Phoenix Contact UM EN OPC 7015 User manual

User Manual
UM EN OPC 7015 / OPC 7022
Panel-PC with Touchscreen and Software-Keyboard,
15“,22”-Display with the frontsided protection IP65

UM EN OPC 7015/OPC 7022
8155_en_00 PHOENIX CONTACT

UM EN OPC 7015/OPC 7022
PHOENIX CONTACT 8155_en_00
AUTOMATION
User Manual
Panel-PC with Touchscreen and Software-Keyboard, 15“,22”-
Display with the frontsided protection IP65.
02/2011
Description: UM EN OPC 7015/OPC 7022
Revision: 00
This Manual is valid for
the Panel PCs OPC 7015/OPC 7022
PxC Description
2700763 OPC 7015 SEXP
2700764 OPC 7015 S W7U
2700765 OPC 7015 S
2700766 OPC 7015 P W7U
2700767 OPC 7015 P
2700768 OPC 7022 S W7U
2700769 OPC 7022 S
2700770 OPC 7022 P W7U
2700771 OPC 7022 P

UM EN OPC 7015/OPC 7022
8155_en_00 PHOENIX CONTACT
Please observe the following notes
In order to ensure the safe use of the product described, you have to read and understand this
manual. The following notes provide information on how to use this manual.
User group of this manual
The use of products described in this manual is oriented exclusively to qualified electricians or
persons instructed by them, who are familiar with applicable standards and other regulations
regarding electrical engineering and, in particular, the relevant safety concepts.
Phoenix Contact accepts no liability for erroneous handling or damage to products from Phoenix
Contact or third-party products resulting from disregard of information contained in this manual.
Explanation of symbols used and signal words
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
Danger:
This indicates a hazardous situation which, if not avoided, will result in death or serious
injury.
Warning:
This indicates a hazardous situation which, if not avoided, could result in death or serious
injury.
Caution:
This indicates a hazardous situation which, if not avoided, could result in minor or
moderate injury.
The following types of messages provide information about possible property damage and
general information concerning proper operation and ease-of-use.
Note:
This symbol and the accompanying text alerts the reader to a situation which may cause
damage or malfunction to the device, either hardware or software, or surrounding
property.
Note:
This symbol and the accompanying text provides additional information to the reader. It
is also used as a reference to other sources of information (manuals, data sheets,
literature) on the subject matter, product, etc.

UM EN OPC 7015/OPC 7022
PHOENIX CONTACT 8155_en_00
General terms and conditions of use for technical documentation
Phoenix Contact reserves the right to alter, correct, and/or improve the technical documentation and
the products described in the technical documentation at its own discretion and without giving prior
notice, insofar as this is reasonable for the user. The same applies to any technical changes that
serve the purpose of technical progress.
The receipt of technical documentation (in particular data sheets, installation instructions, manuals,
etc.) does not constitute any further duty on the part of Phoenix Contact to furnish information on
alterations to products and/or technical documentation. Any other agreement shall only apply if
expressly confirmed in writing by Phoenix Contact. Please note that the supplied documentation is
product-specific documentation only and that you are responsible for checking the suitability and
intended use of the products in your specific application, in particular with regard to observing the
applicable standards and regulations.
Although Phoenix Contact makes every effort to ensure that the information content is accurate, up-
to-date, and state-of-the-art, technical inaccuracies and/or printing errors in the information cannot
be ruled out. Phoenix Contact does not offer any guarantees as to the reliability, accuracy or
completeness of the information. All information made available in the technical data is supplied
without any accompanying guarantee, whether expressly mentioned, implied or tacitly assumed. This
information does not include any guarantees regarding quality, does not describe any fair marketable
quality, and does not make any claims as to quality guarantees or guarantees regarding the
suitability for a special purpose.
Phoenix Contact accepts no liability or responsibility for errors or omissions in the content of the
technical documentation (in particular data sheets, installation instructions, manuals, etc.).
The aforementioned limitations of liability and exemptions from liability do not apply, in so far as
liability must be assumed, e.g., according to product liability law, in cases of premeditation, gross
negligence, on account of loss of life, physical injury or damage to health or on account of the
violation of important contractual obligations. Claims for damages for the violation of important
contractual obligations are, however, limited to contract-typical, predictable damages, provided there
is no premeditation or gross negligence, or that liability is assumed on account of loss of life, physical
injury or damage to health. This ruling does not imply a change in the burden of proof to the
detriment of the user.

UM EN OPC 7015/OPC 7022
8155_en_00 PHOENIX CONTACT
Statement of legal authority
This manual, including all illustrations contained herein, is copyright protected. Use of this manual by
any third party is forbidden. Reproduction, translation, and public disclosure, as well as electronic
and photographic archiving or alteration requires the express written consent of Phoenix Contact.
Violators are liable for damages.
Phoenix Contact reserves all rights in the case of patent award or listing of a registered design.
Third-party products are always named without reference to patent rights. The existence of such
rights shall not be excluded.
How to contact us
Internet Up-to-date information on Phoenix Contact products and our Terms and Conditions can be found on
the Internet at:
http://www.phoenixcontact.com
Make sure you always use the latest documentation.
It can be downloaded at:
www.phoenixcontact.net/catalog .
Subsidiaries If there are any problems that cannot be solved using the documentation, please contact your
Phoenix Contact subsidiary.
Subsidiary contact information is available at www.phoenixcontact.com
Published by
PHOENIX CONTACT GmbH & Co. KG
Flachsmarktstraße 8
32825 Blomberg
DEUTSCHLAND
Telefon +49 - (0) 52 35 - 3-00
Telefax +49 - (0) 52 35 - 3-4 12 00
PHOENIX CONTACT
P.O. Box 4100
Harrisburg, PA 17111-0100
USA
Phone [phone]
Should you have any suggestions or recommendations for improvement of the contents and layout of
our manuals, please send your comments to
[email protected] .

UM EN OPC 7015/OPC 7022
PHOENIX CONTACT 8155_en_00
INDEX
1REMARKS .................................................................................................................................9
1.1RELEVANT DOCUMENTATION FOR THE DEVICE.................................................................................. 9
1.2DATA,FIGURES AND MODIFICATION.............................................................................................. 9
1.3TRADE MARKS ........................................................................................................................ 9
1.47ENVIRONMENTAL CONDITIONS................................................................................................. 10
1.5STANDARDS......................................................................................................................... 11
1.6EQUIPMENT VERSIONS ............................................................................................................ 11
1.7SCOPE OF DELIVERY............................................................................................................... 11
2OPERATING INSTRUCTIONS .......................................................................................................12
2.1OPERATING LOCATION............................................................................................................ 12
2.2DAMAGE DUE TO IMPROPER USE ................................................................................................ 12
2.3WARRANTY /REPAIR.............................................................................................................. 13
2.4TREATMENT AND DISPOSAL OF LITHIUM BATTERIES ......................................................................... 13
3INSTALLATION ........................................................................................................................14
3.1INSTALLATION OPTION............................................................................................................ 14
3.2EXTERNAL DIMENSIONS OF THE OPC 7013 MODEL ......................................................................... 15
3.3INSTALLATION LAYOUT FOR OPC 7013....................................................................................... 16
3.4EXTERNAL DIMENSIONS OF THE OPC 7015 MODEL ......................................................................... 17
3.5INSTALLATION LAYOUT FOR OPC 7015....................................................................................... 18
3.6EXTERNAL DIMENSIONS OF THE OPC 7022 MODEL ......................................................................... 19
3.7INSTALLATION LAYOUT FOR OPC 7022....................................................................................... 20
3.8ORDER OF INSTALLATION ........................................................................................................ 21
4COMMISSIONING.....................................................................................................................24
4.1AVAILABLE INTERFACES........................................................................................................... 24
4.2CABLE INSTALLATION ............................................................................................................. 24
4.3ORDER OF STEPS DURING COMMISSIONING................................................................................... 24
4.4CHECK FOR OPERATIONAL READINESS.......................................................................................... 25
5OPERATION ............................................................................................................................26
5.1FRONT CONTROL KEYS............................................................................................................ 26
5.2SOFT KEYBOARD ................................................................................................................... 27
5.3TOUCH SCREEN..................................................................................................................... 28
5.4STATUS INDICATORS .............................................................................................................. 28
6INTERFACES............................................................................................................................29
6.1INTERFACE SETUP.................................................................................................................. 29
6.224 VDC POWER SUPPLY ......................................................................................................... 29
6.3USB CONNECTIONS ............................................................................................................... 29
6.4NETWORK CONNECTION (RJ45)................................................................................................ 30
6.5SERIAL COM INTERFACE (RS232)............................................................................................. 30
6.6EXTERNAL DRIVES ................................................................................................................. 31
7DRIVES..................................................................................................................................32
7.1HARD DRIVE /SSD FLASH MEMORY............................................................................................ 32

UM EN OPC 7015/OPC 7022
8155_en_00 PHOENIX CONTACT
8SOFTWARE &DRIVER INSTALLATION .......................................................................................... 33
8.1INSTALLING THE OPERATING SYSTEM ...........................................................................................33
8.2TOUCH SCREEN DRIVER INSTALLATION .........................................................................................34
8.3SOFT KEYBOARD....................................................................................................................34
9COMPONENT REPLACEMENT ....................................................................................................... 35
9.1OPENING THE SERVICE SLOT .....................................................................................................35
9.21. HDD (HARD DISK)REPLACEMENT ...........................................................................................37
9.32. FAN REPLACEMENT..............................................................................................................38
9.43. WORKING MEMORY (RAM) REPLACEMENT .................................................................................39
9.54. REPLACING THE LITHIUM BATTERY...........................................................................................40
9.65. REPLACING THE FLASH MODULES.............................................................................................41
nike Hinweise/W irüber uns/Wir über uns @ 2\mod_1254923190378_6.doc @ 6522 @Pos: 2 /Datentechnik/ Allgemeine Hinweis e/Relevante Doku mentationen zum Gerät/ Relevante Dokumentation en für OPC / CPC / OTC / VMT /STC @ 2\mod_1268 662117522_6.doc @ 7352 @

UM EN OPC 7015/OPC 7022
PHOENIX CONTACT 8155_en_00
1REMARKS
1.1 RELEVANT DOCUMENTATION FOR THE DEVICE
The following documents are essential for setting up and operating this device:
USER MANUAL (THIS DOCUMENTATION):
Contains information for installation, commissioning and operating the device along with
technical data of the device hardware.
Pos: 3 /Datentechnik/ Allgemeine Hinweise/ Erläuterung zu den verwendeten Symbolen/Erl äuterung zu den verwend eten Symbolen @ 0\mod_11 58752779484_6.doc @ 141 @
Pos: 4 /Datentechnik/Allge meine Hinweise/Daten, Abbildun gen, Änderungen/Daten,Ab bildungen,Änderungen @ 1\mod_12 35480498775_6.doc @ 5162 @
1.2 DATA,FIGURES AND MODIFICATION
All texts, data and figures are non-binding. All these materials are subject to modification
due to technological advances. Our products comply with all provisions and requirements
of the legislation at the point in time when the products leave our company premises. The
operator/operating company bears sole responsibility for the compliance with any
consecutive new technological requirement and adherence to any consecutive new
legislatory provision, as well as for the observance of their obligation as the
operator/operating company.
Pos: 5 /Datentechnik/ Allgemeine Hinweise/ Warenzeichen/W arenzeichen @ 2\mod_12632981 82965_6.doc @ 6972 @
1.3 TRADE MARKS
We would like to emphasise that all names of hardware and software products used in this
documentation, as well as all brand names of corresponding companies are subject to the
general copyrights of the intellectual property in terms of trademarks, brand names and
patents.
Windows®, Windows®CE are registered trademarks of Microsoft Corp.
Intel®, Pentium®, Atom™, Core™2, are registered trademarks of Intel Corp.
IBM®, PS/2®and VGA®are registered trademarks of IBM Corp.
CompactFlash®is a registered trademark of the Compact Flash Association.
RITTAL®is a registered trademark of Rittal Werk Rudolf Loh GmbH & Co. KG.
Any other national and international trademarks and product names shall hereby also be
recognised.
Pos: 6 /Datentechnik/ Allgemeine Hinweise/ Urheberrecht/ Urheberrecht @ 0\mod_115875 6954232_6.doc @ 153 @

UM EN OPC 7015/OPC 7022
8155_en_00 PHOENIX CONTACT
Pos: 7 /Datentechnik/ Allgemeine Hinweise/ Umweltbedingungen/ Umwelbedingungen f ür OPC 7013 / 7015 / 7022 @ 2\mod_125732 5662755_6.doc @ 6783 @
1.4 7ENVIRONMENTAL CONDITIONS
The device may be operated under the following conditions. Failure to observe these
specifications will terminate any warranty for this device. Phoenix Contact cannot be held
liable for any damages arising due to improper use and handling.
Temperature for OPC7008
In operation -20 … +55°C*
(*only with Flash SSD)
for storage -30 … +75°C
Temperature for devices OPC 7013/7015
In operation +5 … +45°C
In operation -20 … +60°C*
(*valid only with Flash SSD, Automotive HDD or 2,5" Industrial SSD)
for storage -30 … +65°C
for storage -30 … +75°C*
(*valid only with Flash SSD, Automotive HDD or 2,5" Industrial SSD)
Temperature for device OPC 7022
In operation +5 … +45°C
for storage -20 … +60°C
Humidity:
In operation 10 … 85% without condensate
For storage 10 … 85% without condensate
Vibration resistance
In operation 1 G, 10 … 500 Hz
(DIN EN 60068-2-6)
Shock resistance
In operation 5 G, with a half-wave of 30 ms duration
(DIN EN 60068-2-27)
Pos: 8 /Datentechnik/ Allgemeine Hinweise/ Normen/Normen @ 1\mod_121 9145812377_6.doc @ 3945 @

UM EN OPC 7015/OPC 7022
PHOENIX CONTACT 8155_en_00
1.5 STANDARDS
This device complies with the requirements and protective aims of the following EC
regulations:
This device meets the test requirements for granting the CE sign according to the
European test standards EN 61000-6-4 and EN 61000-6-2.
This device complies with the test requirements in accordance with EN 60950
(VDE0805, IEC950) "Safety of Information Technology Equipment"
The device meets the EN 60068-2-6 standard test requirements (sinus excitation).
The device meets the EN 60068-2-27 standard test requirements (shock resistance
test).
Note:
A respective conformity declaration for the authority in charge is available at the
manufacturer and may be viewed on request.
All connected components, as well as cable connections must also meet these
requirements for compliance with the EMC legislation. For this reason, screened bus and
LAN cables including screened connectors must be used and installed according to the
instructions in this user manual.
Pos: 9 /Datentechnik/ Allgemeine Hinweise/ Ausstattungsvar ianten/Ausstattung svarianten für OPC6000/ 7000 @ 2\mod_1265643750 549_6.doc @ 7192 @
1.6 EQUIPMENT VERSIONS
The system is available in two equipment versions:
Platform including a Flash SSD:
Without any rotating mass storage device (hard disk, etc.) and including an embedded
operating system (Windows CE / XP embedded) for stationary use.
Platform including a hard disc:
Equipped with a hard disk for stationary use with a standard operating system, e.g. for
applications in the manufacturing department.
Pos: 10 /Datentechnik/ Allgemeine Hinweise/ Lieferumfang/Lief erumfang für OPC7008 / 7013 / 7015 / 7022 @ 2\mod_125732 0771863_6.doc @ 6773 @
1.7 SCOPE OF DELIVERY
Please check that all of the following components are contained in the packaging:
1 x device
With 24 V DC devices: 3-pin lead-through plug from Phoenix Contact, 3-pin 3.81
OPC7 with a screw connection (already connected with
device socket)
Service CD
Optional delivery scope
Operating system
Pos: 11 /Datentechnik/Betr iebshinweise/Betriebs ort/Betriebsort für OPC-Ser ie / IPC- Serie / CPC- Serie / PLC-Serie / ITC-Serie / OTC-Serie @ 0\mod_11588 27335567_6.doc @ 217 @

UM EN OPC 7015/OPC 7022
8155_en_00 PHOENIX CONTACT
2OPERATING INSTRUCTIONS
This device contains electrical voltages and extremely sensitive components. User
intervention is restricted to plugging in additional cards only. The manufacturer or a
service partner authorised by the manufacturer should be consulted if you plan to make
further modifications. For this type of work, the device must be switched off at the mains
and the power lead must be disconnected. Suitable measures for avoiding electrostatic
discharge towards parts of the components when touching the equipment must be taken.
If the device is opened by an unauthorised person, hazards for the user might arise and
any warranty claim will cease.
General instructions:
All users must read this manual and have access to it at all times.
Installation, commissioning and operation may only be carried out by trained and
qualified staff.
The security instructions and the manual itself must be observed by all persons
who work with this device.
At the location of use the valid guidelines and regulations for accident prevention
must be observed.
The manual contains the most important instructions on how to use this device in
a safe way.
Appropriate storage, proper transport, installation and commissioning, as well as
careful operation are prerequisites for ensuring safe and proper operation of the
device.
Warning:
Any leads (e.g. power leads, interface cables) may only be connected if the device is
switched off in order to avoid damaging the device.
2.1 OPERATING LOCATION
The control system is designed for use inside a switching cabinet. You must ensure
compliance with the specified environmental conditions. Using the device in non-specified
environments, for example, on board ships, or in areas that might contain explosive gases
or in extreme heights is prohibited.
Warning:
The device may only be switched on after acclimatising to the ambient temperature in
order to avoid condensate accumulation. The same applies if the device has previously
been exposed to extreme temperature variations.
To avoid overheating: The device must not be exposed to direct radiation by sunlight or
any other light or heat source.
If the device is integrated in a panel, casing or similar enclosures, you must ensure that
no heat accumulation builds up. The maximum permissible environmental temperature
must never be exceeded.
Pos: 12 /Datentechnik/ Betriebshinweise/ Schäden durch unsachge mäßen Gebrauch/Schäden d urch unsachgemäßen Gebr auch @ 0\mod_1158827867958 _6.doc @ 221 @
2.2 DAMAGE DUE TO IMPROPER USE
If the control system shows any obvious damage, e.g. caused by improper operating or
storage conditions or by improper use or handling, you must immediately put the device
out of operation and protect it from being accidentally switched on.
Pos: 13 /Datentechnik/ Betriebshinweis e/Gewährleistung / Repar atur/Gewährleis tung / Reparatur @ 0\mod_1158 828054427_6.doc @ 223 @

UM EN OPC 7015/OPC 7022
PHOENIX CONTACT 8155_en_00
2.3 WARRANTY /REPAIR
During the warranty period, any repair must be carried out by the manufacturer or by
persons duly authorised by the manufacturer only.
Pos: 14 /Datentechnik/ Betriebshinweis e/Behandlung und Entsor gung von Lithium-Bat terien/Behandlung und E ntsorgung von Lithium-Ba tterien @ 1\mod_124 7056308470_6.doc @ 5922 @
2.4 TREATMENT AND DISPOSAL OF LITHIUM BATTERIES
This device contains a lithium battery for supplying the system clock with power as long as
the supply voltage is not connected. The battery has a life cycle of 3 - 5 years depending
on which load is applied.
Note:
The more the battery is exposed to higher temperatures, the faster it ages.
Warning:
There is an acute risk of explosion should the wrong type of battery be used.
Warning:
Do not put lithium batteries into a fire, do not solder on the cell body, do not recharge
them, open them, short-circuit them, do not reverse their polarity or heat them up over
100°C; dispose of them properly and protect lithium batteries from direct sun light,
humidity and condensation.
Lithium batteries may only be replaced by the same type, or by a type recommended by
the manufacturer.
The lithium battery must be disposed of according to the local legislation at the end of its
life cycle.
Pos: 15 /Datentechnik/ Montage/Montage möglichkeiten/Mon tagemöglichkeit für OPC7008 / 7013 / 7015 / 7022 @ 2\mod_1257 329372078_6.doc @ 6802 @

UM EN OPC 7015/OPC 7022
8155_en_00 PHOENIX CONTACT
3INSTALLATION
3.1 INSTALLATION OPTION
This device is intended for integration into switch panels or switching cabinets. In order to
allow for a safe installation and operation (connector access), these switch panels or
control desks must be accessible from the back. The device can be integrated into
switching cabinets with a wall thickness of 2 to 13 mm. We recommend a minimum of 3
mm for correct installation with an IP65 front protection class.
Warning:
To avoid overheating in operation: The device must not be exposed to direct radiation by
sunlight or any other light or heat source.
If the device is integrated in a panel, casing or similar enclosures, you must ensure that
no heat accumulation builds up. The maximum permissible environmental temperature
must never be exceeded.
Devices including a data drive must only perpendicularly be integrated. Any deviation
must be agreed with Phoenix Contact.
The IP65 protection class is only achieved after correct installation.
Note:
When selecting the enclosure for integration, the power dissipation total of the system
including that of all integrated PCBs must be taken into account. The enclosure must be
calculated in such a way that the maximum environmental temperature is not exceeded in
any case.
Pos: 16 /Datentechnik/ Montage/Montages kizzen/Außenabmessung en des Geräts/Montag eskizze des Geräts OPC 701 3 / 7015 / 7022 @ 2\mod_1257325 856744_6.doc @ 6786 @

UM EN OPC 7015/OPC 7022
PHOENIX CONTACT 8155_en_00
3.2 EXTERNAL DIMENSIONS OF THE OPC 7013 MODEL

UM EN OPC 7015/OPC 7022
8155_en_00 PHOENIX CONTACT
3.3 INSTALLATION LAYOUT FOR OPC 7013

UM EN OPC 7015/OPC 7022
PHOENIX CONTACT 8155_en_00
3.4 EXTERNAL DIMENSIONS OF THE OPC 7015 MODEL

UM EN OPC 7015/OPC 7022
8155_en_00 PHOENIX CONTACT
3.5 INSTALLATION LAYOUT FOR OPC 7015

UM EN OPC 7015/OPC 7022
PHOENIX CONTACT 8155_en_00
3.6 EXTERNAL DIMENSIONS OF THE OPC 7022 MODEL

UM EN OPC 7015/OPC 7022
8155_en_00 PHOENIX CONTACT
3.7 INSTALLATION LAYOUT FOR OPC 7022
Pos: 17 /Datentechnik/ Montage/Reihenfo lge der Montage/Reihenf olge der Montage für OPC 7013 / 7015 / 7022 @ 2\mod_12573259570 19_6.doc @ 6790 @