System air LCD display for SENSE User manual

14:3311
0
°C
.
!
CO 2
OK
14:33
22
0
°C
.
11
0
°C
.
!
CO 2
OK
14:33
22
0
°C
.
11
0
°C
.
!
CO 2
OK
14:33
22 0
°C
.
11 0
°C
.
!
CO 2
OK
UP and DOWN keys are for selecting current manual
mode. You can select changesby pressing OK key.
LCD display for SENSE
Up key
Down key
Back
key
Menu/OK Outdoor
temperature
Extract
temperature
Status
bar
Operating
mode
HOME PAGE
STATUS BAR MANUAL MODE SCREEN
QUICK MENU
MAIN MENU
Time
16.5°C 22.0°C
21.3°C
-11.0°C
°C
!
CO 2
Outdoor air
temperature
Supply air
temperature
Extract air
temperature
Exhaust air
temperature
*Setpoint for Minimal, Medium and Nominal .
Display brightnes
settings
Night display settings:
Display dims in
the dark
Screen dims in
light darkness
Screen dims in
hard darkness
Turn off night mode
– screen is always
ON.
Boost function
activation
Selecting AUTO mode
(Time scheduler) or
Manual mode
Setting of Time
Schedule
Review and
acknowledge of alarms
Settings:
KEYBOARD LOCK
Keyboard lock disables operatoin of the keys and than prevents
unauthorized personel from changing settings.
Active alarm
(warning/fault)
Current status
ON/OFF
Keyboard locked
status
Active mode
AUTO/MANUAL
CO2Air quality indicator
While pressing button or you can scroll between modes.
2sek
!
!
CO2
CO2
Function is activated with pressing and
OK
for 2 seconds. In status bar is showed
simbol , Which mean keyboard is
locked. Operation of the keys is disabled.
For deactivation of function, again
simultaneously press
OK
and for 2 seconds.
In settings, it is possible to turn automatic
key lock after 15 minutes (min. 2 min –
max. 2h) of inactivity.
!
Night display
settings
Lock/Unlock
keyboard
System info
Setpoint settings for temperature
Time settings
Date settings
Lor
Entering of Quick menu is
done with the key . Key
is for selecting between
Temperature view and Alarm
screen. With k
OK
ey Home
menu is availlable.
i

1
14:33
22
0
°C
.
11
0
°C
.
!
CO 2
OK
OK
SYNCHRONIZATION
FIRST START
CHANGE OF MODBUS ADDRESS
SYSTEM ALARMS
Switch off power supply
by switching main swith
on the SENSE unit.
System synchronization.
Wait few seconds...
When synchronization is finished,
HMI is ready to use.
Switch on power supply
on the SENSE unit.
Enter menu for change of modbuss address
On first start, when HMI is
connected with controller,
display for changeing
Modbus address of the HMI is
displayed.
With keys and
select Modbus address of HMI. With key
acknowledge selection.
8sek
In menu for changing of Modbuss address is possible to enter in first
minute while HMI is powered. By simunltaneously pressing two keys
and for 8 second, you will enter menu.
S01 – Error in data connection between controller and HMI. Check if the data cable is correctly
connected to the connector on SENSE unit and HMI. When the cause of the error is removed,
the error is automatically acknowledged.
S02 – Touch screen error. In the case of this error, HMI or controller must be serviced.
Only trained personnel is authorized to
operate with main switch.
Factory set is 2.
LCD display for SENSE
First start
1
14:33
22
0
°C
.
11
0
°C
.
!
CO 2
OK
OK
OK
SETTING OF MODBUS ADDRESS
!
!
S01