SystemBase Eddy User manual

1
Eddy Serial
User Guide
Ver 2.1.1.1
2010. 06.25

2
Revision History
Revision Date Document Version Pages Description
Feb-5-2009 2.1.0.1 All Initial release by shlee
Sep-10-2009 2.1.0.2 4,5,6 Added WiFi
Nov-11-2009 2.1.0.3 2,3,5 Append Eddy-S4M
Jun-06-2010 2.1.1.1 All Open Linux Version
Added Eddy-BT

3
Table of Contents
Chapter 1. Introduction ...............................................................................................................................5
1.1 About this manual....................................................................................................................................................5
1.2 Who should read this manual.....................................................................................................................................5
1.3 Contents.................................................................................................................................................................5
1.4 Eddy Documents ..................................................................................................................................................... 6
1.5 Technical Support .....................................................................................................................................................7
Chapter 2. Getting Started...........................................................................................................................8
2.1 Overview............................................................................................................................................................... 8
2.2 Eddy-CPU v2.1 ........................................................................................................................................................ 8
2.3 Eddy-DK v2.1 (Development Kit)................................................................................................................................ 9
2.4 Eddy-S4M v2.1.......................................................................................................................................................11
2.5 Eddy-S4M-DK v2.1 (Development Kit) ........................................................................................................................13
2.6 Eddy-S4M-JiG v2.1 (Testing Board)........................................................................................................................... 14
2.7 Eddy-WiFi v 2.1......................................................................................................................................................15
2.8 Eddy-BT v2.1..........................................................................................................................................................17
2.9 Eddy Software Architecture...................................................................................................................................... 18
2.10 Main Features....................................................................................................................................................... 18
2.11 Applications............................................................................................................................................................19
Chapter 3. Hardware Description.................................................................................................................. 20
3.1 Eddy-CPU .............................................................................................................................................................20
3.2 Eddy-DK v2.1 .........................................................................................................................................................21
3.3 Eddy-S4M v2.1...................................................................................................................................................... 23
3.4 Eddy-S4M-DK v2.1.................................................................................................................................................24
3.5 Eddy-S4M-JIG v2.1................................................................................................................................................. 25
3.6 Eddy WiFi v2.1....................................................................................................................................................... 26
3.7 Eddy BT v2.1.........................................................................................................................................................28
Chapter 4. Integration............................................................................................................................... 30
4.1 Connection Guide....................................................................................................................................................30
4.2 First-time Bootup ..................................................................................................................................................30
4.3 Connecting to Eddy with IP address...........................................................................................................................30
4.4 Using MCI slot & USB Host Port ............................................................................................................................... 33

4
Chapter 5. Configuration via Web..................................................................................................................36
5.1 Connection............................................................................................................................................................ 36
5.2 Setup Menu.......................................................................................................................................................... 37
5.3 Network Settings...................................................................................................................................................39
5.4 Serial Settings....................................................................................................................................................... 41
5.5 Wireless Settings ...................................................................................................................................................44
5.6 Peripheral Settings .................................................................................................................................................47
5.7 DIO Settings..........................................................................................................................................................50
5.8 SNMP Settings........................................................................................................................................................51
5.9 Change Password ................................................................................................................................................... 52
5.10 Update Firmware ................................................................................................................................................... 53
5.11 Factory Default...................................................................................................................................................... 54
5.12 Save & Reboot .....................................................................................................................................................54
Chapter 6. Configuration via Telnet................................................................................................................56
6.1 Connection............................................................................................................................................................ 56
6.2 View commands..................................................................................................................................................... 56
6.3 Network commands................................................................................................................................................ 57
6.4 WiFi commands...................................................................................................................................................... 59
6.5 Serial Commands....................................................................................................................................................60
6.6 Username/Password Commands................................................................................................................................. 61
6.7 System Commands.................................................................................................................................................. 62
Chapter 7. apendix ...................................................................................................................................63
7.1 Firmware Updates via FTP........................................................................................................................................ 63
7.2 Ordering Information...............................................................................................................................................64
7.3 FCC Statement .......................................................................................................................................................64

Eddy User's Guide
5
Chapter 1. Introduction
Eddy, SystemBase Embedded Device Server Module, is an optimized minimal CPU module for developing an industrial embedded device. This manual introduces
general factions for the Eddy.
1.1 About this manual
This manual guides that users are able to develop Eddy for a device server including the function that transfers from serial data to LAN. Setting Eddy’s
configurations, status monitoring, firmware update, and other administration work are also included, H/W level integration and S/W setting information can also
be found.
1.2 Who should read this manual
This guide is designed for Eddy users and administrators. It is strongly recommended that anyone trying to apply, use, and maintain Eddy read this document.
It will be a great starting point for any administrator who wants to easily monitor and control Eddy and its connected devices.
1.3 Contents
Chapter 1. Introduction is a preface with general information and introductory notices.
Chapter 2. Getting Started gives a brief introduction to Eddy series, including features and applications.
Chapter 3. Hardware Descriptions explains the layout and pin specifications with block diagram and drawings.
Chapter 4. Integration assists you connecting Eddy to serial and network environment. It covers first time boot-up and status check procedures.
Chapter 5. Configuration via Web provides ways to configure and to connect Eddy via web browser.
Chapter 6. Configuration via Telnet provides commands and its explanation to configure and to connect Eddy via web Telnet.
Chapter 7. Appendix provides firmware update guides and detailed technical specifications.

Eddy User's Guide
6
1.4 Eddy Documents
The following table summarizes documents included in the Eddy document set.
Document Description
Eddy Serial User Guide Eddy’s Configuration, and Management Information
Eddy DK Guide
Programmer’s application development guide, including in-depth approach to compiling,
linking, creating and uploading firmware
API reference is included with a list of available functions
for customized application programming
LemonIDE User Guide User manual about Eddy integrated development environment of Window/Linux based on Eclipse
Portview User Manual Guide for SystemBase device server management application Portview
COM Port Redirector
User Manual Guide for SystemBase COM Port Redirector
TestView
User Manual Guide for SystemBase test program TestView
General information on Eddy or embedded device servers can be obtained at our website at http://www.sysbas.com/. Latest documents, software and
firmware downloads are available.
Other relevant documents are as follows:
Document Description
Eddy-CPU Spec Sheet Eddy-CPU spec description
Eddy-S4M Spec Sheet Eddy-S4M spec description
Eddy-WiFi Spec Sheet Eddy-WiFi spec description
Eddy-BT Spec Sheet Eddy-BT spec description
LemonIDE Spec Sheet integrated development environment description
Eddy White Paper An introductory reading for anyone new to embedded device server, which focuses on
background, history, market environment, and technology
All documents are updated promptly, so check for the recent document updates. The contents in these documents are subject to change without a prior
notice.

Eddy User's Guide
7
1.5 Technical Support
You can reach our tech support by following 3 ways;
1. Visit the Eddy official community site at http://www.embeddedmodule.com and go to ‘Technical Support’ menu. FAQ and questions can be reviewed
and submitted.
2. E-mail our technical support team to [e-mail]. Any kind of inquiries, requests, and comments are welcomed.
3. Call us at our customer center at 82-2-855-0501 for immediate support.
Our technical support team will kindly help you get over with the problem.

Eddy User's Guide
8
Chapter 2. Getting Started
Welcome to Eddy! This chapter includes Eddy series overview, main and distinctive features, package contents for each product, and application fields.
2.1 Overview
There are two categories in Eddy; Eddy-CPU module, Eddy Development Kit (DK).
Eddy-CPU modules include category of socket type Eddy-CPU and Mini PCI type Eddy-S4M.
Eddy-DK includes DK board for Eddy-CPU exclusive, JIG and DK board for Eddy-S4M exclusive.
The Eddy-CPU module includes default applications for serial and LAN communication, and supports plug-and-play features. By switching to the custom mode,
users can program any application and upload it on to the module. This application then is executed on the module. In order to write and compile
programmer’s source code, Software Development Kit (SDK) LemonIDETM is required.
SDK is included in the DK package. Please refer to Programming Guide and LemonIDETM user’s manual included in the Development Kit for detailed
information on the SDK.
SDK is not necessary for users using Eddy in default presettings.
2.2 Eddy-CPU v2.1
Eddy-CPU is an embedded module based on ATMEL AT91SAM9260-CJ processor with 32MB SDRAM, 4MB or 8MB Flash Memory, 1 Ethernet port with
10/100Mbps, 16 bit address / 8 bit data bus interface supporting external device connection, and maximum 17 programmable IO pins. Programmers can easily
implement any device drivers with referring to library type example codes and evaluation kit circuit diagrams.
User can design their own customized device using example sources and Evaluation Kit circuit.
Eddy-CPU is implemented on a small form factor (42 * 25mm) with on-board memory and integrated 10/100Mbps network interface. Developers can minimize
time and cost spent on developing application products.
Feature Type
CPU ARM926EJ-S (210 MHz)
Memory 8MB Data Flash, 32 MB SDRAM
Hardware
External I/F 19 Bit / 16 Bit Data Bus

Eddy User's Guide
9
Feature Type
Ethernet I/F 10/100 Base-T Auto MDI/MDIX
UARTs 4 Port, Support up to 921.6 Kbps
(1 : Full Signal, 2,3,4, : RxD, TxD, RTS, CTS only)
USB 2.0 FS 2 Host /1 Device Port, 2.0 FS (12Mbps)
ADC 4-Channel 10 Bit ADC
TWI(I2C) Master, Multi-Master and Slave Mode
SPI 8- to 16-bit Programmable Data Length
Four External Peripheral Chip Selects
GPIO Max. 56 Programmable I/O Pins
Power Input 3.3 V (200 mA Max)
Dimensions 25 x 48.5 x 6.2 mm
Weight 8.3 g
Protocol TCP, UDP, Telnet, ICMP, DHCP, TFTP, HTTP, SNMP 1&2, SSH, SSL
Ethernet 10/100Mbps MAC / PHY
Network
Network Connection Static IP, DHCP
O/S Linux Kernel 2.6.21
Mgt Tools SNMP, Web, PortView
Uploads TFTP, FTP, Web
Software
Dev Tools LemonIDE & SDK
Operating Temp -40 ~ 85 ℃
Storage Temp -60 ~ 150 ℃
Environmental
Humidity 5 ~ 95% Non-Condensing
Approvals
CE Class A,
FCC Class A,
RoHS compliant
2.3 Eddy-DK v2.1 (Development Kit)
Eddy Development Kit (Eddy DK) helps programmers to test and customize their own Eddy applications easily. The kit includes evaluation board, all necessary
connectors, and programming environment with documentations and guidelines. Please refer to Eddy DK Manual included in the Development Kit for detailed
information on the DK.

Eddy User's Guide
10

Eddy User's Guide
11
Feature Type
NAND Flash 256MB, 8bit I/F
SD Card
Connector
Push Type, Up to 16 GB
MMC / SD Card / MC supported
USB Connector 1 x Device
2 x HOST, Dual-Port
LCD Module 128 x 64 Dots Matrix Structure
KEY 4 x 4 Matrix
Battery Holder 3V Lithium Battery, 235 mAh
LED Power, Ready, 20 Programmable IO, Console & Serial TxD, RxD
I2C Interface 16bit I2C BUS GPIO
SPI Interface 2Kbit EEPROM
MCI Interface SD Card, MMC Socket
ADC Interface Temp / Light Sensor
Digital I/O 8 Port Input, 8 Port Output
Switch
Serial or GPIO Select
RS422/485 Select
DIO : Common VCC or GND Select
Programming
Jumper Switch Boot Mode Select, JTAG Select
Serial Port
2 x RS232 DB9 Male
2 x RS422/485 Terminal Block
(RS422 & RS485 Selected by S/W)
Console Port DB9 Male
LAN Port 2 x RJ45
ICE Port Used for Flash Programming
Reset Button Factory Default & Warm Boot
Input Power 9-48VDC
Dimensions 240 x 180 mm
2.4 Eddy-S4M v2.1
Eddy-S4M is a high-performance mini PCI type embedded module which include ATMEL AT91SAM9260-CJ processor 32MB SDRAM, 8MB DataFlash, 10/100Base-T
Ethernet port, Serial 4 Channel, RTC with Battery, microSD, 4ch ADC, temperature sensor, max 34 programmable GPIO pins.
Eddy-S4M is 59.75 x 61.8mm size. If using Eddy-S4M-JIG board, user could develop their customized device without other H/W development, which
minimizing time and cost to develop.
Referring Example code and Evaluation Kit circuit allow developer to design device they want.

Eddy User's Guide
12
Classification Specification
CPU ARM9260B-CJ (210 MHz)
Memory AT45DB642D, 8MB Data Flash
IS42S16160B, 32 MB SDRAM
Ethernet MC/PHY 10/100 Base-T MAC
KSZ8041NLi PHYceiver Auto MDI/MDIX
Serials
Port 0,1 : RS232 (DB9 male)
Port 0 : Full Signal
Port 1 : TxD, RxD, RTS, CTS only
Port 2,3 : COMBO (Terminal Block 5pin)
* COMBO : RS422/RS485 is S/W selectable
USB 2.0 FS 3 Host /1 Device Port, 2.0 FS (12Mbps)
Use to GL850A USB Hub chip
RTC Real Time Clock, RTC DS1340U-33+
Connect to I2C I/F
Battery Holder CR1220(38mAh) 3V Lithium Battery
ADC 4-Channel 10 Bit ADC
TWI(I2C) Master, Multi-Master and Slave Mode
SPI 8 to 16-bit Programmable Data Length
Four External Peripheral Chip Selects
MCI SD Spec V2.0 [SDHC], MMC Spec V4.2 support
USB to SD Controller, 16GB, 12Mbits/s
GPIO Max. 34 Programmable I/O Pins
Hardware
LED Ready LED
Protocol TCP, UDP, Telnet, ICMP, DHCP, TFTP, HTTP,
SNMP1&2, SSH, SSL
Network Connection Static IP, DHCP
O/S Linux Kernel 2.6.21
Mgt Tools SNMP, Web, PortView
Uploads TFTP, FTP, Web
Software
Dev Tools LemonIDE & SDK
Power Input 3.3 V (200mA Max)
Physical
characteristics Dimensions 59.75 x 61.80 x 4 mm

Eddy User's Guide
13
Classification Specification
Weight 15 g
Operating Temp -40 ~ 85°C
Storage Temp -66 ~ 150°C
Environment
Humidity 5 ~ 95% Non-Condensing
CE Class A,
FCC Class A,
RoHS compliant
2.5 Eddy-S4M-DK v2.1 (Development Kit)
Eddy-S4M DK is Development Kit supporting programmer can easily materialize and test their application.
DK includes Test Board, various connectors, programming environment and document. Please refer to Eddy-DK manual for more specific explanation of Eddy-
S4M
Classification Specification
Serial Port 2 x RS232 DB9 Male
2 x RS422/485 5pin Terminal Block (S/W Selectable & with Auto toggle)
SD Card Connector Push Type, Up to 16 GB
MMC / SD Card / MC supported
MCI Interface SD Card, MMC Socket
ADC Interface Light Sensor
USB Connector 1 x Device, 2 x HOST, Dual-Port
LAN Port RJ45 with transformer

Eddy User's Guide
14
Classification Specification
Console Port DB9 Male
Switch
Power ON/Off switch
Serial RS422/485 Termination resistor configuration switch
GPIO input test switch(Off : Low, ON : High)
LED RDY, Power, 34 Programmable IO, Console & Serial TxD, RxD LED
JTAG Port Used for downloading code and single-stepping through programs
Reset Button Factory Default & Warm Boot
(If pushing over 5sec, operate in Factory default)
JIG Connection Socket 2 2x23pin socket, which connect JIG board to confirm problems
Expansion Header 2x22pin Header, used to test GPIO of Eddy-S4M
Input Power 5 VDC
Dimensions 160 x 120 mm
2.6 Eddy-S4M-JiG v2.1 (Testing Board)
Eddy-S4M JIG board is test board which enable of user to integrate and test their application with Eddy-S4M. JIG board include mini connector for joining
Eddy-S4M, Ethernet RJ45, USB Host, Power, Reset Switch, and providing connectors to all Eddy-S4M functions.
For more information, please refer to Eddy-DK manual in DK product.
Classification Specification
USB Connector USB HOST
LAN Port RJ45 with Transformer
Reset Button Factory Default & Warm Boot
Expansion Header Used to connect most functions of S4M to externalS4M
Input Power 5 VDC
Dimensions 70 x 105 mm

Eddy User's Guide
15
2.7 Eddy-WiFi v 2.1
Eddy WiFi joined with Eddy-CPU, Eddy-S4M enables various serial devices (secure device, communication device, modem, print data device, industrial
measuring instrument) to connect wireless LAN.
Eddy-WiFi module supports IEEE 802.11 b/g wireless specification.
You can set the wireless network parameters. After changing values, you need to click [Submit] button. Then you will see the same page with modified
values. Please note that you have to [Save & Reboot] in order to see these changes in effect. Changes will be discarded if you do not save current
settings.
Classification Specification
Standard 802.11b, 802.11g
Modulation 802.11g: OFDM
802.11b: CCK,DQPSK, DBPSK
Frequency Band 802.11b/g:
ISM band 2.4GHz ~ 2.483.5GHz
RX sensitivity 802.11a/g: -68m @54Mbps 8% PER
802.11b: -85dBm @11Mbps 8% PER
Security WEP 64/128, WPA, WPA2
Working distance 60 - 120m, depending on surrounding
environment
Data Rate 802.11b : 11, 5.5, 2, 1 Mbps
802.11g : 54, 48, 36, 24,18,12,11, 9, 6, 5.5, 2 , 1 Mbps
Power consumption TX : 450mA
RX : 300mA
Host interface USB2.0
Antenna ANT 2.4Ghz, RP-SMA Female
Antenna Cable RF 100mm SMA B/H
Dimension 54 x 25 x 6mm
Operating Temp -20 ~ 50°C

Eddy User's Guide
16
Classification Specification
Humidity 5 ~ 90% Non-Condensing
Operating Voltages 3.3V±5%
Weight 10g
Approvals CE Class B, FCC Class B, RoHS Compliant
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation
Caution : Any changes or modifications in construction of this device which are not
expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
* If the Eddy-WiFi is installed inside of another device, then the exterior label of the
device must use such as the following:
“Contains Transmitter Module FCC ID: PROEddy-WiFi” or “Contains FCC ID: PROEddy-WiFi”
FCC RF RADIATION EXPOSURE STATEMENT
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body. This transmitter must not be co-located or
operated in conjunction with any other antenna or transmitter.
CE warning
!Changes and modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
EN Test Regulations
ETSI EN 300 328 V1.7.1
ETSI EN 301 489-1 V1.6.1
ETSI EN 301 489-17 V1.3.2
EN 60950-1:2006+A11:2009

Eddy User's Guide
17
2.8 Eddy-BT v2.1
Linking to Eddy-CPU and Eddy-S4M, Eddy-BT module enables communication with various types of Bluetooth device in Bluetooth method. Eddy-BT is based on
Bluetooth 2.0 and supports communication distance of up to 1,000m.
For the details of Eddy-BT, please refer to “Eddy DK Programming Guide”.
Classification Specification
Interface Bluetooth v2.0+ EDR Class 1
Profile SPP (Serial Port Profile)
Max, TX Power +18dBm
RX sensitivity -88dBm
Power Supply voltage: 3.3V DC
Supply current::10mA – 60mA
Operating Temp Operating temperature: -30 ~ 80 oC
Storage Temp Storage temperature: -40 ~ 85 oC
Humidity Humidity : 90% (Non-condensing)
Working distance
Stub Antenna (+1dBi) 100 meters
Dipole Antenna (+3dBi) 150 meters
Dipole Antenna (+3dBi) 200 meters
Dipole Antenna (+5dBi) 300 meters
Patch Antenna (+9dBi) 500 meters
Dipole Antenna (+5dBi) 400 meters
Patch Antenna (+9dBi) 600 meters
Patch Antenna (+9dBi) 1,000 meters
Approvals CE Class A, FCC Class A, RoHS Compliant

Eddy User's Guide
18
2.9 Eddy Software Architecture
2.10 Main Features
Various features of Eddy make it a universal yet distinctive embedded solution.
Below lists main features of Eddy.
l Premium-level hardware with ARM9 210MHz CPU, 8MB Flash, and 32MB SDRAM
l Selectable RS232 only or RS422/485 combo interfaces
l USB host port (Max 12Mbps USB Full speed)
l SD Card Interface
l Max 921.6Kbps serial speed
l Program and run your own application
l SystemBase SDK and API support for application programming (included in Development Kit)
l Small size to fit in to any hardware
l 10/100Mbps Ethernet port (auto MDIX)
l SystemBase COM Port Redirector for better adaptability
l Extensive configuration and monitoring with Portview
l Firmware upload with Web, FTP, and TFTP
l Configuration with Web, Telnet, SNMP, and Portview
l Various customizing options
l Standard Linux environment for openness in executable applications
l Multiple Programmable IO pins for customized applications
l Watchdog timer support for monitoring the system and reset when system error is occurred.

Eddy User's Guide
19
2.11 Applications
Eddy can be applied to many practical applications in various fields. Some are presented below.
◆ Factory / Industrial Automation
PLC, Robot arms, Human-Machine Interface, Warehouse rails
Medical instruments, Inspection equipment controllers
Alarming units
◆ Home Appliances / Electronic Devices
Power controller, Gaming machines
Scales, Gas detection units, Water & pollution metering devices
Data collection and distribution units
◆ Financial / Building Automation
Card readers, Barcode scanners, Kiosks, Point-Of-Sale related devices
Serial printers, Cash registers, Credit card authorization terminals
Biometric detection units, Security devices
◆ OEM Device Server Distributors
OEM device server with distributor’s own case & brand
Ready-to-go device or customized application / setup mode can be inserted

Eddy User's Guide
20
Chapter 3. Hardware Description
This chapter provides Eddy’s hardware information, including block diagram, layout, pin specifications, dimensions and other hardware-related issues.
3.1 Eddy-CPU
Ethernet port is provided as pin headers, and the transformer and RJ-45 connector should be manually implemented by users. (RJ-45 connector with
embedded transformer, normally called LAN-Mate or MAG Jack, can be used as a simpler approach.
Eddy CPU V2.1 Device Discription
Eddy CPU V2.1 Connector Discription