System Build 7461315COM User manual

7461315COM
2 Door / 1 drawer Base Cabinet
- Unit can tip over causing severe injury or death.
- Anchor unit to stud in wall (if instructed to).
- Do Not allow children to climb on unit.
- Put heavy items on lower shelves or drawers.
B347461315COMT1
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
WARNING
For the latest information on SystemBuild products
follow us at Ameriwood Home
Tube
You
Date of Purchase ___ / ___ / ___
Lot Number:
Do Not Return This Product!
Contact our customer service team for help first.
Call: 1-866-452-4081 (toll free)
Monday-Friday 9am - 5pm CST
Visit: www.systembuild.com
Assembly Difficulty Meter
Easy Tough

Contact Us!
Helpful Hints
2
systembuild.com
Do NOT return this product!
Contact our friendly customer service team first for help.
Call us!
1-866-452-4081
Monday-Friday
9am - 5pm CST
Visit systembuild.com to view the
limited warranty valid in the U.S. and Canada.
Assembly Tips
- Open your item in the area you plan to keep it to avoid excessive heavy lifting.
- Identify, sort and count the parts before attempting assembly.
- Compression dowels are lightly tapped in with a hammer.
- Slides are labeled with a R (right) and L (left) for proper placement.
- Make sure to always face the point on the top of the Cam Lock towards the
outer edge.
- Use all the nails provided for the back panel and spread them out equally.
- Back panel must be used to make sure your unit is sturdy.
- Do NOT use harsh chemicals or abrasive cleaners on this item.
- Never push, pull, or drag your furniture.
Tube
You
Tube
You
PEOPLE NEEDED FOR ASSEMBLY: 1-2
ESTIMATED ASSEMBLY TIME: 1 HOUR

3
systembuild.com
Before You Start
P
Quick
Tip
Assembly
P
P
P
Cam Lock Fastening System
This Cam Lock Fastening System will be used throughout the assembly process.
1
3
2
4
Tube
You
Read through each step carefully and follow the proper order
Separate and count all your parts and hardware
Give yourself enough room for the assembly process
Have the following tools: Flat Head Screwdriver, #2 Phillips Head
Screwdriver and Hammer
Caution: If using a power drill or power screwdriver for screwing,
please be aware to slow down and stop when screw is tight.
Failure to do so may result in stripping the screw.
P

4
systembuild.com
Board Identification
Not actual size
Left Panel
37461315010
Right Panel
37461315020 Top
37461316030
Bottom
37461315040
Back Rail
37448316050
Drawer Front
37461315060
Left Door
37461315070 Right Door
37461315080
Left Drawer Side
37461316090
Right Drawer Side
37461316100 Drawer Back
37461316110
Drawer Bottom
37461316120
AB
CD
E
FGH
I
JKL

5
systembuild.com
Parts List
DESCRIPTION
PART NUMB
QTY
ITEM
LEFT PANEL374613150101A
RIGHT PANEL374613150201B
TOP
374613160301
C
BOTTOM374613150401D
BACK RAIL374483160501E
DRAWER FRONT374613150601F
LEFT DOOR374613150701G
RIGHT DOOR
374613150801H
LEFT DRAWER SIDE374613160901I
RIGHT DRAWER SIDE
374613161001J
DRAWER BACK
374613161101K
DRAWER BOTTOM
374613161201
L
DRAWER BRACE
374610001301M
ADJ SHELF
374613161401N
STRINGER374613151501O
BACK PANEL
K744756011P
Board Identification
Not actual size
Drawer Brace
37461000130 Adjustable Shelf
37461316140
Stringer
37461315150
Left Panel
37461315010
This piece is paperboard
construction. It is not made from
wood, but is required for the
assembly of your unit.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
MNOP

6
systembuild.com
Part List
Actual Size
Not Actual Size
(x7)
#A22620
cam lock
(x7)
#A22610
cam bolt
(x4)
#A80250
shelf support
(x2)
#A11120
1/2" pan head
(x40)
#A21110
nail
(x3)
#A13800
2-1/4" flat head
(x4)
#A13410
1-3/4" flat head
(x22)
#A11600
1-1/4" flat head
(x24)
#A12100
7/16" pan head
(x6)
#A23700
vinyl cap
(x3)
#A21520
compression dowel
(x3)
#A52995
handle
(x4)
#A65615
hinge
(x1)
#A84050
safety bracket kit
23
456
78
910
11
12 13
14
14a
14d
14c
14b
1

7
systembuild.com
Part List
Not Actual Size
(x4)
#A43610
leg mount
(x2)
#A92510
base plate
(x1)
#A55015
lock
(x4)
#A43600
adjustable leg
(x1)
#A56100
drawer slide
(x2)
#A54220
drawer bracket
16
15 17
19
20
18

8
systembuild.com
STEP1
20
(x1)
#A56100
Extend the slide as shown. Press the release lever and remove the inner slide.
release lever
Use these holes to fasten to the left and right panels (A&B).
Use these holes to fasten to the left and right drawer sides (I&J).
inner slide

9
systembuild.com
STEP2
Position the drawer slide (without inner slide) from step 1 as shown. Start by attacing the slide at
the rear. While sliding the middle of the slide locate the holes in the panels with the access hole
in the slide and fasten with screws (4) as shown.
2420
(x2)
#A22620
(x1)
#A22610
(x3)
#A12100 (x1)
#A56100
2
4
20
A
1
1
Proper orientation of CAM LOCK
Tip
Assembly
Quick

10
systembuild.com
STEP3
2420
4
2
Position the drawer slide (without inner slide) from step 1 as shown. Start by attacing the slide at
the rear. While sliding the middle of the slide locate the holes in the panels with the access hole in
the slide and fasten with screws (4) as shown.
(x2)
#A22620
(x1)
#A22610
(x3)
#A12100 (x1)
#A56100
20
B
1
1
Proper orientation of CAM LOCK
Tip
Assembly
Quick

11
systembuild.com
STEP4
loosen to separate
13
(x4)
#A65615
13
A
B
13
13

12
systembuild.com
STEP5
raw surface
7
2
14a 14b
(x3)
#A13800
(x4)
#A22610
(x1)
#A84050
2
7
2
2
2
7
7
14a
14b
C
E
Be sure the back rail (E) is centered on the top (C).
Do not tighten scerw.

13
systembuild.com
STEP6
10
(x2)
#A22620 (x2)
#A21610
10
10
O
Approx.
7/16"
10
1
1
1
Proper orientation of CAM LOCK
Tip
Assembly
Quick

14
systembuild.com
STEP7
Note: All finished edges face up.
A
B
O
UNLOCKLOCK

15
systembuild.com
STEP8
finished edge
A
OB
C
D
8
8
8
8
8
(x4)
#A13410
UNLOCKLOCK

16
systembuild.com
STEP9
Fasten the leg mount (16) to the bottom (D) with screws
(9). Press the leg sleeve (15) into the leg mount (16).
Screw the adjustable leg (15) completely into the leg
sleeve (15).
9
15
16
(x4)
#A11600
(x4)
#A43600
(x4)
#A43610
9
16 15
D

17
systembuild.com
STEP10
Carefully turn your unit over on its front side. Assure that the unit is square. Distance from
corner to corner must be equal as shown. Attached the back panel as shown nailing straight into
the raw edges.
IMPORTANT! THE BACK PANEL IS A STRUCTURAL PART OF THIS UNIT
AND MUST BE INSTALLED PROPERLY.
(x34)
#A21110
6
6
raw surface
shown
notch for safety bracket
Assure that the unit
is square.
Flush the edge of the back panel with
the bottom edge of the bottom shelf.
Align squarely and nail straight
through into back edges.

18
systembuild.com
STEP11
Lay the drawer sides down on a flat hard surface. Carefully line up the drawer bracket with the
holes in the drawer side as shown. Using a hammer, tap each bracket stem part way into each
hole. Repeat process until the drawer bracket is fully seated on the drawer side.
19
(x2)
#A54220
19 19
I
J

19
systembuild.com
STEP12
4
(x6)
#A12100
(x2)
#A56100
(inner slide from step 1)
44
I
J

20
systembuild.com
STEP13
Be sure groove in drawer sides line up with grove in drawer front.
2410
(x1)
#A22620
(x1)
#A22610
(x4)
#A12100
(x1)
#A21520
Approx.
7/16"
10
2
4
10
I
J
F
M
1
1
Proper orientation of CAM LOCK
Tip
Assembly
Quick