System Sensor RTS151KEYA User manual

D440-03-00 1 I56-3475-000
RTS151KEYA
Remote Test Station
INSTALLATION AND MAINTENANCE INSTRUCTIONS
6581 Kitimat Road, Unit 6, Mississauga, Ontario L5N-3T5
1-800-SENSOR2, FAX: [phone]
www.systemsensor.ca
NOTE: RTS151KEYA replaces RTS451KEYA.
NOTICE: This manual shall be left with the owner/user of this equipment.
NOTE: A test coil is required only for use with D2A,DNRA,DH400A,DH500A
models. For D2A models order part # DCOIL. For DH400A/500A models
order part #Coil.
GENERAL INFORMATION
The System Sensor RTS151KEYA is an automatic fire detector accessory
designed to test remotely located duct and beam detectors. For 4-wire detec-
tors, the RTS151KEYA features a multi-colored LED that alternates between
steady green and red. Green indicates power and that the detector board is
in place. Red indicates alarm. For 2-wire detectors, the LED will show red for
alarm. Consult the detector installation instructions for additional information.
The National Fire Protection Association and CAN/ULC-S536 has published
codes, standards, and recommended practices for the installation and use
of this product. It is recommended that the installer be familiar with these re-
quirements, with local codes, and any special requirements of the local au-
thority having jurisdiction.
RTS151KEYA CONTENTS
1 RTS151KEYA remote test station
1 screw pack (2 mounting screws)
2 Keys
OPERATION
Test Function
Insert the key and turn clockwise to the “TEST” position.
Alarm Indication
With the key in the “TEST” position, some time will elapse (40 seconds maxi-
mum) depending on the detector type, before the alarm indicating LED will
turn red.
Reset Function
Turn the key counterclockwise to the “RESET” position and hold. The LED
should turn off. Then, turn the key back to the “NORMAL” position and re-
move. The RTS151KEYA is capable of resetting only certain models of detec-
tors. Refer to the detector installation instructions for additional information.
Wiring Instructions
Consult the appropriate detector installation instructions for the applicable
wiring diagram. The RTS151KEYA mounts to a single gang box (2 1/2˝ mini-
mum depth), or directly to the wall or ceiling.
In Canadian applications, the RTS151KEYA is intended to be located in the
same room as the smoke detector and within 60 feet of the unit.
OFF
RESET TEST
H0195-01
H0582-13
FIGURE 1. RTS151KEYA
FIGURE 2: WIRING DIAGRAM FOR RTS151KEYA TO D4120A
4-WIRE DUCT SMOKE DETECTOR:
FIGURE 3: WIRING DIAGRAM FOR RTS151KEYA TO D2A 2-WIRE
DUCT SMOKE DETECTOR:
SPECIFICATIONS
Dimensions: 4.6˝ H × 2.75˝ W × 1.8˝ D
Weight: 0.24 Lbs.
Power Requirements
Power LED (Green): 14 – 35 VDC, 12 mA maximum
Alarm LED (Red): 2.8 – 32 VDC, 12 mA maximum
Alarm Response Time: 40 seconds maximum
Temperature: –10°C to 60°C (14°F to 140°F)
Humidity: 95% relative humidity, noncondensing Max
2
6
1
5
4
3
D4120A
RTS151KEYA
(GREEN LED)
POWER
(RED LED)
ALARM
FIELD
INSTALLED
JUMPER
AUX OUT +
AUX OUT –
ALARM
R TEST
R RESET
SUP, NO
SUP, C
* Sup. contacts cannot be used if they are wired to control panel.
*
EXTERNAL
(-) POWER (+)
SUPPLY
*
RTS151KEYA
REMOTE TEST STATION
LED OPTION
1 PER UNIT
10mA CURRENT DRAW
TEST COIL OPTION
1 PER UNIT
95mA CURRENT DRAW
4 5
321
TEST COIL +
TEST COIL –
COMM +
OUT (CONV ONLY) +
COMM –
RA/RTS –
RA +
RTS +
NOTE: THE RTS151KEYA TEST COIL
CIRCUIT REQUIRES AN EXTERNAL 24 VDC
POWER SUPPLY WHICH MUST BE UL LISTED.
NOTE: THE USE OF A REMOTE TEST STATION REQUIRES THE
INSTALLATION OF AN ACCESSORY COIL, PART NUMBER DCOIL,
SOLD SEPARATELY.
H0571-10

D440-03-00 2 I56-3475-000
©2009 System Sensor
Three-Year Limited Warranty
System Sensor warrants its enclosed product to be free from defects in materials and
workmanship under normal use and service for a period of three years from date of
manufacture. System Sensor makes no other express warranty for the enclosed prod-
uct. No agent, representative, dealer, or employee of the Company has the authority to
increase or alter the obligations or limitations of this Warranty. The Company’s obliga-
tion of this Warranty shall be limited to the replacement of any part of the product which
is found to be defective in materials or workmanship under normal use and service
during the three year period commencing with the date of manufacture. After phoning
System Sensor’s toll free number 800-SENSOR2 (736-7672) for a Return Authorization
number, send defective units postage prepaid to: System Sensor, Returns Department,
RA #__________, 6581 Kitimat Road, Unit 6, Mississauga, Ontario L5N-3T5. Please
include a note describing the malfunction and suspected cause of failure. The Company
shall not be obligated to replace units which are found to be defective because of dam-
age, unreasonable use, modifications, or alterations occurring after the date of manufac-
ture. In no case shall the Company be liable for any consequential or incidental damages
for breach of this or any other Warranty, expressed or implied whatsoever, even if the
loss or damage is caused by the Company’s negligence or fault. Some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This Warranty gives you specific legal rights,
and you may also have other rights which vary from state to state.
FIGURE 5. WIRING DIAGRAM FOR RTS151KEYA TO DH100ACDC
4-WIRE DUCT SMOKE DETECTOR:
FIGURE 4: WIRING DIAGRAM FOR RTS151KEYA TO DNRA 2-WIRE DUCT SMOKE DETECTOR:
FIGURE 6. WIRING DIAGRAM FOR RTS151KEYA TO DH100 2-WIRE
DUCT SMOKE DETECTOR:
NOTE: Terminal 6 of the RTS151KEYA is not used when wired to a 2-wire detector.
15
19
14
3
20
2
11
2
6
1
Alarm Signal
Aux. Power +
Sup. N. O.
Sup. COM
Aux. Power –
Reset
Test
(Red LED) Alarm
(Green LED)
Power
DH100ACDCLPA RTS151KEYA
5
4
3
*
* Sup. contacts
cannot
be used if they are
wired to control
panel.
1
2
3
4
5
6
3
4
5
Test +
Test / Reset –
Reset +
Test
Reset
RA +
RA –
V Out +
DH100 RTS151KEYA
6
2
1Alarm
LED
No Connection
H0193-05
H0612-10
H0156-08
FIGURE 7. WIRING DIAGRAM FOR RTS151KEYA TO DH400ACDCA
DUCT SMOKE DETECTOR:
5
7
11
10
6
3
4
2
6
1
Alarm Signal
Aux. Power +
Sup. N. O.
Sup. COM
Aux. Power –
Reset
Test
(Red LED) Alarm
(Green LED)
Power
DH400ACDCA RTS151KEYA
5
4
3
*
* Sup. contacts
cannot be used if
they are wired to
control panel.
H0156-09
FIGURE 8. WIRING DIAGRAM FOR RTS151KEYA TO BEAM1224A/
BEAM1224SA SMOKE DETECTOR:
H0585-04
3
2
1
5
4
RTS151KEYABEAM1224A/BEAM1224SA
REMOTE ALARM OUT
AUX (–)
TEST INPUT
REMOTE TROUBLE OUTPUT
RESET INPUT
TEST
RESET
T2-3
T3-3
T2-4
T2-2
T2-1
OPTIONAL YELLOW LED
NOTE: RTS151KEYA CAN BE USED WITH INTELLIGENT BEAM DETECTOR PRODUCTS.
CONSULT INTELLIGENT BEAM DETECTOR MANUAL FOR ADDITIONAL INSTRUCTIONS
(RED LED) ALARM
24 VAC (+10%, –15%)
FULL WAVE RECTIFIED,
UNFILTERED POWER
MAY BE USED
RTS151KEYA
(OPTIONAL) REMOTE
TEST STATION
MAGNET
TEST
SWITCH
ALARM
LED (RED)
4
5
2
1(+)
(–)
+ RA
+ RTS
– RA
+ TEST COIL
– TEST COIL
+ IN
+ OUT
–
(–)
(+)
DNRA
24 VDC
AUX POWER
SUPPLIED
BY USER
(100mA
SUPPLY)
RTS151KEYA
(OPTIONAL) REMOTE
TEST STATION
24 VAC (+10%, –15%)
FULL WAVE RECTIFIED,
UNFILTERED POWER
MAY BE USED
MAGNET
TEST
SWITCH
ALARM
LED (RED)
4
5
2
1(+)
(–)
+ RA
+ RTS
– RA
+ TEST COIL
– TEST COIL
+ IN
+ OUT
–
24 VDC
AUX POWER
SUPPLIED
BY USER
(100mA
SUPPLY)
DNRA
NOTE: THE USE OF THE RTS151KEYA REQUIRES THE INSTALLATION OF
AN ACCESSORY COIL, DCOIL, SOLD SEPARATELY.
METHOD #1 - AUX POWER LOCATED
AT DUCT DETECTOR
METHOD #2 - AUX POWER LOCATED
AT TEST STATION