Tech Controllers EU-L-7E User manual

1
Users manual
EU-L-7e

2
TABLE OF CONTENTS
I. Safety............................................................................................................................................................................. 3
II. Device description......................................................................................................................................................... 4
III. Installation..................................................................................................................................................................... 5
IV. First start-up.................................................................................................................................................................. 6
V. Main screen description.............................................................................................................................................. 10
VI. Controller functions .................................................................................................................................................... 12
1. Block diagram –contoller menu ............................................................................................................................... 12
2. Screen view ............................................................................................................................................................... 13
3. Manual mode ............................................................................................................................................................ 13
4. Zones ......................................................................................................................................................................... 13
5. Voltage-free contact.................................................................................................................................................. 13
6. Language selection....................................................................................................................................................13
7. Display contrast......................................................................................................................................................... 13
8. Fitter’s menu ............................................................................................................................................................. 13
9. Software version ....................................................................................................................................................... 13
VII. Zones........................................................................................................................................................................... 14
10. Block diagram –zones menu ................................................................................................................................ 14
11. OFF/ON ................................................................................................................................................................. 14
12. Pre-set temperature ............................................................................................................................................. 14
13. Weekly control...................................................................................................................................................... 14
14. Operation mode.................................................................................................................................................... 15
15. Calibration............................................................................................................................................................. 15
16. Hysteresis.............................................................................................................................................................. 15
VIII. Fitter’s menu ...............................................................................................................................................................15
17. Block diagram –fitter’s menu............................................................................................................................... 15
18. Valve...................................................................................................................................................................... 17
19. Internet module.................................................................................................................................................... 18
20. TECH regulator ...................................................................................................................................................... 18
21. Clock...................................................................................................................................................................... 18
22. Set date................................................................................................................................................................. 18
IX. Own schedule settings ................................................................................................................................................ 19
X. Protections and alarms ............................................................................................................................................... 21
XI. Software update.......................................................................................................................................................... 21
KN.18.01.15

3
I. SAFETY
Before using the device for the first time the user should read the following regulations carefully. Not obeying the rules
included in this manual may lead to personal injuries or controller damage. The user’s manual should be stored in a safe
place for further reference. In order to avoid accidents and errors it should be ensured that every person using the device
has familiarized themselves with the principle of operation as well as security functions of the controller. If the device is to
be sold or put in a different place, make sure that the user’s manual is there with the device so that any potential user has
access to essential information about the device.
The manufacturer does not accept responsibility for any injuries or damage resulting from negligence; therefore, users are
obliged to take the necessary safety measures listed in this manual to protect their lives and property.
WARNING
High voltage! Make sure the regulator is disconnected from the mains before performing any activities involving
the power supply (plugging cables, installing the device etc.).
The device should be installed by a qualified electrician.
Before starting the controller, the user shoud measure earthing resistance of the electric motors as well as the
insulation resistance of the cables.
The regulator should not be operated by children.
WARNING
The device may be damaged if struck by a lightning. Make sure the plug is disconnected from the power supply
during storm.
Any use other than specified by the manufacturer is forbidden.
Before and during the heating season, the controller should be checked for condition of its cables. The user should
also check if the controller is properly mounted and clean it if dusty or dirty.
Changes in the merchandise described in the manual may have been introduced subsequent to its completion on January
15th 2018. The manufacturer retains the right to introduce changes to the structure. The illustrations may include additional
equipment. Print technology may result in differences in colours shown.
Care for the natural environment is our priority. Being aware of the fact that we manufacture
electronic devices obligates us to dispose of used elements and electronic equipment in a
manner which is safe for nature. As a result, the company has received a registry number
assigned by the Main Inspector of Environmental Protection. The symbol of a crossed out
rubbish bin on a product means that the product must not be thrown out to ordinary waste
bins. By segregating waste intended for recycling, we help protect the natural environment. It
is the user's responsibility to transfer waste electrical and electronic equipment to the selected
collection point for recycling of waste generated from electronic and electrical equipment.

4
II. DEVICE DESCRIPTION
EU-L-7E external controller is intended for controlling valves. The controller enables significant energy saving due to precise
temperature management in particular rooms. Thanks to advanced software the controller fulfils a wide range of functions:
•possibility of controlling up to 22 thermostatic actuators via 8 room sensors (C-7p):
•one voltage contact for a 230V pump
•voltage-free contact (e.g. for controlling the heating device)
•voltage-free contact for controlling the pump operation algorithm (switching between heating and cooling)
•possibility of connecting ST-507 Internet or WiFi RS to control the system via the Internet
•possibility of connecting M-7 wireless control panel
•possibility of controlling the mixing valve (connecting ST-431N or i-1m valve module is necessary)
•possibility of updating the software via USB

5
III. INSTALLATION
EU-L-7E controller should be installed by a qualified person. The device is intended to be a free-standing unit or a wall-
mountable panel.
WARNING
Risk of fatal electric shock from touching live connections. Before working on the controller switch off the
power supply and prevent it from being accidentally switched on.
NOTE
Incorrect connection of wires may damage the controller.
1. Controller cover (it needs to be removed before connecting the devices to be controlled)
2. Controller display
3. Navigation button
1
2
3

6
NOTE
The device is intended to be mounted on a DIN strip.
IV. FIRST START-UP
In order for the controller to operate correctly, the user must follow these steps when starting the device for the first time:
Step 1. Connect EU-L-7E controller with the devices
Remove the cover and connect the wires following the clues on the connectors and the diagrams presented below.
Follow this order while connecting:
-all the necessary C-7p sensors (connectors 1-8)
-all the necessary valve actuators ST-230/2 (connectors 10-17)
-Internet module - via RS cable
-pump
-additional device (connector 18)
-heating / cooling device (connector 19)

7

8
Pictorial diagram presenting wiring and communication with other devices in the system:
Step 2. Mounting electrolytic capacitors
In order to reduce the phenomenon of fluctuation in the temperature read from the zone sensor, use a 220uF / 25V low
impedance electrolytic capacitor (GF 220U / 25V SAMXON) connected parallel to the sensor cable. When installing a
capacitor, pay special attention to polarization. The ground of the element marked with a white stripe should be screwed
into the right-hand side terminal of the sensor connector (looking at it from the front of the controller), which can be seen
in the attached photographs. The second terminal of the capacitor should be screwed into the left-hand side terminal of
the connector. So far the application of this solution has eliminated completely the occurring disturbances. It is worth
noting, however, that the basic principle is proper connection of wires to avoid disruption. The cable should not be placed
close to the sources of the electromagnetic field, but if this is the case, it is necessary to use a filter in the form of a capacitor.
Step 3. Switch on the power supply and check if the devices work
Once all the devices have been connected, switch on the power supply. Use manual mode to check if each device works -
use buttons ▲▼to select the device and press MENU button - the device should switch on. Follow this procedure to
check all the devices.

9
Step 4. Activate the Internet module
EU-L-7E external controller is compatible with ST-507 Internet module and WiFi RS.
WiFi RS uses WiFi wireless network whereas ST-507 needs to be connected to a router with RJ45 network cable.
Connection diagram for ST-507 Internet module.
Connection diagram for WiFi RS Internet module.
ST-507 Internet module or WiFi RS should be connected as illustrated in the diagrams above. Next, activate the module
in the controller menu: Main menu/Fitter’s menu/Internet module/ON. Further steps are described in detail in the
instruction manual for the Internet module.
NOTE
The user should enable the Internet module to connect with data servers listening on TCP/2000 port. Most
computer networks are protected by various software (firewalls, anti-virus software etc.) which may block data
exchange with the above mentioned port. If any problems arise, contact technical support or your computer
network administrator.

10
Step 5. Set current time and date
Set current time and date in the fitter’s menu.
Step 6. Configure the settings for temperature sensors, room regulators
To enable EU-L-7E to control a given zone, it is necessary to provide it with current temperature value. The easiest way is
to use C-7p temperature sensor.
The user may also choose M-7 room regulator.It serves as a master controller enabling the user to change the pre-set
temperatures in different zones,change the settings of the local and global weekly schedules etc. Only one room regulator
of this type may be installed in the heating system.
C-7p room temperature sensor –In order to activate the temperature sensor, use ON/OFF function in the
submenu of a given zone (Zones > Zones 1-8 > ON/OFF). It is possible to set individual pre-set temperature value
and weekly schedule for each room sensor assigned to a given zone. The settings may be configured both in the
controller menu (Main menu/Zones) and via www.emodul.eu (using ST-507 or WiFi RS module).
M-7 room regulator (control panel) –In order to activate M-7 room regulator (control panel), connect it to EU-L-
7E controller using RS cable and select <ON> in the external controller menu (Fitter’s menu > TECH regulator).
V. MAIN SCREEN DESCRIPTION
The user navigates in the menu structure using the buttons located next to the display.
1. Display.
2. ▲ - ‘up’, ‘plus’–it is used to view the menu options and increase the value while editing parameters. During
standard operation the button is used to switch between parameters of different zones.
3. ▼- ‘down’, ‘minus’- it is used to view the menu options and decrease the value while editing parameters.
During standard operation the button is used to switch between parameters of different zones.
4. MENU button –it is used to enter the controller menu and confirm the new settings.
5. EXIT button –it is used to exit the menu and cancel the settings
2
3
4
5
1

11
MAIN SCREEN
1. Current mode (flame–heating, snowflake –cooling)
2. An icon indicating pump operation
3. Voltage-free contact
4. Current time
5. Time left until the manually set temperature in a given zone changes
6. Information about the type of current weekly schedule
7. Pre-set temperature in a given zone (backlit number in the zone bar –see: description no. 9)
8. Current temperature of C-7p sensor in a given zone (backlit number in the zone bar –see: description no. 9)
9. Zone information:
The digit displayed indicates that the corresponding room sensor is connected and sends current
temperature information. If the zone temperature is too low, the digit flashes. In the event of a zone
alarm, an exclamation mark is displayed instead of the digit.
In order to view the operation parameters of a given zone, select its number using ▲or ▼.
1
2
3
4
5
6
7
8
9

12
MIXING VALVE SCREEN
1. Valve opening
2. External temperature rounded to whole degrees
3. Current mode (flame–heating, snowflake –cooling)
4. An icon indicating pump operation
5. Voltage-free contact
6. Current time
7. Current valve temperature
8. Pre-set valve temperature
9. Individual valve address (used for registration purpose)
VI. CONTROLLER FUNCTIONS
1. BLOCK DIAGRAM –CONTOLLER MENU
Main menu
Screen view Main screen
Mixing valve screen
Manual mode
Pump
Voltage - free contact
Valve 1-8
Zones
Voltage-free contact
Cooling
Heating
Heat pump
Delay
Language selection
Display contrast
Fitter's menu
Valve
Internet module
TECH regulator
Clock
Set date
Software version
1
2
3
4
5
6
7
8
9

13
2. SCREEN VIEW
In this submenu the user may change the main screen view:
•Main screen –including zones parameters e.g. pre-set temperature, current temperature etc.
•Mixing valve screen –including mixing valve operation parameters.
3. MANUAL MODE
This function enables the user to activate particular devices (pump, voltage-free contact and valve actuators) independently
of the others in order to check if they operate properly. It is advisable to check the devices using this procedure at the first
start-up.
4. ZONES
This menu is described in detail in section VII.
5. VOLTAGE-FREE CONTACT
Cooling –Once this function has been selected, the voltage-free contact will enable/disable cooling.
Heating –Once this function has been selected, the voltage-free contact will enable/disable heating.
Heat pump –Once this function has been selected, the voltage-free contact will enable/disable heating or cooling
depending on the status of the contact input.
Delay –This function enables the user to define the activation delay for the device connected to the voltage-free
contact. If cooling or heating is needed, the heating or cooling mode will be enabled after the pre-set delay time.
6. LANGUAGE SELECTION
This function is used to select the language version of the controller menu.
7. DISPLAY CONTRAST
This function is used to adjust the display contrast to individual needs.
8. FITTER’S MENU
Fitter’s menu is described in section VIII.
9. SOFTWARE VERSION
When this option is selected, the display shows the manufacturer’s logo and the controller software version.

14
VII. ZONES
10. BLOCK DIAGRAM –ZONES MENU
This submenu enables the user to configure operation parameters for particular zones.
11. OFF/ON
After the room sensor has been connected and registered in a given zone, it is used by EU-L-7E controller. The default
setting for this option is <OFF>. It may be activated when the room sensor has been connected.
12. PRE-SET TEMPERATURE
The pre-set zone temperature depends on the weekly schedule settings. However, this function enables the user to change
this value separately. After the value has been set, the user defines how long the temperature should apply. When the time
elapses, the pre-set temperature will depend on the weekly schedule again.
After pressing MENU button in this submenu, the display shows application time screen (permanent, temporary).
The main screen displays current pre-set temperature value and the time left (see: Main screen description).
13. WEEKLY CONTROL
EU-L-7E controller offers two types of weekly schedules:
Own –local schedule
This weekly schedule is assigned to a given zone only. After the room sensor has been detected by the external controller,
the schedule is activated automatically in this zone and may be adjusted by the user to individual needs.
Zone 1-8
OFF
ON
Pre-set temperature
Weekly control
Own
Schedules 1-5
Operation mode
Heating/Cooling
Only cooling
Only heatingCalibration
Hysteresis

15
Schedule 1-5 –global schedule
These schedules have universal settings for all zones and they cannot be edited in the external controller (to introduce
changes it is necessary to use M-7 control panel or connect to the Internet via the Internet module).
In order to assign a schedule to a given zone, choose Select option.
In order to adjust the global schedule as the current schedule in a given zone, choose Edit option. After the schedule has
been modified and saved, it is overwritten as a local schedule.
The type of weekly schedule assigned to a given zone is displayed in the main screen (See: Main screen description –screen
area no. 6).
14. OPERATION MODE
This option enables the user to exclude a given zone from certain operation algorithm:
Heating/cooling –when this option is selected, a given zone is not excluded from any operation algorithm (heating,
cooling).
Only heating –a given zone is active only in heating mode.
Only cooling–a given zone is active only in cooling mode.
15. CALIBRATION
Room sensor calibration should be performed while mounting or after it has been used for a long time, if the external
temperature displayed differs from the actual temperature. Calibration setting range is from -10 to +10⁰C with the accuracy
of 0,1⁰C.
16. HYSTERESIS
This function is used to define tolerance of the pre-set temperature in order to prevent undesired oscillation in case of
small temperature fluctuation (within the range 0 ÷ 15⁰C) with the accuracy of 0,1°C.
Example: if the pre-set temperature is 23⁰C and the hysteresis is 0,5⁰C, the zone temperature is considered too low when
it drops to 22,5⁰C.
VIII. FITTER’S MENU
Fitter’s menu should be accessed by a qualified person. It enables the user to configure additional functions of the
controller.
17. BLOCK DIAGRAM –FITTER’S MENU

16
Fitter's menu
Valve
Registration
Pre-set valve temperature
Valve status
Temperature monitoring
Opening time
Single stroke
Minimum opening
Valve type
Weather-based control
Return protection
External sensor correction
Factory settings
Valve removal
Internet module
OFF
ON
Registration
Software version
DHCP
IP address
IP mask
Gate address
DNS address
Module version
TECH regulator
OFF
ON
Clock
Set date

17
18. VALVE
EU-L-7E external controller may control an additional valve via valve module (e.g. ST-431N). The devices communicate
using RS communication but it is necessary to register first.
Registration - Configuring particular parameters of additional valve is possible only after it has been properly
registered by entering the module number (the number may be found at the back of the control module cover or
in Software version submenu).
Pre-set valve temperature - This function is used to define the pre-set valve temperature measured by the valve
sensor.
Valve status - This function is used to deactivate the valve temporarily. The valve may be activated again without
the need to register it again.
Temperature monitoring - This parameter determines the frequency of water temperature measurement
(control) behind the CH valve. If the sensor indicates a change in temperature (deviation from the pre-set value),
the electric valve will open or close by the pre-set stroke, in order to return to the pre-set temperature.
Opening time - This parameter defines the time needed for the valve actuator to open the valve from 0% to 100%
position. This value should be adjusted to the value given on the actuator rating plate.
Single stroke - This is the maximum single stroke (opening or closing) that the valve may make during one
temperature sampling. The smaller the single stroke, the more precisely the set temperature can be achieved.
However, it takes longer for the set temperature to be reached.
Minimum opening- The parameter determines the smallest valve opening. Thanks to this parameter, the valve
may be opened minimally, to maintain the smallest flow.
Valve type - this option is used to select the valve type:
•CH - select this option if you want to control CH circulation temperature.
•FLOOR - select this option if you want to control the floor heating temperature. It protects the underfloor
heating installation against dangerous temperature. If the user selects CH as the valve type and connects it to
the underfloor heating system, the fragile floor installation may be damaged.
Weather-based control - For the function of weather control to be active, the external sensor mustn't be exposed
to sunlight or influenced by the weather conditions. After it has been installed in an appropriate place, weather
control function needs to be activated in the controller menu.
In order for the valve to operate correctly, the user defines the pre-set temperature (downstream of the valve) for 4
intermediate external temperatures: -20ºC, -10ºC, 0ºC and 10ºC. In order to configure the pre-set temperature value,
use arrows UP and DOWN to select particular external temperature and use arrows UP and DOWN to set desired
temperature value.
Heating curve –it is a curve according to which the pre-set controller temperature is determined, on the basis of
external temperature. In our controller, this curve is constructed on the basis of four pre-set temperatures for
respective values of external temperatures.
The more points constructing the curve, the greater its accuracy, which allows its flexible shaping. In our opinion, four
points seem a very good compromise ensuring decent accuracy and easiness of setting the course of this curve.

18
NOTE
Once weather-based control has been activated, Pre-set valve temperature parameter is not available ( Main
menu --> Fitter’s menu --> Valve --> Pre-set valve temperature).
Return protection - This function enables the user to set boiler protection against too cool water returning from
the main circulation, which could cause low-temperature boiler corrosion. The return protection involves closing
the valve when the temperature is too low, until the short circulation of the boiler reaches an appropriate
temperature level. Once it is activated, the user presets the minimum acceptable return temperature.
External sensor correction - External sensor correction should be performed during installation or after a longer
period of using the regulator when the temperature measured by the sensor is different from actual temperature.
Range of regulation is -10 to +10 ºC with the accuracy of 0,1ºC.
Factory settings - This parameter is used to restore the factory settings of a given valve.
Valve removal - This option is used to remove the valve from the controller memory. Valve removal is used e.g. at
disassembling the valve or module replacement (re-registration of a new module is necessary).
19. INTERNET MODULE
Internet module is a device enabling the user remote control of
the regulator. The user may control the status of all system
devices on the home computer screen, tablet or smart phone and
adjust certain parameters via the Internet.
After switching the module on and selecting DHCP option, the
controller automatically downloads such parameters as IP
address, IP mask, gateway address and DNS address from the local
network.
The Internet module may be connected to EU-L-7E via RS cable.
Detailed description of the procedure is available in the Internet
module instruction manual.
NOTE
This type of control is available only after purchasing and connecting an additional controlling module ST-507 or
WiFi RS which is not included in the standard controller set.
20. TECH REGULATOR
Once <ON> option has been selected, M-7 regulator will be used by the external controller. The default setting for this
option is <OFF>. It may be activated when the room sensor has been registered and connected to the external controller.
21. CLOCK
This function is used to set current time.
22. SET DATE
This function is used to set date.

19
IX. OWN SCHEDULE SETTINGS
Once the schedule has been selected (Menu -> Zones -> Zone 1-8 -> Weekly control), the user may select, view and edit a
given schedule.
Schedule view screen:
1. Time periods.
2. Pre-set temperature for time periods.
3. Pre-set temperature outside time periods.
4. Days when the above settings will apply.
NOTE
The user may program 3 different time periods in a given schedule (with the accuracy of 15 minutes).
NOTE
Only own schedule (for a given zone) may be edited from the external controller. Global schedules 1-5 may be
edited only from M-7 control panel or Internet module (WIFI RS or ST-507).
Follow these steps to configure the schedule:
Use arrows UP and DOWN to set the starting time for the first
time period. Press MENU to confirm.
Use arrows UP and DOWN to set the finishing time for the first
time period. Press MENU to confirm.
1
2
3
4

20
Use arrows UP and DOWN to define the pre-set temperature for
the first time period. Press MENU to confirm.
Once the time periods are ready, use arrows UP and DOWN to
define the pre-set temperature which will apply outside these
periods. Press MENU to confirm.
Select the days when a given schedule will apply. Use UP arrow
to switch between days and DOWN arrow to select the days.
Selected days will be highlighted in white. Press MENU to
confirm.
When the schedules for all days are ready, confirm the settings by
pressing MENU. Active option will be highlighted in white.