Techni Sport RTA-TS83 User manual

ASSEMBLY INSTRUCTIONS FOR TECHNI SPORT CHAIR MODEL
RTA-TS83
PARTS LIST
ATTENTION: Before you begin the assembly,
make sure that all parts are included in good
condition.
ATTENTION:
⚠Follow the in truction tep by tep.
⚠To avoid mi alignment , leave the crew loo e and do not tighten them until all are in their re pective place .
⚠Do not overtighten or force the crew a they could break, trip, or damage the thread of the hole .
⚠U ing the wrong ize of crew on a part could re ult in damage to the crew or the part.
C
E
F
H
M (x6)
G
J (x6)
N (x6)
B
D
N (x4)
M (x4)
I (x4)
Q
L
P
ABackrest, x1
BSeat, x1
CR
DMechanism,
x1
EHydraulic
Gas Lift, x1
Fovers for
Gas Lift, x1 set
GStar Base, x1
Haster, x5
I
J
M6x12mm, x2
K
M8x25mm, x10
L
O’ ring, x14
M
Washers, x14
N
Bracket covers,
O
P
QLumbar Pillow,
x1
Neck Pillow, x1
J
K (RIGHT)
FIRST REMOVE AND DISCARD THE
PLASTIC CAP FROM THE TOP OF THE
GAS LIFT (E).
In ert the ca ter (H) into the leg of the
ba e (G) u ing pre ure, then place
the ga lift (E) in the middle of the ba e,
and cover it with (F) a hown.
Place the eat (B) up ide-down with
it front end away from you a hown.
U ing crew (I), O’ ring (M) and wa her
(N), a emble the mechani m (D) to the eat
with it handle on your LEFT.
With the eat po itioned a hown,
a emble the armre t (C) to the eat
frame on their re pective ide u ing
crew (K), O’ ring (L) and wa her (M).
U ing crew (J), O ’ring
(M) and wa her (N),
a emble the backre t (A)
to both metal bracket on
the eat (B) a hown. Then attach both bracket cover (K) to the
bracket u ing crew (L).
Place the top over the ba e, making ure
the tip of the ga lift enter into the hole of
the mechani m.
(Front end of eat)
CL
Right Arm Left Arm
M8x20mm, x4
(Backrest, armrests)
(Brackets overs)
Hole overs, x4
C
(If the eat i
po itioned a
hown, the
RIGHT armre t
Will go on the
LEFT)
Make ure that all crew are tightened
before you it on the chair for the fir t
time.
RIGHT LEFT
REMOVE
PLASTIC
CAP!
(Mechanism)
A
N
M
K (LEFT)
L
RAllen Wrench,
x1
Cover the bracket hole with (O).
Attach the lumbar pillow (Q) fir t
and the neck pillow (P) a hown,
and fa ten the buckle on the back.
O
(RIGHT)
(LEFT)

HAIR’S FUN TIONS:
(1) To raise or lower the chair’s height, pull UP the lever that is under the seat. The chair goes down while
sitting on it, or up if you lift your body.
(2) To make the chair tilt, pull the same lever OUT horizontally to unlock this function, and IN to lock again.
(3) To adjust the tension for the tilting function, turn the mechanism’s knob in either direction to apply more
or less tension.
(4) To make the backrest recline, pull UP the lever that is located on the rear right side of the seat and release
it when the desired position is reached.
WARNING: For your safety, the chair’s tilt function in the mechanism should be in the LO KED (IN)
position prior to use the backrest reclining function.
(5) To adjust the armrest height, pull UP the button that is under the armrest and release it once the
desired height is reached.
(6) To adjust the armrests sideways, just turn them manually to the desired position right to left or left to right.
WARNINGS:
•Do not stand up on the chair or use it as ladder.
•Use the chair to seat only one person at a time.
•Do not use the chair if parts are damaged or if screws are loose or missing.
•Do not seat near the edge of the seat and always sit properly on the chair to avoid going beyond your balance point and fall off the chair.
•The chair is intended for teenagers and adults. If small children are using the chair, please keep close observation on them.
•Do not allow small children to play with the chair.
•Not paying attention to these warnings could result in severe injuries.
ARE AND MAINTENAN E:
•To clean the chair it is recommended to use a soft cloth lightly damped in a solution of smooth soap and water, then dry with a clean towel.
•Do not use solvents or abrasive materials to clean any part of the chair.
•Before applying a cleaning agent, test on a small hidden area of the chair, like underneath the seat.
•Do not expose the product to direct sunlight or to extreme environmental conditions.
•Every 4 months, inspect the chair completely and make sure that all screws are tighten.
(1)/(2)
(3)
(4)
(6)
(5)