manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Taoglas
  6. •
  7. Antenna
  8. •
  9. Taoglas TGX.04 Series User manual

Taoglas TGX.04 Series User manual

Following these guidelines will help ensure that your Taoglas
TGX.04 antenna is installed correctly. The TGX.04 can be mounted
via 3 dierent variations; wall mount, pole mount and suction
cup mount. All mounting methods are outlined below.
TGX.04 Series
MIMO 5G/4G Antenna
Installation Instructions
Introduction
Installation Requirements
IG-21-8-020-A
Pole Mount
• 7mm [9/32”] socket wrench/ screwdriver
• Metal mounting clamp (x2)
• Pole diameter range: 22mm [0.9”] -
50mm [2”]
Wall Mount
• Screwdriver
• Drill
• M4 [Gauge 8] screw (x4)
• M4 [Gauge 8] washer (x4)
• 6mm [1/4”] wall mount stud (x4)
Suction Cups
• D40 suction cups (x4)
Antenna Components: Mounting Plate (x1), Tightening Nut (x1), Antenna Housing (x1), Coaxial Cable(x4)
taoglas.com
All copyrights, trademarks and any other intellectual property rights related are owned by Taoglas Group Holdings Limited.
Caution
To comply with FCC RF Exposure requirements in section 1.1310 of the FCC Rules, antennas used with this device must be installed
to provide a separation distance of at least 20 cm from all persons to satisfy RF exposure compliance.
Warning
Do not Operate the transmitter when someone is within 20 cm of the antenna.
Do not operate the equipment in an explosive atmosphere.
European Waste Electronic Equipment Directive 2002/96/EC
Please ensure that your old Waste Electricals and Electronics are recycled do not throw them away into standard waste.
Notices
Suctions Cups
This antenna should be mounting with suction cups for indoor use only.
Directive (RoHS) 2011/65/EU / 2015/863/EU
Harmonised Standards and References:
EN 301 489-1 (V2.2.1): ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical
requirements. Referencing CENELEC EN 55032 Class B.
IG-21-8-020-A
Pole Mount Installation
Loop the mouting straps around the pole at the desired
position and tighten the strap until the mounting plate
is xed. Use the self centering feature to guide the
mounting plate onto the pole
Insert the metal mounting clamps(both top and bottom)
through the inner slots of the mounting plate
Insert the ball joint rmly into the socket on the back of
the antenna body and slide the tightening nut into the
antenna housing’s back plate to secure in place. Adjust
to the desired antenna orientation on the bal joint and
tighten the nut to x the antenna in place.
Insert the tightening nut onto the ball joint mount with
the at surface facing away from the mounting plate
Installation Completed
Optional: Route cables through the cable guide on the
mounting plate
taoglas.com
IG-21-8-020-A
Wall Mount Installation
Using the mounting plate as a guide mark the position
of the screws to the desired location. Drill holes for wall
mount studs(6mm[1/4”] diamter, min 25mm[1”] depth)
and secure the studs in place. Position the washers into
the mounting plate, insert the screws through and into
the wall studs. Drive the screws in and tighten to secure
the mounting plate in place
Insert the tightening nut onto the ball joint mount from
the mounting plate
Insert the ball joint rmly into the socket on the back of
the antenna bodyand slide the tightening nut into the
antenna housing’s back plate to secure in place. Adjust
to the desired antenna orientation on the ball joint and
tighten the nut to x the antenna in place
Installation Completed
Correct Screw and Washer Location
taoglas.com
IG-21-8-020-A taoglas.com
Suction Cup Mount Installation
Using the mounting plate as guide on the mounting
surface, align to the desired location of the antenna.
Press rmly on each cup to secure in place
Note: Check that the surface to mount on is at,
non-porous, and has been adequately cleaned to ensure
proper adhesion.
Insert the rubber (both top and bottom) through the
inner slots of the mounting plate
Insert the ball joint rmly into the socket on the back of
the antenna body and slide the tightening nut into the
antenna housing’s back plate to secure in place. Adjust
to the desired antenna orientation on the bal joint and
tighten the nut to x the antenna in place.
Insert the tightening nut onto the ball joint mount with
the at surface facing away from the mounting plate
Installation Completed
Waiver: This document represents information compiled by Taoglas to the best of our current knowledge. This is not intended to be used as a
representation or warranty of fitness of the products described for any particular purpose. This document details guidelines for general information
purposes only. When planning installations, always seek specialist advice and ensure that the products are always installed by a properly qualified
installer in accordance with applicable regional laws and regulations.

Other Taoglas Antenna manuals

Taoglas TGX45 Series User manual

Taoglas

Taoglas TGX45 Series User manual

Taoglas iDAS.C.001 User manual

Taoglas

Taoglas iDAS.C.001 User manual

Taoglas MA114 Series User manual

Taoglas

Taoglas MA114 Series User manual

Taoglas PA.11 User manual

Taoglas

Taoglas PA.11 User manual

Taoglas ZRM500 User manual

Taoglas

Taoglas ZRM500 User manual

Popular Antenna manuals by other brands

Trig Avionics TA17 installation guide

Trig Avionics

Trig Avionics TA17 installation guide

Poynting MIMO-4 user guide

Poynting

Poynting MIMO-4 user guide

AirLive WAI-090 installation guide

AirLive

AirLive WAI-090 installation guide

1 BY ONE OUS00-0186 instruction manual

1 BY ONE

1 BY ONE OUS00-0186 instruction manual

Silvercrest 79829 operating instructions

Silvercrest

Silvercrest 79829 operating instructions

Silvercrest SZA 28 A1 operating instructions

Silvercrest

Silvercrest SZA 28 A1 operating instructions

Redline Virtual Fiber RAS-Extend LV Installation guidelines

Redline

Redline Virtual Fiber RAS-Extend LV Installation guidelines

One Forall SV9357 Quick installation guide

One Forall

One Forall SV9357 Quick installation guide

Dream Catcher ME1310 quick start guide

Dream Catcher

Dream Catcher ME1310 quick start guide

Blue Star RC-2EL Instructions and user guide

Blue Star

Blue Star RC-2EL Instructions and user guide

One Forall SV-9153 instruction manual

One Forall

One Forall SV-9153 instruction manual

Intellian i9 Install and user manual

Intellian

Intellian i9 Install and user manual

Procom GF 401 Series quick start guide

Procom

Procom GF 401 Series quick start guide

dB Technologies DA-RS16 quick start guide

dB Technologies

dB Technologies DA-RS16 quick start guide

COMBA COMFLEX Series user manual

COMBA

COMBA COMFLEX Series user manual

DX Engineering DXE-VGMT-3CG manual

DX Engineering

DX Engineering DXE-VGMT-3CG manual

DX Engineering SkyHawk 3X10 instructions

DX Engineering

DX Engineering SkyHawk 3X10 instructions

DX Engineering Hummelmasten Mini XL Step by step manual guide

DX Engineering

DX Engineering Hummelmasten Mini XL Step by step manual guide

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.