Taili 813B User manual

MODEL 813B
FOR YOUR SAFETY:
READ ALL INSTRUCTIONS CAREFULLY

Table of Contents
General safety instructions for Power Tools
…………………………………………
1
Main specification
…………………………………………………………………………
2
Unpacking and checking contents…………………………………………………… 2
List of loose parts in the box and bags………………………………………………. 3
Getting to know your drill press………………………………………………………
..
4
Assembly………………………………………………………………………………….. 5
Lubrication………………………………………………………………………………… 6
Maintenance……………………………………………………………………………… 6
Wire diagram……………………………………………………………………………… 7
Trouble shooting…………………………………………………………………………. 8
Repair parts……………………………………………………………………………….. 9
General safety instructions for Power Tools
1.KNOW YOUR POWER TOOL
Read and understand the ower's manual and labels affixed to the tool.Learn its application and
limitations as well as the specific potential hazards peculiar to this tool.
2.GROUND ALL TOOLS
This tool is equipped with an approved 3 conductor and a 3 prong grounding type plug to fit the
proper grounding type receptacle.
3.KEEP GUARDS IN PLACE
In working order and in proper adjustment and alignment.
4.WEAR PROPER APPAREL
Do not wear loose clothing,gloves,neckties,or jewelry (rings,wrist,watches) to get caught in moving
parts.Wear protective hair covering to contain long hair.Roll long sleeves above the elbow.
5.USE SAFETY GOGGLES
6.KEEP WORK AREA CLEAN
Cluttered areas and benches invite accidents.Floor must not be slippery due to wax or sawdust.
7.KEEP CHILDREN AWAY
-1-

Main Specification
Drill Capacity 16mm / 5/8 in.
Chuck Capacity 13mm / 33/64 in.
Sewing 200mm / 8 in.
Spindle Taper JT33
Distance,Spindle to column 102mm / 4-1/64 in.
Max.Spindle travel 50mm / 1-31/32 in.
Max.distance chuck to table 165mm / 6-1/2 in.
Max.distance chuck to base 245mm / 9-41/64 in.
Motor 120V, Single Phase,60Hz, 300W/ 2/5 HP
Base Size 280 × 180mm / 11-1/32 × 7-3/32 in.
Table Size 165 × 165mm / 6-1/2 × 6-1/2 in.
Overall Height 580mm / 22-53/64 in.
Range of spindle speeds
5 speeds
Motor Speed Spindle Speeds (min-1)
60Hz 1700 min-1 620 1100 1720 2340 3100
Overall dimensions(L × M × H): 470 × 240 × 350mm / 18-1/2 × 9-29/64 × 13-25/32 in
Net Weight 17KGS / 37.5 lbs
Unpacking and checking contents
1.Unpacking and checking contents
Separate all the parts from packaging materials and check each item make sure all items are accounted
for before discarding any packing material.
Item Description Qty
A Table (square or Round )……………………… . 1
B Column Support Asm…………………………… . 1
C Owner's Manual…………………………………… 1
D Box of Loose Parts……………………………… .. 1
E Bag of Loose Parts……………………………… .. *
F Base………………………………………………… . 1
G Head Asm………..………………………………… 1
2.Remove the protective oil that is applied to the table and column.Use any ordinary household
type grease and spot remover
3.Apply a coat of paste wax to the table and column to prevent rust.Wipe all parts thoroughly with
clean dry cloth.
-2-

Main Specification
Unpacking and checking contents
-2-

List of Loose Parts in the box and bags
-3-

Getting To Know Your Drill Press
- 4-

Assembly
Refer to the figure install all parts correctly,
tighten the screw and bolts securelly.
1 Table Support
2. Support Lock handle
3 Column
4 Base
5 Support Column
6 Screw Hex Hd M8x20
7 Table Bevel Lock Screw
8 Table
9 Head Asm
-5-
- 5-

- 5-

Lubrication
All of the BALL BEARING are packed with grease at the factory.They require no further lubrication.
Periodically lubricate the table elevation machanism,the SPLINES (grooves) in the spindle,and the
RACK (teeth of the quill),see "Getting to know your drill press."
Maintenance
Frequently blow out any dust that may accumulate inside the motor.
A coat of automotive type paste was applied to the table and column will help to keep the surfaces clean.
Wire diagram
- 6-

Trouble Shooting
TROUBLE PROBABALE CAUSE REMEDY
Noisy Operation
1.Incorrect belt tension. 1. Adjust tension.
2.Dry Spindle. 2. Lubricate spindle.
3.Loose spindle pulley 3. Checking tightness of retaining nut on
pulley,and tighten if necessary.
4.Loose motor pulley 4.Tighten setscrews in pulleys.
Drill bit burns
1.Incorrect speed. 1. Change speed.
2.Chips not coming out of hole. 2. Retract drill bit frequently to clear chips.
3.Dull drill bit 3. Resharpen drill bit.
4.Feeding too slow 4. Faster the speed.
5.Not lubricated 5. Lubricate drill bit.
Drill bit leads off…
hole not round
1.Hard grain in wood or
lengths of cutting lips
and/or angles not equal
1.Resharpen drill bit correctly.
2.Bent drill bit 2.Replace drill bit.
Wood splinters on
underside
1.No "back up material" 1.Use "back-up material"
under workpiece.
Workpiece turn
loose from hand
1.Not supported or 1.Support working or clamp it.
clamped properly.
Drill bit binds in
workpiece
1.Workpiece pinching drill bit 1.Support working or clamp it.
or excessive feed pressure.
2.Improper belt tension. 2.Adjust temsion.
Excessive drill bit
runout or wobble
1.Bent drill bit 1.Use a straight drill bit.
2.Worn spindle bearings. 2.Replace bearings.
3.Drill but not properly 3.Install drill bit properly.
installed in chuck
4.chuck not properly installed. 4.Install chuck properly.
Quill Returns too
slow or too fast 1.Spring has improper tension. 1.Adjust spring tension.
Chuck will not stay
atached to spindle
if falls off when
trying to install it.
1.Dirty,grease,or oil on the 1.Using a household detergent clean the
tapered inside surface of chuck tapered surface of the chuck and spindle to
or on the spindles tapered remove all dirt,grease and oil.
surface.

-7-

Repair Parts
FIGURE1
Key
No. Description Key No. Description
1 Bushing-Ruber 8 Bearing-Ball 17mm
2 Knob 9 Spacer
3 Screw-Pan Hd.M5x0.8-1.2 10 Insert-Pulley
4 Belt-"V"5/16x26 11 Pulley-Spindle
5 Guard w/Labels 12 Nut-Pulley
6 Screw-Washer Hd. 13 Clamp-Cord
M6x1.0-1.6 14 Screw-Pan Hd.M5x0.8-16
7 Ring Retaining 15 Washer,Foam
-8-

Repair Parts
FIGURE2
-9-

FIGURE2
Key
No. Description Key No. Description
1 Head w/Roll Pin & Trim 19 Box-Switch w/Depth Scale
2 Nut-Lock M8x1.25-8 20 Screw-Pan Cr. M5x0.8-12
3 Washer 21 Switch-Locking
4 Screw-Hex M8x1.25-25 22 Screw-Selt Tapping Pan
5 Pulley-Motor Hd.N4x16-8
6 Screw-Hex Soc.Set M6x1.0-10 23 Cover-Switch Plate
7 Motor 24 Key-Switch
8 Stop-Motor 25 Connector-Wire
9 Spring-Motor Stop 26 Seat-Spring
10 Knob-Motor Adjustig 27 Retainer-Spring
11 Screw-Hex Soc.Set M8x1.25-8 28 Spring-Tension
12 Knob 29 Cap-Spring
13 Rod 30 Nut-Hex 3/8-24
14 Shaft-Pinion 31 Nut-Hex M10x1.5
15 Nut-Hex M8x1.25 32 Pointer
16 Screw-Fit Sit.Set M8x1.25 33 Cord-Power
17 Lockwasher-Ext.1.5mm
18 Screw-Pan hd.M5x0.8-8
-10-

Repair Parts
FIGURE3 FIGURE4
Key No. Description Key No. Description
1 Gasket-Quill 1 Support-Table w/Scale
2 Bearing-Ball 12mm 2 Support-Lock Handle
3 Tube-Quill 3 Tube/Support
4 Screw-Pan M5x0.8-20 4 Base
5 Collar-Stop 5 Screw-Hex Hd.M8x1.25-20
6 Ring-Retaining 6 Screw-Hex Hd.1/2-12x7/8
7 Shaft-Pinion 7 Table
8 Chuck
9 Key-Chuck
10 Nut-Hex M6x1.0
11 Nut-Hex M5x0.8
12 Rod-Stop

FIGURE4 PARTS LIST
Key
No. Description Key No. Description
1 knob-Motor Adjusting 23 Seat-Spring
2 Screw-Socket Set M10*1.5-12 24 Retainer-Spring
3 Handle-Belt Tension 25 Spring-Torsion
4 Pin-Stop 26 Cap-Spring
5 Ring-Depth Stop W/Scale 27 Nut-Hex M12*1.5-8
6 Lock-Depth Screw 28 Head w/Pointer and Trim
7 Hub 32 Tie-Wire
8 Guide Scale 33 Cord-Power w/Plug
9 Knob 36 Clamp-Cord
10 Rod 37 Support-Motor Bracket
11 Lock-Washer-Ext M5 38 Screw-Hex HD M6*1.0*12
12 Screw-Pan HD M5*0.8-8 39 Washer 8*16*1.6
13 Box Switch 40 Mount-Motor
14 Screw-Pan HD M5*0.8-16 41 Cord-Motor
15 Switch-Locking 42 Nut-Hex M8*1.25
16 Screw-Pan HD M4.2*1.4-8 43 Motor
18 Key-Switch 44 Nut-Hex M12*1.75
19 Cover-Switch Plate 45 Lockwasher 1/2
20 Lead-Asm 3 46 Support-Motor Bracket
21 Screw-Set Special 10*1.5-27 47 Screw-Hex HD M8*1.25-16
22 Nut-Hex M10*1.5 48 Lever-Adjusting
-13-