Techni Sport TS42 User manual

GAMING CHAIR RTA MODELS
TS42, TS43,
TS50, TS51, TS52,
TS60, TS61, TS62C, TS63C.
ATTENTION:
⚠Follow the instructions step by step.
⚠To avoid misalignments, leave the screws loose and do not tighten them until all are in their respective places.
⚠Do not overtighten or force the screws as they could break, strip, or damage the threads of the holes.
⚠Using the wrong size of screws on a part could result in damage to the screw or the part.
ASSEMBLY INSTRUCTIONS
AB C-L DEFGH
KL
C-R I-L
I-R J-N J-L
Backrest Seat Left Armrest Right Armrest Mechanism Gas Lift Covers for gas
lift, set of 3 pcs
5-leg star base Casters, 5 pcs. Left cover for
seat bracket
Right cover for
seat bracket
Neck pillow * Lumbar pillow * Allen wrench
STEP
1
Insert the casters Ⓗinto the legs of the base
Ⓖusing pressure, then place the gas lift Ⓔin
the middle of the base and cover it with Ⓕ.
STEP
3
STEP
4
* When sitting on chair, not looking at it
M8x20mm with
felt gasket,
4 pairs.
Ⓖ
Ⓔ
Ⓗ
Ⓕ
C-L C-R
Ⓐ
Put the seat over the base parts making sure the tip of
the gas lift enters into the hole of the mechanism, then
assemble the backrest Ⓐto the metal brackets on
both sides of the seat Ⓑusing screws Ⓜ, O-rings Ⓞ
and washers Ⓟ.
Ⓑ
ⓄⓅ
O-Ring in
the middle!
Ⓜ
Attach the covers and to the brackets on their
respective sides of the seat Ⓑusing screws Ⓝand
cover the holes with ⓆAs shown.
I-L I-R
STEP
5
I-R I-L
LEFT
RIGHT
Ⓑ
ⓃⓆ
For pillows with straps, first attach the lumbar pillow
then the neck pillow by fastening the buckles
behind the backrest Ⓐas shown.
J-L
J-N
STEP
6
Ⓐ
(This shows
The chair
from behind)
J-N
J-L
(Mechanism)
MNOPQ
M8x25mm,
12 pcs
M6x12mm,
2 pcs
O-Ring,
16 pcs
Washers,
16 pcs
(Armrest, Backrest) (Brackets Covers)
Hole covers,
2 pcs
STEP
2
Note: The armrest side is determined by you sitting on the chair, not looking at it
(Back)
(*) Except TS61 and TSC62C
* The shape of these 2 pieces varies on each model.
* TS61 & TS62C don’t not come with lumbar pillow.
Ⓛ
Ⓞ
Ⓟ
O-Ring in
the middle!
Ⓓ
Ⓑ
(Back)
IMPORTANT:
Felt gasket goes
over the seat’s
hole!
Flip over the seat Ⓑwith its back end towards you, peel and place
the felt gasket Ⓛover the holes on the seat, and using screws Ⓛ,
O-rings Ⓞand washers Ⓟ, assemble the mechanism Ⓓwith its
handle facing to the LEFT as shown. 4 sets:
C-L
LEFT
C-R
RIGHT
Ⓑ
Ⓞ
Ⓟ
O-Ring in
the middle!
8 sets:
Ⓜ
Assemble the armrests and in their respective
sides of the seat Ⓑusing screws Ⓜ, O-rings Ⓞand
washers Ⓟ.
*

CHAIR’S FUNCTIONS:
①To raise or lower the chair’s height, pull UP the lever that is under the seat.
The chair goes down while sitting on it, or up if you lift your body.
②To make the chair tilt, pull the same lever OUT horizontally to unlock this
function, and IN to lock again. Please note that unlike regular office chairs,
gaming chairs have their base components off-center, and the tilting won’t
be much and might actually feel hard to tilt.
③To adjust the tension for the tilting function, turn the mechanism’s knob in
either direction to apply more or less tension. With less tension, the tilting
will feel easier.
④To make the backrest recline, pull UP the lever that is located on the rear
right side of the seat and release it when the desired position is reached.
WARNING: For your safety, the chair’s tilt function ②should be in the
LOCKED (IN) position prior to use the backrest reclining function.
⑤To adjust the armrest height, pull UP the button that is under the armrest
and release it once the desired height is reached.
⑥The armrests rotate ±25º, just adjust them manually.
WARNINGS:
• Do not stand up on the chair or use it as ladder.
• Use the chair to seat only one person at a time.
• Do not use the chair if parts are damaged or if screws are loose or missing.
•Do not sit near the edge of the seat and always sit properly on the chair to
avoid going beyond your balance point and fall off the chair.
• The chair is intended for teenagers and adults. If small children are using the
chair, please keep close observation on them.
• Do not allow small children to play with the chair.
• Not paying attention to these warnings could result in severe injuries.
CARE, MAINTENANCE AND WARRANTY:
•To clean the chair it is recommended to use a soft cloth lightly damped in a solution
of smooth soap and water, then dry with a clean towel.
•Do not use solvents or abrasive materials to clean any part of the chair.
•Before applying a cleaning agent, test on a small hidden area of the chair, like
underneath the seat.
•Do not expose the product to direct sunlight or to extreme environmental conditions.
•Every 4 months, inspect the chair completely and make sure that all screws are
tighten.
•Shall any part of the unit become defective during the warranty period, replacement
parts might be available to you at no charge. Please refer to the WARRANTY card
included with the product.
•The warranty does not extend to regular wear and tear, nor the manufacturer
assumes liability for damages or consequences due to accidents, incorrect
assembly, negligence, improper use, modifications, or not heeding the warnings.
•The warranty is limited to the continental United States. If you reside in Hawaii,
Puerto Rico, U.S. Dependencies or other countries, please contact the supplier
from where the unit was purchased.
Before seating and using the chair for the first time,
make sure that all screws are properly tightened.
③
⑥
④
①
②
⑤
TS42, TS43, TS63C:
250 Lbs (113 Kg)
TS50, TS51, TS52,
TS60, TS61, TS62C:
300 Lbs (136 Kg)