Techly EXT-EF3000 User manual

P/N: IDATA EXT-EF3000
8059018368338
EN User's Manual
IT Manuale d’istruzione
WWW.TECHLY.COM
HDMI OPTICAL
FIBER EXTENDER

HDMI OPTICAL FIBER EXTENDER
Dear Customer
Thank you for purchasing this product. For optimum performance
and safety, please read these instructions carefully before connecting,
operating or adjusting this product. Please keep this manual for future
reference.
IMPORTANT SAFETY INSTRUCTION
INTENDED USE
We do not permit using the device in other ways like
described in this user’s manual. Use the product only
in dry interior rooms. Not attending to these regulations
and safety instruction might cause fatal accidents,
injuries, and damages to persons and property. The manufacturer/
supplier assumes no liability for damages caused by failure to
comply with the intended use.
To reduce risk of electric
shock, this product should
ONLY be opened by an
authorized technician when
service is required. Disconnect the product from mains and other
equipment if a problem should occur. Do not expose the product
to water or moisture.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
• Your product is not a toy and is not meant for children, because it
contains small parts which can be swallowed and can injure when
used inappropriately!
• Please install the system and devices attached to it in a way that
persons cannot be injured, or objects not be damaged for example
by dropping or stumbling.
• Please remove the packing materials, because children may cut
themselves on them while playing.
Furthermore, there is a risk of swallowing and inhalation of
incidentals and insulating material.
• Avoid places with high temperatures, or humidity, or places which
might come into contact with water. Do not install the product close
to openings of air conditioners, or at places with an excessive
amount of dust or smoke.
• Do not install the product at places subject to vibration, or
oscillation
• Do not modify and alter the product and any accessories! Do not
use any damaged parts.
EN - 2
WWW.TECHLY.COM
IT - 2
HDMI OPTICAL
FIBER EXTENDER

• Keep enough space around all devices for a good ventilation and
free motion and to avoid damages.
• Do not unplug the deive when it is in using, keep distance from
flammable and explosive devices.
• Power supply: DC 5V/2A, usage only the supplied power unit. Make
sure the specification marched if using 3rd party DC adapters. Do
not use the power supply if it is damaged.
INTRODUCTION
This is an HDMI over IP Optical fibe extender kit, including a transmitter
and a receiver. With this device, the 1080p@60Hz HDMI signal can be
extended up to 40 km through single-mode optical fiber. This HDMI
extender kit supports HDMI loop out, uni-directional IR passback,
RS-232 passthrough, and audio extraction through S/PDIF output
on the receiver. It supports point-to-point connection or one-to-many
connection through gigabit switch, and cascading of switches is
also supported. This extender kit is a reliable video transmission and
distribution solution which can be widely used in security monitoring,
rail transit, broadcasting, smart cities, home theatre and other fields.
FEATURES
• Adopting ipcolor PIXEL technology can realize uncompressed and
low-latency transmission.
• Support up to 1080p@60Hz resolution, including 1920x1200/1920x
1080, backward compatible.
• Support optical fiber transmission, the maximum transmission
distance of 40 kilometers.
• Support one-to-many connection through the gigabit switch, or
switch cascading.
• Support HDR10
• Support EDID Passback.
• Support RS-232 passthrough.
• With HDMI loop out on the trnasmitter.
• Support uni-directional IR passback.
• The transmitter has a 3.5 mm audio input for sound embedding, the
receiver has an independent 3.5 mm and S/PDIF audio output.
• Lightning protection, surge protection, ESD protection.
• Support steady 24-hour operation
EN - 3
WWW.TECHLY.COM
IT - 3
HDMI OPTICAL
FIBER EXTENDER

PACKAGE CONTENTS
Make sure your package includes the following items:
• Transmitter *1
• Receiver *1
• DC 5V 2A Power Adapter *2
• IR Blaster extension cable *1
• IR receiver extension cable *1
• SFP optical transceiver (T1310/R1550nm) * 1
• SFP optical transceiver (T1550/R1310nm) * 1
• Terminal block *2
• Mounting ear * 4
• Screws *10
• Terminal screws *2
• User Manual *1
INSTALLATION REQUIREMENTS
EN - 4
WWW.TECHLY.COM
IT - 4
HDMI OPTICAL
FIBER EXTENDER
ITEM DESCRIPTION REQUIREMENT
Signal source
device
PC, DVD, NVR, etc.
with HDMI port HDMI cable≤5m
Cable
LC single-mode
(default Config)
fiber optic
cable≤40km
LC multimode fiber fiber optic
cable≤300m
Display device
TV, projector, LED
screen, etc. with
HDMI port
HDMI cable≤5m
Fiber switch
Switch with SFP
ports (only required
for one-to-many and
switch cascading
connections)
Gigabit switch

PANEL DESCRIPTION
Transmitter
IR receiverIR blaster
HDMI IN
HDMI OUT
Speaker
TX RX
HDMI Display
HDMI D isplay
Video Source
Optical Fiber
1.2 One-to-many connection (through gigabit switch):
TX
Video Source
RX
Optical Fiber
HDMI OUT
HDMI OUT
HDMI OUT
HDMI IN
HDMI Display
HDMI D isplay
HDMI D isplay
HDMI D isplay
RX
Gigabit
Fiber Switch
RX
Gigabit
Fiber Switch
Gigabit
Fiber Switch * N
TX
RX
RX
HDMI OUT
HDMI OUT
HDMI IN
HDMI Display
HDMI Display
HDMI OUT
HDMI Display
Video Source
Optical Fiber
RX
EN - 5
WWW.TECHLY.COM
IT - 5
1
2
3 4 5
1Power indicator
(blue)
1) Light off: No power supply
2) Steady on: The power is on
3) Flash: The factory settings have
been restored
2
Data
transmission
indicator
(orange)
1) Light off: The transmitter and the
receiver have not established a
connection
2) Slow flash (every 1 second):
The transmitter and the receiver
are connected but no video data
transmission
3) Quick flash (every 200ms): The
video signal is connecting
4) Steady on: The video data is
transmitting
3IR OUT Connect with IR blaster extension
cable
4L/R IN Connect to the audio source device
with 3.5mm stereo audio cable
5RS-232
(GND/RxD/TxD)
Used for RS-232 passthrough and
command
HDMI OPTICAL
FIBER EXTENDER

IR receiverIR blaster
HDMI IN
HDMI OUT
Speaker
TX RX
HDMI Display
HDMI D isplay
Video Source
Optical Fiber
1.2 One-to-many connection (through gigabit switch):
TX
Video Source
RX
Optical Fiber
HDMI OUT
HDMI OUT
HDMI OUT
HDMI IN
HDMI Display
HDMI D isplay
HDMI D isplay
HDMI D isplay
RX
Gigabit
Fiber Switch
RX
Gigabit
Fiber Switch
Gigabit
Fiber Switch * N
TX
RX
RX
HDMI OUT
HDMI OUT
HDMI IN
HDMI Display
HDMI Display
HDMI OUT
HDMI Display
Video Source
Optical Fiber
RX
EN - 6
WWW.TECHLY.COM
IT - 6
6 7 8 9 10
6RESET
1) Press to restart
2) Press and hold for 5 seconds to
restore the factory settings, and
then let go when the power indicator
flashes
7SFP signal out Insert the SFP optical module
(T1310nm/R1550nm)
8HDMI IN Connect with HDMI source device
9HDMI OUT Connect with local HDMI display
device
10 DC5V Connect with DC 5V/2A power adapter
HDMI OPTICAL
FIBER EXTENDER

IR receiverIR blaster
HDMI IN
HDMI OUT
Speaker
TX RX
HDMI Display
HDMI D isplay
Video Source
Optical Fiber
1.2 One-to-many connection (through gigabit switch):
TX
Video Source
RX
Optical Fiber
HDMI OUT
HDMI OUT
HDMI OUT
HDMI IN
HDMI Display
HDMI D isplay
HDMI D isplay
HDMI D isplay
RX
Gigabit
Fiber Switch
RX
Gigabit
Fiber Switch
Gigabit
Fiber Switch * N
TX
RX
RX
HDMI OUT
HDMI OUT
HDMI IN
HDMI Display
HDMI Display
HDMI OUT
HDMI Display
Video Source
Optical Fiber
RX
Receiver
EN - 7
WWW.TECHLY.COM
1 6
2
3 4 5
1
Power indicator
(blue)
1) Light off: No power supply
2) Steady on: The power is on
3) Flash: The factory settings have
been restored
2
Data
transmission
indicator
(orange)
1) Light off: The transmitter and the
receiver have not established a
connection
2) Slow flash (every 1 second):
The transmitter and the receiver
are connected but no video data
transmission
3) Steady on: The video data is
transmitting
3IR OUT Connect with IR blaster extension
cable
4S/PDIF OUT Connect to the audio device with
digital optical audio cable
5L/R OUT Connect to the audio device with
3.5mm stereo audio cable
6RS-232
(GND/RxD/TxD)
Used for RS-232 passthrough and
command control
IT - 7
HDMI OPTICAL
FIBER EXTENDER

IR receiverIR blaster
HDMI IN
HDMI OUT
Speaker
TX RX
HDMI Display
HDMI D isplay
Video Source
Optical Fiber
1.2 One-to-many connection (through gigabit switch):
TX
Video Source
RX
Optical Fiber
HDMI OUT
HDMI OUT
HDMI OUT
HDMI IN
HDMI Display
HDMI D isplay
HDMI D isplay
HDMI D isplay
RX
Gigabit
Fiber Switch
RX
Gigabit
Fiber Switch
Gigabit
Fiber Switch * N
TX
RX
RX
HDMI OUT
HDMI OUT
HDMI IN
HDMI Display
HDMI Display
HDMI OUT
HDMI Display
Video Source
Optical Fiber
RX
INSTALLATION PROCEDURES
CONNECTION DIAGRAMS
1.1 One-to-one connection
IR receiverIR blaster
HDMI IN
HDMI OUT
Speaker
TX RX
HDMI Dis pla y
HDMI Display
Vid eo So urc e
Optical Fiber
1.2 One-to-many connection (through gigabit switch):
TX
Vid eo So urc e
RX
Optical Fiber
HDMI OUT
HDMI OUT
HDMI OUT
HDMI IN
HDMI Dis pla y
HDMI Display
HDMI Display
HDMI Display
RX
Gigabit
Fiber Switch
RX
Gigabit
Fiber Switch
Gigabit
Fiber Switch * N
TX
RX
RX
HDMI OUT
HDMI OUT
HDMI IN
HDMI Dis pla y
HDMI Dis pla y
HDMI OUT
HDMI Dis pla y
Vid eo So urc e
Optical Fiber
RX
EN - 8
WWW.TECHLY.COM
7 8 9 10
7RESET
1) Press to restart
2) Press and hold for 5 seconds
to restore the factory settings,
and then let go when the power
indicator flashes
8SFP signal input Insert the SFP optical module
(T1550nm/R1310nm)
9HDMI OUT Connect with HDMI display device
10 DC5V Connect with DC 5V/2A power adapter
IT - 8
HDMI OPTICAL
FIBER EXTENDER

1.2 One-to-many connection (through gigabit switch):
IR receiverIR blaster
HDMI IN
HDMI OUT
Speaker
TX RX
HDMI Dis pla y
HDMI Display
Vid eo So urc e
Optical Fiber
1.2 One-to-many connection (through gigabit switch):
TX
Vid eo So urc e
RX
Optical Fiber
HDMI OUT
HDMI OUT
HDMI OUT
HDMI IN
HDMI Dis pla y
HDMI Display
HDMI Display
HDMI Display
RX
Gigabit
Fiber Switch
RX
Gigabit
Fiber Switch
Gigabit
Fiber Switch * N
TX
RX
RX
HDMI OUT
HDMI OUT
HDMI IN
HDMI Dis pla y
HDMI Dis pla y
HDMI OUT
HDMI Dis pla y
Vid eo So urc e
Optical Fiber
RX
IR receiverIR blaster
HDMI IN
HDMI OUT
Speaker
TX RX
HDMI Dis pla y
HDMI Display
Vid eo So urc e
Optical Fiber
1.2 One-to-many connection (through gigabit switch):
TX
Vid eo So urc e
RX
Optical Fiber
HDMI OUT
HDMI OUT
HDMI OUT
HDMI IN
HDMI Dis pla y
HDMI Display
HDMI Display
HDMI Display
RX
Gigabit
Fiber Switch
RX
Gigabit
Fiber Switch
Gigabit
Fiber Switch * N
TX
RX
RX
HDMI OUT
HDMI OUT
HDMI IN
HDMI Dis pla y
HDMI Dis pla y
HDMI OUT
HDMI Dis pla y
Vid eo So urc e
Optical Fiber
RX
1.3 One-to-many connection (gigabit switch cascading):
2. Connection istruction
1) Connect the source device to the HDMI IN port of the transmitter
with an HDMI cable, and connect the HDMI OUT port of the
receiver to the display device with another HDMI cable.
2) If it's one-to-one connection, then use a LC fiber optic cable to
connect the SFP port of the transmitter and receiver. If it is one-
to-many connection, then use the gigabit switch as a bridge to
connect the transmitter and the receivers with the LC fiber optic
cables respectively.
3) If using HDMI loop out, connect the display device to the HDMI
OUT port of the transmitter.
EN - 9
WWW.TECHLY.COM
IT - 9
HDMI OPTICAL
FIBER EXTENDER

4) If you need another audio source instead of the HDMI audio source,
connect the audio source to the L/R IN port of the transmitter with
a 3.5mm stereo audio cable.
5) If you need to output additional audio sources from the receiver
or extend the L/R stereo audio only, connect the S/PDIF OUT
port of the receiver to the audio device with a digital optical audio
cable and/or connect the L/R OUT port of the receiver to the audio
device with a 3.5mm stereo audio cable.*
6) Plug the power supply into the devices to get started.
*
a) When the HDMI IN port of the transmitter is connected and the L/R
IN port is not connected, the HDMI audio source can output from
the HDMI OUT, S/PDIF OUT, and L/R OUT ports of the receiver
simultaneously.
b) When the HDMI IN port and the L/R IN port of the transmitter is
both connected, the L/R stereo audio source can output from
the HDMI OUT, S/PDIF OUT, and L/R OUT ports of the receiver
simultaneously.
c) When the L/R IN port of the transmitter is connected and the HDMI
IN is not connected, it can be used as an audio extender, the L/R
stereo audio source can only output from the L/R OUT port of the
receiver.
3. IR User Guide
IR receiverIR blaster
HDMI IN
HDMI OUT
Speaker
TX RX
HDMI Displa y
HDMI Display
Video Source
Optical Fiber
1.2 One-to-many connection (through gigabit switch):
TX
Video Sourc e
RX
Optical Fiber
HDMI OUT
HDMI OUT
HDMI OUT
HDMI IN
HDMI Displa y
HDMI Display
HDMI Display
HDMI Display
RX
Gigabit
Fiber Switch
RX
Gigabit
Fiber Switch
Gigabit
Fiber Switch * N
TX
RX
RX
HDMI OUT
HDMI OUT
HDMI IN
HDMI Displa y
HDMI Displa y
HDMI OUT
HDMI Displa y
Video Source
Optical Fiber
RX
IR receiverIR blaster
HDMI IN
HDMI OUT
Speaker
TX RX
HDMI Displa y
HDMI Display
Video Source
Optical Fiber
1.2 One-to-many connection (through gigabit switch):
TX
Video Sourc e
RX
Optical Fiber
HDMI OUT
HDMI OUT
HDMI OUT
HDMI IN
HDMI Displa y
HDMI Display
HDMI Display
HDMI Display
RX
Gigabit
Fiber Switch
RX
Gigabit
Fiber Switch
Gigabit
Fiber Switch * N
TX
RX
RX
HDMI OUT
HDMI OUT
HDMI IN
HDMI Displa y
HDMI Displa y
HDMI OUT
HDMI Displa y
Video Source
Optical Fiber
RX
1. Power
2. IR Signal
3. Null
1. Power
2. IR Signal
3. Grounding
1) IR blaster extension cable should plug in the IR OUT port of the
transmitter or receiver, IR receiver extension cable should plug in
the IR IN port of the transmitter or receiver.
2) The emitter of the IR blaster extension cable should be as close as
possible to the IR receiving window of the source device.
3)Point the remote control at the receiving head of the IR receiver
extension cable to operate.
EN - 10
WWW.TECHLY.COM
IT - 10
HDMI OPTICAL
FIBER EXTENDER