T&S B-1460-SMB User manual

098-020941-45
03-15-22
TED
JRM 03-24-22
JHB 03-25-22
P/N:
DATE:
DRAWN:
CHECKED:
APPROVED:
Limited One Year Warranty
(Commercial Applications)
T&S warrants to the original purchaser (other than for purposes of resale) that such product is free
from defects in material and workmanship for a period of one (1) year from the date of purchase.
During this one-year warranty period, if the product is found to be defective, T&S shall, at its option,
repair and/or replace it. To obtain warranty service, products must be returned to.....
T&S Brass and Bronze Works, Inc.
Attn: Warranty Repair Department
2 Saddleback Cove
Travelers Rest, SC 29690
Shipping, freight, insurance, and other transportation charges of the product to T&S and the return
of repaired or replaced product to the purchaser are the responsibility of the purchaser. Repair and/
or replacement shall be made within a reasonable time after receipt by T&S of the returned product.
This warranty does not cover items which have received secondary finishing or have been altered
or modified after purchase, or for defects caused by physical abuse to or misuse of the product, or
shipment of the products.
Any express warranty not provided herein, and any remedy for Breach of Contract which might
arise, is hereby excluded and disclaimed. Any implied warranties of merchantability or fitness for a
particular purpose are limited to one year in duration. Under no circumstance shall T&S be liable for
loss of use or any special consequential cost, expenses or damages.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or
limitation of incidental or consequential damages, so the above limitations or exclusions may not
apply to you. Specific rights under this warranty and other rights vary from state to state.
Attention California Residents:
WARNING This product can expose you to chemicals including Lead, Chromium
(hexavalent compounds) and Phthalates (DEHP) which are known to the State of California
to cause cancer and birth defects or other reproductive harm.
For more information go to
www.P65Warnings.ca.gov.
Installation and
Maintenance
Instructions
B-1460-RMB
B-1460-SMB HOSE REEL
CABINET SERIES
EasyInstall Hose Reel Cabinet Series
Recessed Mount Cabinet Assembly
1 SS Hose Reel System Cabinet Flange Recessed Mount 020828-45
2 SS Flange Screws, 10-32 x 3/16 (qty 10) 020840-45
Surface Mount Cabinet Assembly
3 Lock Washer 014200-45
4 O-Ring 001065-45
5 EasyInstall Kit: Nut, Bushing, O-Ring & Lock Washer EZ-K
6 3/8” NPT x 18” Riser 000369-40
7 6” Wall Bracket B-0109-01
8 Hex Bushing, 1/2”NPT Male x 3/8” NPT Female 001359-40
9 Vacuum Breaker 1/2” NPT Female B-0963
10 Check Valve with 1/2” NPT Adapter 015073-40
11 Hose Reel Connector Kit 0RK-SK
12 3/8” NPT x 36” Flexible Connector Hose HW-2B-36
13 3/8” NPT Quick Disconnect AW-5B
14 3/8” NPT Close Nipple 002535-25
15 Quarter-Turn Eterna w/ Spring Check, RTC (new style) 012443-40NS
Quarter-Turn Cerama w/ Check Valve, RTC (new style) 012394-25NS
16 4-Arm Handle (new style) 002521-45NS
17 Lab Handle Screw 000925-45
18 Escutcheon 020839-40
19 Escutcheon, Set Screw 000939-45
20 Red Button Index, Press In 001193-19NS
21 White Blank Button Index 001205-19NS
22 Blue Button Index, Press In 018506-19NS
23 Snap-In Plug, Nickel Plated (qty 10) 020843-45

STEP A:
1. Remove indexes, screws, and handles from cabinet.
2. Remove slip flanges by loosening the set screw (do not
remove from flange).
3. Un-tape VR Bit from top of cabinet and unscrew the (6)
door screws and remove door.
VR BIT
FOR RECESSED MOUNT MODELS:
1. Complete rough-in so mixing valve will be 56” from floor.
2. Punchout oval side wall tabs (2 per side).
3. Use the side oval holes and screw cabinet into appropriate
supports with appropriate fasteners.
4. Finish assembly of 0RK-SK & hose reel.
5. Connect inlet supplies and check for leaks.
6. Reverse STEP A to re-assemble.
ENLARGED VIEW
FOR SURFACE MOUNT MODELS:
1. Place cabinet so mixing valve is 56” from floor.
2. Using 6 of the 8 holes, use appropriate fasteners &
washers to mount to wall. Two of the middle set of
holes will be blocked depending on bottom or top inlet
supplies.
3. Finish assembly of 0RK-SK & hose reel.
4. Connect inlet supplies and check for leaks.
5. Reverse STEP A. to re-assemble.
BACK
FRONT
HOLES
HOLES
(hidden)