10V
0...10V/PWM
GND
15

12.3.2 Wiring diagrams for ON/OFF controls for EC motors
CO2RT-R(-D)
CO2RT-R-D
24V AC
Supply
Neutral
Common
Relay NO
Relay NC
+10V
0...10V
GND
Din1
IR24–P
IR24-P
24V AC or DC
24V
Neutral
Common
Relay NO
Relay NC
+10V
0...10V
GND
Din1
16

13 Accessory overview
3
4
5
9
6
4
7
8
2
1
10
1. SG: Protection grille
2. ESD-F: Inlet cone
3. RSA: Silencer
4. EVH: Flexible connection
5. MPR: Mounting ring for vertical installation through a
roof
6. WSD: Weather protection roof
7. LRK: Airflow shutter
8. GFL: Counter flange
9. MFA: Mounting foot
10. FSD: Spring vibration damper for horizontal installation
Note:
For more information about accessories, refer to www.systemair.com or speak to Systemair technical support.
17

14 EU Declaration of Conformity
We, the manufacturer
Company Systemair GmbH
Address Seehöfer Straße 45
97944 Boxberg
Germany
declare under our sole responsibility that the product
Product designation Thermo fans — AxZent
Type/Model AxZent 400–630
AxZent 400–630EC
Identification Serial numbers dating from 2021 and onwards
fulfils all relevant provisions of the
Machinery directive 2006/42/EC
DIN EN ISO 12100:2013
Safety of machinery - General principles for design Riskassessment and risk reduction
DIN EN 60204-1:2019-06
Safety of machinery - Electrical equipment of machines - Part 1: General requirements
Directive electromagnetic
compatibility (EMC)
2014/30/EU
DIN EN IEC 61000-6-1:2019-11
Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity for
residential, commercial and light-industrial environments
DIN EN IEC 61000-6-4:2019-11
Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Immunity for
industrial environments
RoHS directive 2011/65/EU
IEC 63000:2016
Technical documentation for the assessment of electrical and electronic products with
respect to the restriction of hazardous substances
Person authorized to compile the technical file:
Matthias Hennegriff
Technical Director
This declaration relates exclusively to the machinery in the state in which it was placed on the market and excludes
components which are added and/or operations carried out subsequently by the final user. Boxberg, Germany 2021–11–10
Stefan Fischer
Managing Director
18