Tandberg Data STORAGE LIBRARY T40 User manual

2
Quick Installation Steps
For more informati on and complete step - by - step instructions, see
Tandberg StorageLibrary
TM
T40 Installation and User Guide .
Caution
The Tandberg StorageLibrary
TM
T40 could be lifted by
one person if drives, power supply, and magazines are
removed. However, for absolute s afety, it is
recommended that two people lift the Tandberg
StorageLibrary
TM
T40. Full library weight = 38 kg / 84 lbs
(2 FH drives). Empty library weight = 23.6 kg / 52 lbs
(does not include drives, magazines or power supply).
Caution
The transport lock ing screws must be removed before
the Tandberg StorageLibrary
TM
T40 can operate
normally.
When following the steps below , see corresponding numbers on the
illustrations.
1 If the library is a rack mount version , power on the unit to remove
the locking scre ws and install the rack mount ears . Install the
library in a rack. If the library is a tabletop version, keep the
locking screws mounted and install the tabletop kit. For
instructions, see Tandberg StorageLibrary
TM
T40 Installation and
User Guide .
2 If your library includes SCSI tape drives c onnect the SCSI cables
to the connectors on the drive sled. See the Installation and User
Guide for installation requirements when using more than 2 SCSI
drives.
a. C onnect a jumper cable between the top SCSI connector of
t he bottom drive and the bottom SCSI connector of the drive
above it. Repeat this step for all drives on the SCSI bus.
Secure the cable with the thumbscrews on the connectors.
b. Terminate the last device on the SCSI bus with the
appropriate SCSI terminator.
c. C onnect a cable between the first drive on the SCSI bus and
the host. Note that there are limitations to the length of the
SCSI cable. In a typical installation, the cable length should
not exceed 9 meters / 30 feet.

3
3 If your library includes fibre channe l tape drives c onnect the fibre
cables to the tape drives :
a. Attach one end of the fibre cable to the fibre port on each
drive. Attach the other end of the cable to the host, switch or
hub .
4 Connect your Ethernet cable to the Ethernet port on the rear of
th e library. The Ethernet connection allows use of the Web
Client .
5 Con nect a power cord to the power connector on the rear of the
library. US and EU power cords are supplied with the library.
6 Power on the library by t urn ing on the rear power switch.
7 If the l ibrary is a tabletop version, the library detects that the
locking screws are present. Follow the instructions on the front
panel display to remove the magazines to get access to the
screws. Remove the screws and reinsert the magazines. The
library will no w continue its power - on sequence.
8 Power up the host syst em.
9 Verify that each host can communica te with the library’s tape
drives.
10 Configure your library using th e library’s operator panel.

4
Table: Power Requirements
Power Requirements Values
Input Voltag e 100 – 240 VAC
Input Frequency 50 –- 60 Hz
Inrush Current (Cold Start)
Less than 15 A, 115 VAC
Less than 30 A, 230 VAC
Power Consumption Average 70 W
Power Consumption Peak* 120 W*
* Maximum peak length, less than 10ms.

5
International H eadquarter
T andb erg Data ASA, Kjelsåsveien 161
P.O. Box 134 Kjelsås, N - 0411 Oslo, Norway
Tel: [phone] , Fax: [phone]
www.tandberg.com
Worldwide subsidiaries
Tandberg Data Corp., 12860 Danielson Court, Poway , U. S.A.
Tel: 858 - 726 - 1800. Fax: 858 - 726 - 1801
Tandberg Data GmbH, Feldstrasse 81, D - 44141 Dortmund, Germany.
Tel: [phone]. Fax: [phone]
Tandberg Data S.A.S., 16/18 Ave. Morane - Saulnier, F - 78941 Vélizy Cedex, France.
Tel: [phone] 00 - 82632374.
Fax: [phone] (for tec hnical support: 00800 - 07867243)
Tandberg Data (Asia) Pte. Ltd, 20 Bendemeer Road, #04 - 05 Cyberhub, Singapore
339914, Tel: [phone]. Fax: [phone]
Tandberg Data (Japan) Inc., Eitaibashi Eco - Piazza Bldg . 8th floor 29 - 13, Shinkawa 1 -
chome, Chuo - ku Tokyo 104 - 033, Japan
Tel: [phone]. Fax: [phone]
Tandberg Data Ltd., Bloxham Mill Business Centre, Barford Road, Bloxham, Banbury,
Oxfordshire, OX15 4FF, United Kingdom
Tel: [phone].
Specifications subject to change without notice. All trademarks are the property of
their respective owners.
©2006 Tandberg Data ASA. All Rights reserved.
Part No. 433559 - 01, June 2006