Techni Sport RTA-TS205 User manual

Imported By
Thank you for purchasing one of our products.
Please read carefully the assembly instructions before the installation.
Do not discard this manual or any of the packaging material until the unit
has been completely assembled.
MODEL RTA-TS205
ASSEMBLY INSTRUCTIONS

❶
x1 ❷
x1 ❸
x2 ❹
x1
❻
x1
❺
x2 ❼ x1
🅐
x8
🅑
x8
🅒
x4
🅓
x4
🅔
x1
P.2
RTA-TS205
P.2
Main panel Upper shelf panel Main structures Lower back structure
Horizontal tubes Headset hanger Cup holder
M6x42mm M6x32mm 4x15mm Studs Allen wrench
MAIN PARTS LIST
HARDWARE

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
P.3
RTA-TS205
P.3
❶Do a quick inventory to
make sure the package
contains all the parts and
hardware listed in the
assembly instructions.
❷Missing, damaged and
defective parts can be
replaced at no cost to you.
Please refer to the CONTACT
card included with the
product.
❸The replacement parts service
is limited to the continental United
States. If you reside in Hawaii,
Puerto Rico, U.S. Dependencies
or other countries, please contact
the supplier from where the unit
was purchased.
❹If during assembly you
find an issue or need
clarification, please contact
our Customer Service for
assistance. Please refer to the
CONTACT card included with
the product.
❺On each step read the
instructions and analyze the
illustrations thoroughly
before proceeding to do the
assembly.
❽Do not overtighten
or force the screws as
they might break, strip,
damage the threads of
the holes or get stuck
inside the part.
❻Make sure you understand
which hardware will be used
on each step. Using the wrong
size of screw, bolt or pin might
strip the threads or cause
damage to the part in which it
is being used.
❼To avoid misalignments,
always leave the screws
loose and tighten them until
all pieces are positioned
correctly.
❾Sometimes the laminate might cover partially or
entirely the hole on a panel. If there is no visible hole for
the screw, pass and press the tip of your finger over the
area where the hole should be located to feel the
indentation, and once found, carefully pierce the laminate
to reveal the hole underneath.
❿If the hole seems too small for the screw, first make
sure you are using the correct size of screw and that it’s
been installed in the correct hole. If the hole still appears to
be too small, carefully pierce the laminate to reveal the
hole’s actual size. √

STEP 1
Hardware/Tools:
🅓
4
Pcs
Insert the studs Ⓓinto the bottom holes of the structures ③.
Assemble the lower back structure ④and the horizontal tubes ⑤to the main structures
③using screws Ⓐas shown.
STEP 2
Hardware/Tools:
🅐
M6x42mm
8
Pcs
🅔
P.4
RTA-TS205
P.4
ASSEMBLY STEPS
③
③

Assemble the upper shelf panel ②to the main structures ③using screws Ⓑfrom
underneath.
Assemble the main panel ①to the main structures ③using screws Ⓑfrom underneath.
P.5
RTA-TS205
P.5
STEP 3
Hardware/Tools:
🅑
M6x32mm
4
Pcs
🅔
STEP 4
Hardware/Tools:
🅑
M6x32mm
4
Pcs
🅔
③
③
③
③

Using screws Ⓒand from underneath, assemble to the front side corners of the main panel
①the headset hanger ⑤and the cup holder ⑥on the side of your preference.
OR:
P.6
RTA-TS205
P.6
①
STEP 5
Hardware/Tools:
🅒
4x15mm
4
Pcs
🅔
⑦
⑥
⑦
⑥
DONE! Before you start using the unit, make sure that all the screws, bolts, etc. are properly
tightened, and read all the warnings in the next page.
⑥
⑦

AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING
CARE AND MAINTENANCE WARNINGS:
•Do not exceed the indicated weight limits.
•Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
•Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry
with a clean towel.
•Do not use solvents or abrasive materials to clean the unit.
•If you decide to use a cleaning agent, test first on an area hidden from view such as underneath the
tabletop.
•Do not seat on the unit or lean against it.
•Do not allow small children to play under the unit or climb on the desktop and top shelf.
•The unit must be handled by at least 2 persons when moving in the same or adjacent rooms.
•Before moving the unit, make sure to remove any object that is heavy or might fall off.
•When lifting the unit, use both hands and bend your knees, not your backs.
•When transporting the unit to places far away, protect and secure the unit to avoid damage in transit.
•Shall any part of the unit become defective during the warranty period, replacement parts might be
available to you at no charge. Please refer to the WARRANTY card included with the product.
•The warranty does not extend to regular wear and tear, nor the manufacturer assumes liability for
damages or consequences due to accidents, incorrect assembly, negligence, improper use, modifications,
or not heeding the above warnings.
•The warranty is limited to the continental United States. If you reside in Hawaii, Puerto Rico, U.S.
Dependencies or other countries, please contact the supplier from where the unit was purchased.
P.7
RTA-TS205
P.7
WEIGHT LIMITS
2.2 Lbs. (1 Kg)
11 Lbs. (5 Kg)
2.2 Lbs. (1 Kg)
44 Lbs. (20 Kg)