Taoglas TGX45 Series User manual

Following these guidelines will help ensure that your Taoglas
TGX45 antenna is installed correctly. The TGX45 can be
mounted via in 3 dierent variations;wall mount, pole mount
and suction cup mount. All mounting methods are outlined
below.
TGX45 Series
MIMO 5G/4G Antenna
Installation Instructions
Introduction
Installation Requirements
Antenna Components: Mounting Plate (x1), Tightening Nut (x1), Antenna Housing (x1), Coaxial Cable(x2)
IG-20-08-008-A www.taoglas.com
• Pole Mount:
7mm [9/32”] socket wrench or screwdriver, metal mounting clamp (x2)
Pole Diameter Range: 22mm [0.9”] - 50mm [2”]
Metal Mounting Clamp Max Torque: 4 Nm [35in-lb]
• Wall Mount:
Screwdriver, drill, M4 [Gauge 8] screw (x4), M4 [Gauge 8] washer (x4), 6mm [1/4”] wall mount stud (x4)
• Suction Cup Mount:
D40 Suction cups (x4)
All copyrights, trademarks and any other intellectual property rights related are owned by Taoglas Group Holdings Limited.
Waiver: This document represents information compiled by Taoglas to the best of our current knowledge. This is not intended to be used as a
representation or warranty of tness of the products described for any particular purpose. This document details guidelines for general information
purposes only. When planning installations, always seek specialist advice and ensure that the products are always installed by a properly qualied installer
in accordance with applicable regional laws and regulations.
Caution
To comply with FCC RF Exposure requirements in section 1.1310 of the FCC Rules, antennas used with this device must be installed
to provide a separation distance of at least 20 cm from all persons to satisfy RF exposure compliance.
Warning
Do not Operate the transmitter when someone is within 20 cm of the antenna.
Do not operate the equipment in an explosive atmosphere.
European Waste Electronic Equipment Directive 2002/96/EC
Please ensure that your old Waste Electricals and Electronics are recycled do not throw them away into standard waste.
Notices

IG-20-08-008-A www.taoglas.com
Pole Mount Installation
Loop the mouting straps around the pole at the desired
position and tighten the strap until the mounting plate
is fixed. Use the self centering feature to guide the
mounting plate onto the pole
Insert the metal mounting clamps(both top and bottom)
through the inner slots of the mounting plate
The TGX.45 antenna can be installed with 3 dierent methods: pole mount, wall mount, and suction
cup mount. Please refer to the appropriate section below that best ts your installation needs
Hardware Installation
Insert the ball joint firmly into the socket on the back of
the antenna body and slide the tightening nut into the
antenna housing’s back plate to secure in place. Adjust
to the desired antenna orientation on the bal joint and
tighten the nut to fix the antenna in place.
Insert the tightening nut onto the ball joint mount with
the flat surface facing away from the mounting plate
Completed Installation
Optional: Route cables through the cable guide on the
mounting plate

IG-20-08-008-A www.taoglas.com
Wall Mount Installation
Using the mounting plate as a guide mark the position
of the screws to the desired location. Drill holes for wall
mount studs(6mm[1/4” ] diamter, min 25mm[1” ] depth)
and secure the studs in place. Position the washers into
the mounting plate, insert the screws through and into
the wall studs. Drive the screws in and tighten to secure
the mounting plate in place
The TGX.45 antenna can be installed with 3 dierent methods: pole mount, wall mount, and suction
cup mount. Please refer to the appropriate section below that best ts your installation needs
Hardware Installation
Insert the tightening nut onto the ball joint mount from
the mounting plate
Insert the ball joint firmly into the socket on the back
of the antenna bodyand slide the tightening nut into
the antenna housing’s back plate to secure in place.
Adjust to the desired antenna orientation on the ball
joint and tighten the nut to fix the antenna in place
Completed Installation
Correct Screw and Washer Location

IG-20-08-008-A www.taoglas.com
Suction Cup Mount Installation
Using the mounting plate as guide on the mounting
surface, align to the desired location of the antenna.
Press firmly on each cup to secure in place
Note: Check that the surface to mount on is flat,
non-porous, and has been adequately cleaned to ensure
proper adhesion.
Insert the metal mounting clamps(both top and bottom)
through the inner slots of the mounting plate
The TGX.45 antenna can be installed with 3 dierent methods: pole mount, wall mount, and suction
cup mount. Please refer to the appropriate section below that best ts your installation needs
Hardware Installation
Insert the ball joint firmly into the socket on the back of
the antenna body and slide the tightening nut into the
antenna housing’s back plate to secure in place. Adjust
to the desired antenna orientation on the bal joint and
tighten the nut to fix the antenna in place.
Insert the tightening nut onto the ball joint mount with
the flat surface facing away from the mounting plate
Completed Installation