Teac AG-980 Manual

STANDBY LED AVCC VREF BAND OPTION AVSS SET OPTION NC NC KEY_IN3 KEY_IN2 KEY_IN1 POWER DOWN NC NC NC NC NC NC NC NC
P9_7 AVCC VREF
P10_0
AVSS
P10_1 P10_2 P10_3
P10_4/K10 P10_5/K11 P10_6/K12 P10_7/K13
P0_0/D0 P0_1/D1 P0_2/D2 P0_3/D3 P0_4/D4 P0_5/D5 P0_6/D6 P0_7/D7
VOL_UP P9_6 P1_0/D8 NC
VOL_DN P9_5 P1_1/D9 NC
FL_RST P9_4 P1_2/D10 NC
FL_CS P9_3 P1_3/D11 NC
FL_CLK P9_2 P1_4/D12 NC
REMOCON P9_1 P1_5/D13/INT3 NC
FL_DATA P9_0 P1_6/D14/INT4 RDS_CLK
VSS BYTE P1_7/D15/INT5 NC
CNVSS CNVSS P2_0/A0 NC
NC P8_7 P2_1/A1 NC
NC P8_6 P2_2/A2 NC
RESET RESET P2_3/A3 NC
XOUT XOUT P2_4/A4 NC
VSS VSS P2_5/A5 NC
XIN XIN P2_6/A6 NC
VCC VCC1 P2_7/A7 NC
NMI P8_5 VSS VSS
NC P8_4 P3_0/A8 NC
NC P8_3/INT1 VCC2 VCC2
PROTECTION P8_2/INT0 P3_1/A9 NC
SPK_RLY_A P8_1 P3_2/A10 NC
SPK_RLY_ B P8_0 P3_3/A11 NC
SPK_RLY_ C P7_7 P3_4/A12 NC
SPK_RLY_ D P7_6 P3_5/A13 NC
POWER RLY P7_5 P3_6/A14 NC
H/P_RELAY P7_4 P3_7/A15 NJW1197_CLK
NC P7_3 P4_0/A16 NJW1197_DATA
NC P7_2 P4_1/A17 NJW1197_LATCH
NC P7_1 P4_2/A18 NC
NC P7_0 P4_3/A19 P98 E2PROM_SDA
P6_7 P6_6 P6_5 P6_4 P6_3 P6_2 P6_1 P6_0 P5_7 P5_6 P5_5 P5_4 P5_3 P5_2 P5_1 P5_0 P4_7 P4_6 P4_5 P4_4
TX(Crestron) Rx(Crestron)
NC NC NC NC
TUNED
PLL_DA_IN
PLL_CLK
PLL_DA_OUT
RS232C_UPGRADE(EPM)
PLL_CE
RDS_DATA
NC NC
RS232C_UPGRADE(CE)
TUNER_MUTE
MAIN_MUTE ROOM_MUTE
E2PROM_SCL
IC101
AG980B MICOM CONTROL PIN DEFINE
10 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
52
51
464544434241403938373635333231
30
29
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
34 50494847
84 83 82 81
12MHz
M30302FEPFP
62
61
60
59
58
57
5
55
54
53
19
20
21
22
23
24
25
26
2
28

PIN NO. NAME I/O B'D
1
VOL_UP IInput for main volume up.
2
VOL_DN IInput for main volume down.
3
FL_RST OReset signal output to SC16315
4
FL_CS OChip enable signal output to SC16315
5
FL_CLK OClock signal output to SC16315
6
REMOCON IInput fot the Remocon data
7
FL_DATA OData signal output to SC16315
8
VSS Ground
9
CNVSS Flash memory programing mode setting
10
NC Not used!
11
NC Not used!
12
RESET IInput for resetting the CPU
13
XOUT Output for 12MHz crystal oscillator
14
VSS Ground
15
XIN input for 12MHz crystal oscillator
16
VCC +3.3V power supply
17
NMI CPU internal operating for Port
18
NC Not used!
19
NC Not used!
20
PROTECTION IInput for protect data
21
SPK_RLY_A OOutput for Relay control data
22
SPK_RLY_B OOutput for Relay control data
23
SPK_RLY_C OOutput for Relay control data
24
SPK_RLY_D OOutput for Relay control data
25
POWER RLY OOutput for Relay control data
26
H/P_RELAY OOutput for Relay control data
27
NC ONot used!
28
NC Not used!
29
NC Not used!
30
NC Not used!
31
TX(Crestron) OCPU upgrade data transmit
32
Rx(Crestron) ICPU upgrade data receiver
33
NC Not used!
34
NC Not used!
35
NC Not used!
36
NC Not used!
37
TUNED IInput for detecting "TUNED" condition.
38
PLL_DA_IN IInput for PLL data receiver
39
PLL_CLK OClock signal output to tuner pack
40
PLL_DA_OUT OOutput for PLL data receiver
41
RS232C_UPGRADE(EPM) IFlash memory programing mode setting
42
PLL_CE IChip enable signal output to tuner pack
43
RDS_DATA IRadio data signal input from tuner pack
44
NC
45
NC
46
RS232C_UPGRADE(CE) IChip select for CPU upgrade
47
TUNER_MUTE OData signal output to tuner mute
48
MAIN_MUTE OData signal output to main mute
49
ROOM_MUTE OData signal output to room2 mute
50
E2PROM_SCL OClock signal output for E2PROM
51
E2PROM_SDA I/O Data signal output for E2PROM
52
NC Not used!
53
NJW1197_LATCH OChip select data for NJW1197
54
NJW1197_DATA OCommnuication data for NJW1197
55
NJW1197_CLK OClock signal for NJW1197
56
NC Not used!
57
NC Not used!
58
NC Not used!
59
NC Not used!
60
NC Not used!
61
NC Not used!
62
VCC2 +3.3V Power supply
63
NC Not used!
64
VSS Not used!
65
NC Not used!
66
NC Not used!
67
NC Not used!
MODEL : AG980 M30302FEPFP u-COM PORT Design

PIN NO. NAME B'D
68
NC Not used!
69
NC Not used!
70
NC Not used!
71
NC Not used!
72
NC Not used!
73
NC Not used!
74
RDS_CLK OClock signal for tuner RDS
75
NC Not used!
76
NC Not used!
77
NC Not used!
78
NC Not used!
79
NC Not used!
80
NC Not used!
81
NC Not used!
82
NC Not used!
83
NC Not used!
84
NC Not used!
85
NC Not used!
86
NC Not used!
87
NC Not used!
88
NC Not used!
89
POWER DOWN IInput for power down
90
KEY_IN1 IData input for key scan
91
KEY_IN2 IData input for key scan
92
KEY_IN3 IData input for key scan
93
NC Not used!
94
NC Not used!
95
SET OPTION IInput for select set
96
AVSS Ground
97
BAND OPTION IInput for select the frequency ranges steps of FM and AM
98
VREF +3.3V power supply
99
AVCC +3.3V power supply
100
STANDBY LED OOutput signal for LED

GND
TX
+12V
R-OUT
L-OUT
RX
CE
RDS CLK
PLL DATA IN
PLL DATA OUT
DOM 470K 470K
TUNER_L
CLK
GND
RESET
GND
EPM
FUSE USA
REGION OPTION
USA
EUR
R108R107
470K
470K
DAB B'D
PLL CE
TUNED
AMP B'D
+Vkk FLT 2LINE
+3.9V
CNVSS
-Vkk
MAIN
RLY_A
INPUT
RS232 B'D
FRONT
RDS DATA
MUTE_B+
ROOM
RLY_D
MAIN
RLY_B
ROOM
RLY_C
DAB ONLY
EUROPE
TUNER PACK
TUNER_R
Protection
ڜڢڔړڋٻڨڜڤکٻګڜڭگ

TO MAIN B'D
TO MAIN B'D
TO
MAIN B'D
TO H/P B'D
ڭڮڍڎڍٻګڜڭگ
ڨګٻڪکڧڴ
ڜڢڔړڋٻڜڨګٻګڜڭگ

ڨګٻڪکڧڴ