Taiga Concept LOHKO BOX 3 User manual

LOHKO BOX 3
ASSEMBLY
GUIDE
www.taigaconcept.com
x2
4,5h

Take image of the damaged item
before opening the package for
later documentation, then
continue opening package
If you find damage please
take images before
opening the package
Check if there is any damage
to the package
Remove top cover and check that
there are no signs of damage before
unpacking.
If you find damage please take
images before unpacking the product
elements
If you damage elements while carrying,
take images of the damages
If you damage elements
while assembling the product,
take images of damages
Assemble the product
Take image of the damage,
check which element / part
is damaged and contact
the local Taiga dealer
Take image of the damage,
check which element / part
is damaged and contact
the local Taiga dealer
Take image of the damage,
check which element / part
is damaged and contact
the local Taiga dealer
If you find damage, document with
photos according instructions
Carry the elements
Note: Take extra care
when carrying glass
2

3
1. Take images where you can see
full package from 2 different angles
which show the damage
1. Take images where you can see
full package from 2 different angles
which show the damage
1. Take images where you can see
the whole element from 2 different angles
which show the damage
2. Take closer images of the damage
2. Take closer images of the damage
2. Take closer images of the damage and
check which element / glass is damaged.
3. Contact your local Taiga dealer
3. Contact your local Taiga dealer
3. Contact your local Taiga dealer
How to document if you cause damage while carry orassembling the product

www.taigaconcept.comwww.taigaconcept.com
Installation
Open the packing carefully not to damage the
product.
Always follow assembly instruction when you
assemble your product.
When moving the glass elements make sure
you don’t place them on hard surfaces as they
will break easily.
When assembling the product make sure you
can support the wall element until they are
stable.
Taiga Concept recommend to use authorized
installation persons and will not take
responsibility for any harm to persons or
goods due to irresponsible actions.
Product may have some smell after assembling
but it will disappear in few weeks.
Before installation find out your country fire
regulation and contact your local Taiga dealer.
Do not carry out your own modifications to the
product, as it will automatically end warranty.
Check building / floor weight capacity before
assembling the products.
Maintenance
After assembling the product, wipe all surfaces
with clean damp cloth. Avoid using too much
water, as it will damage the product. Prolonged
direct sunlight may change the color of
wooden surfaces over time.
Check tightness of hinges and door position
every six month.
Choosing location
Always place the product inside the building.
Room temperature needs to be minimum 10°C.
Do not place the product to space that is wet
or where has high humidity.
Place the product so that the minimum space
between roof element and ceiling needs to be
at least 10 cm. Building ceiling height minimum
of 230 cm.
When placing the product make sure the door
will not block any walkway and that it does not
damage when open.
Maximum floor deflection ≤ 0,7° degree /
meter.
Warranty / Contact
Safety Equipment
Upon successful installation please inform the
local Taiga dealer to activate the warranty.
It is recommended to use Taiga Concept local
dealers authorized assembling person.
If you have any questions or problems
during installation, please contact your local
Taiga dealer or Taiga Concept’s installation
manager.
[phone]
warranty@taigaconcept.fi
Warranty is not valid if assembly has been
carried out in contradiction to the installa-
tion guide or if it’s done by a person or a
team that has not been authorized by Taiga
Concept or Taiga Concept local dealers.
Always use suitable safety equipment when
installing Taiga Concept products including
safety glasses, shoes, helmet and gloves.
4

1x CW010
1x CF004
1x CR004
1x CR005
1x CG003
2x CG004
3x CG005
2x CA2xx
1x SCA003
Width
700mm
Width 767 mm
1x CF005
1x SR005
1x CW007
1x CW008
1x CW009
Wall
Roof
GlassAcoustic panel & carpet
Floor
Elements &
Components
1x CD004
1x CD005
2x CD006
2x SR006
1x SR007
1x EP106
Length 2135 mm
Length 2335 mm
Frames & Joints
Cables & control panel
1x EC1xx
100cm
1x EP109
5
500cm

4x SS002
4x SS003
2x SS004
2x SS005
8x SF002
3x SM001
4x SC006 2x SR001
12x SC001 16x SC002
Doorframe &
acoustic panel
Wall connector
plate Hinges
Roof
Roof
2x SF006
38x SR003
8x SC003 4x SC005
1x SF001
1x SF003
Length 2100 mm
Length 700 mm
Length 2280 mm
3,5 X 20
4,5 X 30
4,5 X 30
Seals
Screws & Accessories
1x SH00x
Elements &
Components Equipments
& tools
Screw machine+ bits
GlovesSafety glassesSafety shoesSafety helmet
Carpet knifeCleaning toolsProtection material
for elements and glasses
Glass suction cup
min weight capacity 50 kg /pcs
2 x
+
Hex key set
Step ladder Rubber hammer
Spirit or laser level
Wrenches Carpet tape
6,3 x 80
6
6x SC004

ATTENTION
Never put glass against hard surface, use always carton or carpet under the glass.
Use always 2 person and suction cups to lift glass
X
7

SR005
CF004
CF005
SR003
6X
Note: If LB TABLE is installed, SR005 is not needed
Make sure the floor elements are in the final position
Do not slide the product over the room floor
8

SC006
4X
NOTE: Do not continue before floor is level
Hex key 4mm
9

SR003
16X
10

CW010
x2
Keep the wall upright until the glass element is added.
11

CG005
SS002
x2
Add seal 2/3 of the length
Never put glass againsta hard surface, always use carton or carpet under the glass. Always use 2 persons and the suction cups to lift glass
If back glass is close to a wall,
clean it before placing
12

CW009
x2
Keep the wall upright until
the glass element is added.
13

SS002
CG005
x2
Never put glass againsta hard surface, always use carton or carpet under the glass. Always use 2 persons and the suction cups to lift glass
If back glass is close to a wall,
clean it before placing
Add seal 2/3 of the length
14

SR006
15

CW007
x2
Cable for table is routed through
the groove inside the booth
If power is supplied from floor level,
connect supply cable (EC1xx) to the connector
inside the wall before installing the wall
In case power is supplied from
the ceiling, check page52
16

SR006
17

CW008
x2
18

SF006
SC003
2X
SR003
16X
Warning: Do not apply excessive force
Make sure the walls lines
perfectly on top and that
there is no gap bottom of the
wall and oor joint
19

CR005
x2
X
Do not scratch the element surfaces
and be careful with sharp edges
20