Team Magic E4RSII User guide

507002
E4 Racing Spec. the Second Generation

Thank you for choosing the Team Magic E4RSII EVO. Before you start building the E4RSII EVO, we
suggest you read though the instruction manual first. Be sure to check all assembly and performance
tips before you start. We hope you enjoy the fine building processes.
General Building Tips:
Read the instruction manual before building.
Clear a work area and try to work on a light color towel to avoid missing dropped parts.
Don't forge the thread lock. Be certain to use thread-lock on all the machine screws that thread into metal. Put it
on the screws that are secured with locknuts and the setscrews that secure the linkage stops, too. Don't skimp on
the thread-lock or you'll be searching in the dirt for screws that vibrated loose.
Don't over-tighten fasteners. Many assembly problems are caused by over-tightening screws or nuts. Don't use too
large a grip. Please go slowly and feel the resistance build. Just snug it up.
As you put more time and runs on the car, the suspension arms, and basically anything else that moves, can stretch
and wear. Though we have a very rigorous quality control program and make every effort to ensure that the parts
have the best possible fit when you get them. Unfortunately there is very little, or nothing we can do to prevent
these parts from wearing out. When the arms begin to wear you will notice that some slop develops between the
carrier or hub and the arms. This slop can be taken out by shimming the arm, hub or carrier. If you take a look at
any of the factory driver's cars you will definitely find that they use shims to take up some of the slop that occurs over
a period of time. The shims can also be used on the inside of the suspension arms in the same manner. When
shimming the parts, care must be taken not to add too many shims. The parts must still move freely without binding.
When it doesn't fit, please double check. If an assembly is not going together correctly, then either there really is a
bad fit (e.g. a part is damaged or defective) or a mistake in assembly. Always re-read the instructions when there
are any problems. If you cannot figure out what's wrong, always ask dealer, distributor or Team Magic. Don't use
force beyond what the instructions call for.
Using the right tools makes assembly much easier. The instructions below finely indicate you what tools to get to
make things easier. We don't want to scare you by saying that all these tools are required, but you will have an
easier time if you have them. Borrow them from a friend to check if necessary.
The assembly is arranged so that you will open the bag and finish that bag before you go on to the next bag.
Sometimes, you will have parts remaining at the end of a bag. These will become part of the following bags.
A Good Dealer Is Extremely Important!!
A good hobby dealer can help you with most assembly problems you might encounter. This is the main reason why
you should buy your kits from a good dealer rather than from the cheapest dealer. Bring your problematic parts to
the dealer and, most likely, you'll walk away soon thereafter with the problem solved. If you think that you really
don't have the mechanical skills to complete the assembly, you may pay your dealer to finish the job for you. We
can recommend good dealers to you if you need. Please send us mails for more information. Email:
[email protected]
01
E4 Racing Spec. the Second Generation

A
B
507104
507108
507103
507102
126306
126306
150510ST
116203
507110
116238
507109
126305BU
507110
116203
150510ST
K6601-110
126306
507201
116226
02
126306
3x6mm Steel FH
Screw
150510ST
5x10x4mm Steel
Bearing
116203
E-clip 5
116238
2x12.8mm Pin
126305BU
M3X5mm BH Screw
116226
3.1X4.8X0.5mm
Washer

C
: Grease lubrication
507206
130129
130129
116228
152005
507207
507208
507114
507115
126308
K6330-500000
507116
151015ST
507209
126312C
507212
507211
507213
507212
126312C
507210
126304BU
151015ST
507116
151015ST
507116
151015ST
507116
K6330-1000
152005
507207
507208
507206
507206
Front Spool Ver.
116228
03
152005
4.7x1.42 O-RING
116234
2x9.0mm Pin
130129
5.2x12x0.2mm Shim
151015ST
10x15x4mm Steel
Bearing
126308
3x8mm Steel Flat
Head Screw
126312C
3X12mm CAP Screw
126304BU
M3X4mm BH Screw

D
E
Front
507204
507119
507215
507214126306BU
507203
507202
126308
507205
507120
126308BU
116216
126306
(Front Diff)
(R)
(Front Spool)
or
04
126306
3x6mm Steel F.H.
Screw
126306BU
3x6mm Steel Button
Head Screw
126308
3x8mm Steel F.H.
Screw
126308BU
3X8mm Button
Head Screw
116216
3X6X1mm Washer

E
E
Lower Diff. Position
Higher Diff. Position
Lower Diff. Position
Higher Diff. Position
TightLoose
TightLoose
Rear
507217
126212BU
126308BU
507216
126306BU
507215
126306BU
126306BU
05
126308BU
3x8mm Steel Button
Head Screw
126212BU
2X12mm BH Screw
126306BU
3x6mm Button
Head Screw

F
F
65.5mm
503117
503139
126306BU
503127
150508ST
150306ST
150508ST
116134GD
126308
507126
507126
06
150508ST
5x8x2.5mm Steel
Bearing
150306ST
3x6x2.5mm Steel
Bearing
503117
5x4mm Ball Stud
126308
3x8mm Steel F.H.
Screw
126306BU
3x8mm Steel Button
Head Screw
503127
5x10mm Ball Stud

G
G
21mm
Roll Center Position
0mm +0.75mm -0.75mm
!
3mm
Front
Front
503123
126408S
126308S
130124
507131
126316BU
507128
130114
507129
130114
503121
507129
507127H
126204BU
507130
07
130114
3X6X1mm Washer
126408S
4x8mm Set Screw
126308S
M3X8mm Set
126204BU
2x4mm Steel Button
Head Screw
126316BU
M3X16mm BH Screw
130124
3x7.5x1.5mm Washer

H
H
Roll Center Position
0mm +0.75mm -0.75mm
Rear
Rear
507218
503117
130114
507129
126408S
503139
507235H
126310S
507133
130114
507129
130124
507131
126316BU
126314BU
08
126408S
4x8mm Set Screw
130114
3X6X1mm Washer
503117
5x4mm Ball Stud
126310S
M3X10mm Set
130124
3x7.5x1.5mm Washer
126316BU
M3X16mm BH Screw
126314BU
3x14mm Button
Head Screw

I
I
Front
Front
(R)
(L)
(R)
(L)
503139
503139
503117
503117
116133GD
116133GD
507138
507138
507137-1
507137-3
126310BU
126310BU
507219
507219
507234-1
507234-4
507234-4
507136
507136
507136
126302S
116240
116240
507137-2 507139
507139
126206C
507140
126206C
507234-5
507234-3
507234-6
507234-2
507140
150510ST
150510ST
507234-7
503127
130114
503127
130114
54mm
54mm
Front Diff. Ver.
Front Spool Ver.
507234
09
130114
3X6X1mm Washer
150510ST
5x10x4mm Steel
Bearing
116240
2x9.8mm Pin
126206C
2x6mm Cap Screw
503127
Steering Block
5x10mm Ball Stud
126310BU
3x10mm Button Head
Screw
126302S
3x2mm Set Screw
507234-7
5x10x3mm Steel
Bearing
503117
5x4mm Ball Stud

I
J
Front
Rear
503117
507137-1
126302S 507137-2
503127
507142
126206C
507140
116219
150510ST
507137-3
503139
116133GD
126303S
53.5mm
507141
116219
111165
116240
507138
10
150510ST
5x10x4mm Steel
Bearing
116240
2x9.8mm Pin
126206C
2x6mm Cap Screw
116219
3x6x2mm Alum.
Washer
503127
Steering Block
5x10mm Ball Stud
126302S
3x2mm Set Screw
126303S
3x3mm Set Screw

J
K
1.4mm
Rear
Front
126303S
507143
116219
126303S
126303S
126308BU
507221
507220
507221
11
126303S
3x3mm Set Screw
126308BU
3x8mm Steel Button
Head Screw
116219
3x6x2mm Alum.
Washer

K
L
1.2mm
Rear
507221
126303S
126303S
126308BU
507222
126308SE
126306BU
126308SE
503226
116132GD
503117
503139
503138
130125
507223
507147 (25T/Futaba/Savox/Orion/Power HD)
507148 (23T/KO/JR/Sanwa/Airtronics)
12
126308SE
3x8mm Steel Flat
Round Servo Mount
Screw
503138
5x7mm Ball Stud
503117
5x4mm Ball Stud
130125
3x6x4mm Alum.
Washer
126306BU
3x6mm Steel Button
Head Screw
126308BU
3x8mm Steel Button
Head Screw
126303S
3x3mm Set Screw

L
M
126306
116219
126306BU 507224
126306BU
13
126306BU
3x6mm Steel Button
Head Screw
126306
3x6mm Steel FH
Screw
116219
3x6x2mm Alum.
Washer

M
N
507225
111007ST
126306
126306BU
126306BU
116242
507152
116227
507227
507226
130111
507228
115033
115034
507116
507231
507229
507233
507233
F:K4901-27
R:K4901-25
152002
507229
507230
507232
K6310-600
14
130111
2.6X6X0.5mm
Washer
116227
E-clip 2.0
126306BU
3x6mm Steel Button
Head Screw
126306
3X6mm Steel F.H.
Screw
111007ST
3mm Steel Locknut

N
N
N
503126
126306BU
15
126306BU
3x6mm Button
Head Screw
503126
3.1X6.5X1mm Alum.
Washer

O
O
507162
126310BU
507164
507163
507162
507164
126308
111007ST
507164
507162
126212BU
126212BU
126310
126308 126306
111145BK
126310
16
126306
3x6mm Steel FH
Screw
126310
3x10mm Steel FH
Screw
111007ST
3mm Steel Locknut
126308
3x8mm Steel F.H.
Screw
126212BU
2X12mm BH Screw
126310BU
3x10mm Button
Head Screw

O
O
111160BK
111160BK
126306BU
17
11046BK
4mm Alum. Flanged
Lock Nut (Thin)
(4) Black
126306BU
3x6mm Steel Button
Head Screw

Stiff Setting
P
Motor Position
Setting
P
130114
130114
126312BU
507151
130114
126306BU
130114
126306
126306
130114
18
126306BU
3x6mm Steel Button
Head Screw
130114
3X6X1mm Washer

STIFF SETTING
Spur 1.9
Pinion
DRIVE RATIO
TIRES
ESC Timing Turbo Timing
ESC
E4 Racing Spec. the Second Generation
wt
Spool
wt
Diff.
High
Low
Diff.
High
Low
Spool
186 189 1000500000
1.4
1
1.5
1.5
2
0
1
110
1
+1
4
5
6
-2
-3
-1.5
5.5
5
4
2 0
1.5
1
1.1 mm 1.1 mm
33
600 600
k-factory 27 k-factory 25
2
1.2