TaoTronics TT-HE009 User manual

尺寸：160mm*110mm
胶装
封面105g铜版纸过油，内页105g铜版纸

Model: TT-HE009
TaoTronics PTC Fan Heater
User Guide
E-mail:
[email protected]
MANUFACTURER
Manufacturer: Shenzhen NearbyExpress Technology Development
Co.,Ltd.
Address: Floor 7, Building E, Galaxy World Phase II, Shenzhen, China
TT-HE009_V1.1_ENMADE IN CHINA
www.taotronics.com
This product is only suitable for well
insulated spaces or occasional use.
Intertek
3068797
CM

Contents
01 IMPORTANT SAFETY INSTRUCTIONS
06 Package Contents
06 Product Diagram
07 Operations and Functions
12 Replacement of Batteries in
Remote Control
13 Specifications
13 Cleaning and Maintenance
15 Troubleshooting
17 Warranty and Service

01 02
Thanks for choosing TaoTronics PTC Fan Heater. Please read
this User Guide thoroughly before use and retain it for future
reference.
IMPORTANT SAFETY
INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INFORMATION AND
INSTRUCTIONS. KEEP FOR FUTURE REFERENCE.
FOR HOUSEHOLD USE ONLY
When using electrical appliances, basic precautions should always
be followed to reduce the risk of fire, electric shock, and injury to
persons, including the following:
1. Read all instructions before using this heater.
2. Surface of this heater will become hot during use. To avoid burns,
do not touch hot surfaces with bare hands. Use handles when
moving the unit.
3. High temperature. Keep combustible materials, such as furniture,
pillows, bedding, papers, clothes and curtains at least 3 feet (0.9
meters) from the front and top of the radiator and keep them away
from the sides and rear.
4. This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the appliance by
person responsible for their safety.
5. Do not allow to be used as a toy. Close attention is necessary when
used by or near children. Children should be supervised to ensure
that they do not play with the machine or remote control.
6. Always unplug the heater when not in use.
7. Do not operate any heater with a damaged cord or plug or after
the heater malfunctions, has been dropped or damaged in any
manner. Discard heater, or return the heater to an authorized
service facility for examination, electrical or mechanical adjustment
or repair.
8. Do not use outdoors or on wet surfaces.
9. Do not handle any part of the plug or machine with wet hands.
10. Suitable for dry locations ONLY. This heater is not intended for
use in bathrooms, laundry areas and similar indoor locations.
Never place the heater where it may fall into a bathtub or other
water container. Do not use or store where it may get wet or in the
immediate surroundings of a bath, a shower, or a swimming pool.
11. Do not run cord under carpeting. Do not cover cord with throw
rugs, runners or the like. Do not route cord under furniture or
appliances. Arrange cord away from traffic area and where it will
not be tripped over.
12. To disconnect the heater, turn it off first, then remove the plug
from the outlet.
13. Connect to properly grounded outlets only.

03 04
14. Do not insert or allow foreign objects to enter any ventilation or
exhaust opening as this may cause electric shock, fire or damage
to the heater.
15. To prevent a possible fire, do not use with any opening or exhaust
blocked, and keep free of dust, lint, hair, and anything that may
reduce airflow. Do not put any object into the inlet grill or the
exhaust opening as this may cause an electric shock or fire, or
damage the appliance.
16. A heater has hot or arcing or sparking parts inside. Do not use it
in areas where gasoline, paint or flammable liquids are used or
stored.
17. Use this heater only as described in this User Guide. Any other use
not recommended by the manufacturer may cause fire, electric
shock, injury to persons or other damage to property.
18. To prevent overload and blown fuses, be sure that no other
appliance is plugged into the same outlet (receptacle) or into
another outlet (receptacle) wired into the same circuit.
19. If there is a loose fit between the plug and the socket or the plug
becomes very hot, the socket may need to be replaced. Check
with a qualified electrician to replace the socket.
20. It is normal for the plug and cord to feel warm to the touch. A plug
or cord which becomes hot to the touch or becomes distorted in
shape may be a result of a worn electrical outlet. Worn outlets or
receptacles should be replaced prior to further use of the heater.
Plugging heater into a worn outlet / receptacle may result in
overheating of the power cord or fire.
21. The output of this heater may vary and its temperature may
become intense enough to burn exposed skin. Use of this heater
is not recommended for persons with reduced sensitivity to heat
or an inability to react to avoid burns.
22. Ensure the heater is on a stable, secure surface to eliminate the
potential of tipping it over.
23. Always plug heaters directly into a wall outlet / receptacle. Never
use with an extension cord or relocatable power tap (outlet /
power strip).
24. Be sure that the plug is fully inserted into appropriate receptacle.
Please remember that receptacles also deteriorate due to aging
and continuous use: check periodically for signs of overheating or
deformations evidenced by the plug. Do not use the receptacle
and CALL your electrician.
25. Check that neither the appliance nor the power cable has been
damaged in any way during transportation.
26. Make sure that no pieces of polystyrene or other packaging
material have been left between elements of the appliance. It may
be necessary to pass over the appliance with a vacuum cleaner.
27. Do not attempt to modify or repair the product by yourself. Doing
so could void the warranty and cause damage or personal injury.
Only a repair technician may disassemble or repair this product.
28. Choking hazard – This remote control unit contains a small battery.
Keep the remote control away from children and do not swallow
the battery. If the battery is swallowed seek medical advice at
once.
29. If the machine is not working as it should, has received a sharp
blow, has been dropped, damaged, left outdoors, or dropped
into water, do not use and contact the Customer Support.
30. Before cleaning, or storage, or when not in use, always turn the
heater OFF and unplug it from the electrical outlet and allow to
cool.
31. NOTE: There may be a trace of smoke or odor when the unit is
first operated. This indicates that a drop of oil fell on the heating

05 06
coil during the manufacturing process. It will quickly evaporate
and should not re-occur.
32. IMPORTANT - This appliance has a polarized plug (one blade is
wider than the other). To reduce the risk of electric shock, this
plug is intended to fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician. Do not attempt to rig this
safety feature.
DANGER-High temperatures may be generated under certain ab-
normal condition.
Do not partially or fully cover or obstruct the front of this heater.
READ AND SAVE THESE
INSTRUCTIONS
Package Contents
①1x TaoTronics PTC Fan Heater (TT-HE009)
②1x Remote Control
③1x Thank You Card
④1x User Guide
Product Diagram
Handle
Rear Cover
LED Display Control Buttons
Power Cord and Plug
Grille / Air Outlet
Base

07 08
Operations and Functions
Remote Control
Note: For added convenience, the same control buttons can be
found on the remote control.
Power ON/OFF
Oscillation Button
Mode / Heat
Level Button ECO Mode
Temperature -
Temperature +
Timer Button
Operations and Functions
Place the heater on a firm, level surface free from obstructions, and at
least 3ft. (0.9m) away from any wall or combustible material. Plug into
an appropriate voltage AC outlet, the unit will enter standby mode
with a beep and illuminated. Your heater is ready for use now.
Power ON/OFF
• Press on the heater / remote control once to turn the heater ON
with default settings: temperature “85°F” & high heat level on
LED display.
• If no operation is done in 60 seconds, the LED display will turn off
automatically.
• Press once again to turn the heater OFF (standby mode).
Mode / Heat Level Setting
• When the unit is on, repeatedly press on the heater or on the
remote control to cycle through High ->Low -> ECO -> High modes.
ECO Mode
• When the unit is on, repeatedly press on the heater or on the
remote control to select ECO mode.

09 10
• Or press on the remote control to turn on/off ECO mode directly.
• When ECO mode is turned on, the heater will adjust the working
mode (High or Low) automatically based on the ambient
temperature.
• Default temperature: 75°F.
• Temperature Adjustment
• When the unit is on, repeatedly press on the heater or / on
the remote control to cycle through 85°F -> 65°F -> 70°F -> 75°F ->
80°F -> 85°F.
• When the setting temperature is reached, the heater will stop
working. When the room temperature is lower than the set one, the
heater will start working again.
Timer Setting
• Auto Stop Timer: When the unit is ON, repeatedly press on the
heater / remote control to set the number of hours (0~7h) you want
the unit to run before it switches off. When time is up, the unit will
automatically stop running.
• Auto Start Timer: When the unit is OFF (with the heater plugged
into an electrical outlet), press on the heater / remote control to
set the number of hours (0~7h) you want the unit to start running
automatically. When time is up, the unit will automatically start
running.
• To cancel Timer setting, adjust the timer setting to 0 or turn off the
unit.
Oscillation Button
• When the unit is on, press on the heater / remote control to start
oscillating.
• To stop oscillating, press it again.
Auto LED Display OFF
• Press and hold and on the heater simultaneously for 3 seconds
to turn on/off the Auto LED display off mode.
• When the unit is powered on for the first time, the Auto LED display
off mode is turned on by default.
Other Features
Memory Function
• If power is not disconnected, the heater will always remember your last
settings (temperature & working mode) once you turn it on again.

11 12
12-Hour Auto Shut Off
• When the heater has been working for 12 hours continuously
without any other operation, it will shut off automatically.
Tip-Over Protection
• When the heater is tipped over, the heater will shut off automatically
with 10 beeps.
• Place the heater back on a flat, level and stable surface and remain
upright. Then turn it on again.
Overheat Protection
• When the ambient temperature is above 122°F, the heater will
stop heating and the overheat alarm will be triggered with timer
indicators (1h, 2h, 4h) flashing and 10 beeps.
• Please unplug it from the power source and power it on again when
the ambient temperature drops below 122°F.
Temperature sensor open / short circuit
• Open circuit: Timer indicator “1h” flashes on the LED display with 10
beeps.
• Short circuit: Timer indicator “2h” flashes on the LED display with 10
beeps.
• Please unplug it from the power source and contact TaoTronics
Customer Support.
Replacement of Batteries in
Remote Control
1.Remove the battery box cover along the indicated arrow direction.
2.Replace with two new #7 (AAA 1.5V) dry batteries. Make sure
positions for “+” pole and “-” pole are correct.
3.Reinstall the battery box cover.
CAUTION:
• Replace with new batteries of the same type when replacement is
required.
• When not using the remote control for a long time, please take out
the batteries.
• Do not attempt to dismantle the batteries.
• Do not dispose the batteries in fire, batteries may explode or leak.

13 14
Specifications
Model TT-HE009
Input 120V~ 60Hz
Rated Power 1500W
Remote Control Battery AAA 1.5V
Cleaning and Maintenance
It is recommended that the heater be cleaned at least one time during
the operating season and before off-season storage in order to
provide the optimum level of performance.
Always disconnect the appliance from the mains by switching it off
and removing the plug from the power outlet before cleaning.
• Turn the heater “OFF”, unplug it and wait for the heater to cool
down.
• Use only a soft cloth to gently wipe the outer surfaces of the heater
clean.
• Do not use any cleaning agents or detergents.
• Never immerse the heater in water and never allow water to drip
into the motor housing. Be sure not to wet the Heating Element and
the switches.
• For storage, you may leave the heater covered to protect it from
dust. Store it in a cool, dry location and arrange the cable away from
traffic areas so that it will not be tripped over or damaged.
Caution:
• Do not allow water to run into the interior of the heater as this could
result in a fire or electric shock hazard.
• Any other servicing should be performed by an authorized service
representative.

15 16
Troubleshooting
The following troubleshooting guide addresses the most common
problems. If problems persist, contact the Customer Support at
[email protected].
Problem Possible Causes Solution
Heater
does not
start
Power cord is not
properly plugged
in.
Connect the plug to a powered
electrical outlet.
Overheat
Protection has
been activated.
• Turn the heater OFF, unplug it
and allow it to cool.
• Check and remove any
objects on or adjacent to the
heater.
• Wait 5-10 minutes before
plugging the unit back in.
No power is
passing through
the unit.
• Ensure that your circuit
breaker or fuse is working
properly.
• Ensure your heater is placed
on a flat and even surface.
Setting
temperature is
lower than the
room temperature.
Make sure the thermostat is set
at a higher temperature than
the room temperature.
Problem Possible Causes Solution
The
heater
suddenly
stops
during
heating
Ambient
temperature
reaches above
122°F.
Unplug it from the power
source and power it on again
when the ambient temperature
drops below 122°F.
The heater is
tipped over.
Place it on a flat, level and
stable surface and remain
upright. Then turn it on again.

17
Warranty and Service
This product is covered with TaoTronics product and labor warranty
for 12 months from the date of its original purchase. If any problems
occur, please contact the TaoTronics Customer Care Centre via the
contact information listed in this User Guide.
We can only provide after sales service for products that are sold by
TaoTronics or TaoTronics authorized retailers and distributors. If you
have purchased your unit from a different place, please contact your
seller for return and warranty issues.