Technibel KPA8FIA0R5IBA User manual

EG
I
F
D
E
37.4254.076.00 11/2015


Acondicionador de aire de consola partida sistema split
KPA8FIA0R5IBA
KPA9FIB0R5IBA




2
The following symbols used in this manual, alert you
to potentially dangerous conditions to users, service
personnel or the appliance:
This symbol refers to a hazard or unsafe practice which
can result in severe personal injury or death.
This symbol refers to a hazard or unsafe practice which can
result in personal injury or product or property damage.
This air conditioner is equipped with cooling, drying, heating and fan only functions.
Details on these functions are provided below; refer on these descriptions when using the air conditioner.

NAME OF PARTS AND OPERATION SELECTOR SWITCH 3
INSTALLATION LOCATION 4
ELECTRICAL REQUIREMENTS 4
SAFETY INSTRUCTIONS 4
USING THE REMOTE CONTROL UNIT 4
REMOTE CONTROL UNIT 5
HOW TO SET THE PRESENT TIME 6
COOLING 6
HEATING 6
AUTOMATIC OPERATION 6
DEHUMIDIFYING (DRY) 7
FAN ONLY 7
ADJUSTING THE FAN SPEED 7
NIGHT MODE/ENERGY SAVING 7
HIGH POWER MODE 7
SETTING THE TIMER 8
SETTING THE 1 HOUR TIMER 8
SETTING THE HOLIDAY TIMER 8
ADJUSTING THE AIR FLOW DIRECTION 9
OPERATION WITHOUT THE REMOTE CONTROL UNIT 10
CARE AND CLEANING 10
TIPS FOR ENERGY SAVING 11
TROUBLESHOOTING 11
EXPLANATION AND USE OF THE REMOTE CONTROL UNIT’S MICROSWITCHES 15
NOTE

If you have problems or questions concerning your Air
Conditioner, you will need the following information. Model
and serial numbers are on the nameplate on the bottom
of the cabinet.
Model No.
Serial No.
Date of purchase
Dealer’s address
Phone number

EG
WARNING


This product is marked as it satisfies Directives:
– Low voltage no. 2006/95/EC (Standard: EN60335-2-40:2003 (incl. Corr.:2006) + A11:2004 + A12:2005 + A13:2012
+ A1:2006 + A2:2009 con EN 60335-1:2002 + A11:2004 + A1:2004 + A12:2006 + A2:2006 + A13:2008 + A14:2010
+ A15:2011).
– Electromagnetic compatibility no. 2004/108/EC, 92/31 EEC and 93/68 EEC. (Standard: EN55014-1 (2006) +
A1(2009) + A2(2011), EN 55014-2 (1997) + A1(2001) + A2 (2008), EN 61000-3-2 (2006) + A1(2009) + A2(2009),
EN 61000-3-3 (2008)
– RoHS2 no.2011/65/EU.
– Regulation (EU) no. 206/2012, of 6 march 2012, concerning the specifications for ecodesign requirements of air
conditioners and fans.
– Regulation (EU) no. 626/2011, of 4 may 2011, concerning the labeling indicating the energy consumption of air
conditioners.
This declaration will become void in case of misuse and/or non observance though partial of manufacturer’s
installation and/or operating instructions.

3
 
2. Remote control sensor: Detects the room temperature
around the remote control unit, the air conditioner is
controlled accordingly.
  Conditioned air is blown out of the air
conditioner through the air outlet.
4.
 Air from the room is drawn into this section
and passes through air filter which removes dust.
5. Remote control receiver: This section picks up infrared
signals from the remote control unit (Transmitter).
 Push
the button to walk through the operation modes (OFF,
COOL and HEAT)
7. OPERATION lamp: This lamp lights up during
operation.
It blinks once to announce that the remote control
signal has been received and stored.
  This lamp lights up when the air
conditioner is connected to the power and ready to
receive the remote control command.
 This lamp lights up when the system is
being controlled by the timer.


WARNING
EG

78 9
5
3
4
2
1
6

It is possible to set the air conditioner in order to let the
OPERATION, TIMER and STANDBY lamps always OFF,
even during operation.
Be sure that the remote controller is ON (using the ON/
OFF button) and that the symbol on the display of
remote controller is OFF, then Press contemporary the
IFEEL and FAN buttons on the remote control unit for more
then 5 seconds.
Repeat the same procedure to set again the normal
operation conditions.
If the air conditioner is powered, but the lamps are off, try
to activate them using this procedure.
In case of troubleshooting the air conditioner diagnostic
system activates the lamps accordingly, even if they are
set to OFF. See paragraph TROUBLESHOOTING for
further details.

OPERATION lamp ON, indicates that:
1. 
2. 
 
Select the correct mode, compatible with the
system.

 only

4
EG

l


l       



lNever use or store gasoline or other flammable vapor or
liquid near the air conditioner. It is very dangerous.
l


lThe manufacturer assumes no responsabilities if the
safety regulations or local codes are not observed.
l


lDo not let children play with the air conditioner.
l
are present.
l





WARNING


lWe recommend this air conditioner to be installed

    

lDo not install this air conditioner where there are


l

lDo not install the air conditioner where the



l


air near a spa.
WARNING

lBefore installation, check that the voltage of the electric
supply in your home or office is the same as the voltage
shown on the nameplate.
l All wiring must conform to the local electrical codes.
Consult your dealer or a qualified electrician for details.
lEach unit must be properly grounded with a ground (or
earth) wire or through the supply wiring.
lWiring must be done by a qualified electrician.

lRemove trhe lid in the rear part of the remote control
unit and check the settings of the four microswitches
as shown below:

l Under normal conditions the room temperature is
detected and checked by the temperature sensor placed
in the remote controller (I FEEL icon displayed ).This
function is designed to provide a comfortable room
temperature by transmitting the temperature control
command from the location next to you. When using this
function, the remote, control should always be pointed
at the air conditioner, therefore it should be placed in
a position in which it is visible by the indoor unit (for
example, do not put it in a drawer).
lIt is possible to disable the remote controller room
sensor pressing the I FEEL button. In this case the I
FEEL icon on the remote controller display lights off and
only the sensor placed in the air conditioner becomes
active.

lInsert two AAA alkaline batteries of 1,5 V-DC making
sure that point in the direction marked in the battery
compartment.The displayed time flashes.
Press the SEL TYPE button.
Remote controller is now ready for operation.
lThe batteries last average more than six months,
anyway it depends on how much you use the remote
control unit.
Remove the batteries if you do not use the remote
control unit for more than one month.
Replace the batteries when the remote control unit
lamp fails to light, or when the air conditioner does not
receive the remote control unit signals.
lThe batteries of the remote control contain polluted
substances. Exhausted batteries must be disposed
according to the laws in force.

When using the remote control unit, always point the unit
transmitter head directly at the air conditioner receiver.

Press the ON/OFF button to turn the air conditioner on.
The operation lamp will light up, indicating the unit is in
operation.









NOTE
SWITCHES
NOTE 










5
EG


Information is displayed when the remote controller is switched
on. If switched off, only the operating mode, the room temperature
and the clock are shown
Operation mode
Fan speed
High speed
Automatic Medium speed
Low speed
Displayed when
transmitting data
Set point
temperature
I FEEL mode is active
(remote controller
sensor active)
Timer modes
Automatic
Cooling
Heating
Dehumidification
Fan
C
Clock
Room
temperature
Night
mode
Oscillation
Flap
Filter Ti02is ON
HIGH POWER
mode

When you press
the buttons of the
remote control unit,
the mark
appears on the
display to transmit
the setting changes
to the receiver in the
air conditioner.
   

With these buttons is possible to set the
clock and the timer. For details refer to
paragraphs “ SETTING THE HOUR” and
“SETTING THE TIMER”.

Press this button to select the type of
timer to activate. For details refer to
paragraph “SETTING THE TIMER”.
C


Press this button to decrease the set
temperature.

Press this button to increase the set
temperature.
SENSOR
A temperature
sensor inside the
remote control unit
detects the room
temperature.

Press this button in order to:
• set the clock
• set the ON/OFF timer
For details refer to paragraphs “SETTING
THE HOUR” and “SETTING THE TIMER”.

Press this button to modify the active
setting for room temperature detection
(from remote controller to air conditioner
and viceversa).

Fan speed is automatically
selected by the
microcomputer.
High speed.
Medium speed.
Low speed.

This button turns the air conditioner ON
and OFF.

Press this button in order to select the
desired function.
Fixed: six position
Continous oscillations
Automatically oscillations

Press this button in order to select the
NIGHT/ECO mode.

Press this button in order to select the
HIGH POWER mode.

Press this button to modify the air
conditioner mode.

The air conditioner makes the room
cooler.

The air conditioner reduces the humidity
in the room.
 
When this setting is selected (+ IFEEL
ON), the unit calculates the difference
between the thermostat setting and
the perceived room temperature and
automatically switches to the “cool” or
“heat” mode.

The air conditioner works only as a
circulation fan.
Inverter model

Use this button in order to enter the
functions menu.

Press this button to modify the air
conditioner mode.

The air conditioner makes the room
warmer.
: the fan stops when the set
temperature is exceeded.
  
 : the
fan keeps running even after the set
temperature is exceeded.

When this setting is selected (+ IFEEL ON),
the unit calculates the difference between
the thermostat setting and the perceived
room temperature and automatically
switches to the “cool” or “heat” mode.

6
EG



When the outdoor temperature is low, frost or ice may
appear on the heat exchanger coil, reducing the heating
performance. When this happens, a protection function
for the heat exchanger defrosting is activated. During this
function operation, the fan of the indoor unit stops. Heating
operation restarts after several minutes. (This interval
will vary slightly depending on the room and outdoor
temperature).

A heat pump conditioner heats a room by taking heat
from outside air. The heating efficiency will fall off when
the outdoor temperature is very low. If enough heat is not
obtained with this air conditioner, use another heating
appliance in conjunction with it.
Example of operation diagram in the (Auto) mode
with the set room temperature at .
NOTE
The air conditioner changes the operation mode (from cool
to heat or vice versa, if one of the following conditions
occurs:
-  changes if the difference between the room
temperature and the temperature set on the remote
control unit is at least 3°C..
- changes if the difference between the room
temperature and the temperature set on the remote
control unit is at least 1°C, one hour after the compressor
stop.
-  never changes if the difference between the
room temperature and the temperature set on the remote
control unit is no more than 1°C.
1.Set the or selector to AUTO (symbol on the
display; also the symbol or remains displayed).
2.Press the
+/- buttons (temperature selection) to set the
desired temperature (the temperature range is between
32 °C max. and 10 °C min.).
When this setting is selected, the air conditioner will operate
automatically switching to the COOL or HEAT mode as
appropriate (regardless of the symbol displayed).
THE DISPLAY SHOWS THE
SELECTED TEMPERATURE.
AFTER 5 SECONDS FROM THE
REQUIRED TEMPERATURE SETTING
THE DISPLAY WILL SHOW THE ROOM
TEMPERATURE AGAIN.
3.Press the FAN selector button to the setting you want.
During Automatic Operation (+ IFEEL ON) the set
temperature is understood as perceived one, then the
system is automatically adjusted not only according to the
air temperature, but also based on the relative humidity,
according to the “humidex” index.
Verify that the unit is connected to the
main power and the STANDBY lamp is
light up.
1.Set the selector to COOL (symbol
on the display).
2. Press the +/- buttons (temperature
selection) to set the desired temperature
(the temperature range is between 32 °C
max. and 10 °C min.).


1. Press the button ST three times.
The time indication alone flashes.
2. Press the H button until the present time hour is
displayed. Press the M button until the present time
minutes are displayed. The display will automatically
stop flashing.
1.Set the selector to HEAT (fixed or blinking symbol
on the display.
2. Press the +/- buttons (temperature selection) to set
the desired temperature (the temperature range is between
32 °C max. and 10 °C min.).
THE DISPLAY SHOWS THE
SELECTED TEMPERATURE.
AFTER 5 SECONDS FROM THE
REQUIRED TEMPERATURE SETTING
THE DISPLAY WILL SHOW THE ROOM
TEMPERATURE AGAIN.
3.Press the FAN button to select the fan speed.
For several minutes after the start of heating operation, the
indoor fan will stop until the indoor heat exchanger coil has
warmed up sufficiently. This is because the COLD DRAFT
PREVENTION SYSTEM is operating. During this period,
the STANDBY lamp remains lit.
NOTES

THE DISPLAY SHOWS THE
SELECTED TEMPERATURE.
AFTER 5 SECONDS FROM THE
REQUIRED TEMPERATURE SETTING
THE DISPLAY WILL SHOW THE ROOM
TEMPERATURE AGAIN.
3.Press the FAN button to select the fan speed.
NOTE
C
1
3
22
1
Generally the fan stops when the set temperature is
exceeded (when you have selected the fixed HEATING
symbol ).

If you want to let the fan run even after the set temperature is
exceeded, for example, in order to make the heating, coming
from a nearby source, circulate (eg. fireplace installed under
the air conditioner), press the selector until the blinking
HEATING symbol is displayed.
ONON ON
∆ 1 H ∆ 1 H
MIN.MAX.
A
B
C
C
B
A
27
26
25
24
23
22
21
20
19

7
EG
1.Set the button to DRY. The icon is displayed.
2.Press the +/- buttons (temperature selection) to set the
desired temperature (the temperature range is between
32 °C max. and 10 °C min.).

THE DISPLAY SHOWS THE
SELECTED TEMPERATURE.
AFTER 5 SECONDS FROM THE
REQUIRED TEMPERATURE SETTING
THE DISPLAY WILL SHOW THE ROOM
TEMPERATURE AGAIN.
lUse DRY operation when you want to reduce the humidity
in the room.
lDehumidifying operation is adjusted both by the difference
between set temperature and air temperature, and by the
value of relative humidity, detected by the sensor.
lDuring DRY operation, the fan speed is automatically
set (Remote control lamp is ON) to prevent
overcooling.
lDry operation is not possible if the indoor temperature is
10 °C or less.
lWhen room temperature is above set value, the unit
operates to dehumidificate so efficient as possible.
lWhen room temperature is below set value, the unit will
not stop, it will proceed operating with low power to
dehumificate and, in small spaces, temperature could
drop below the set temperature.
NOTE

If you want to make air circulate without any temperature
control, press button until only the fan symbol
appears on the display.


Simply set the FAN selector to the position.The unit
automatically controls the fan speed when the AUTO mode
is selected. When the air conditioner starts operating, in
heating or cooling, the fan speed varies according to the
thermal load of the room.

If you want to manually adjust speed just set the FAN
selector as desired.
High speed Med. speed Low speed
   

When the air conditioning system configuration is multisplit
and there is more than one indoor unit connected, the
automatic mode operates as follows:
- the first unit that switches on the system also decides the
operation mode (cooling or heating) for all the other units
that will be switched on after the first one;
- when the system has been switched on in cooling mode
and one unit is activated in heating mode, an error will
be signaled for this unit (wrong operating mode). If the
same unit is switched on in “automatic” mode and the
desired temperature is lower than the detected ambient
temperature, the unit will operate in cooling mode, like the
other units of the system; on the contrary, if the desired
temperature is higher than the detected one, the unit will
operate in fan mode;
- when the system has been switched on in heating mode
and one unit is activated in cooling mode, an error will
be signaled for this unit (wrong operating mode). If the
same unit is switched on in “automatic” mode and the
desired temperature is higher than the detected ambient
temperature, the unit will operate in heating mode, like the
other units of the system; on the contrary, if the desired
temperature is lower than the detected one, the unit will
operate in fan mode.

lThis mode enables you to save energy.
1. Set the or selector to cool, dry or heat.
2. Press the button.
3. The mark appears on the display. Press the
button again to release the function.

When you select the NIGHT mode, the air conditioner will
modify automatically the set temperature after 60 minutes.
This enables you to save energy without sacrificing your
comfort.
OPERATING MODE SET TEMPERATURE CHANGE
Heating Lowered by 2 °C
Cooling and Dry Raised by 1 °C
During the NIGHT mode the internal fan speed is
automatically lowered and reduces the noise.
NOTA
NOTE
During the high power operation the room temperature
could not correspond to the set temperature.

When this mode is active the internal fan speed is set
automatically and the air conditioner operates at the
maximum power in the selected operating mode (cooling
or heating).
1.Press the HIGH POWER button.
3.The mark appears on the display.
Press the button
again to release the function. .

8
EG

1. Press the ST button once.
The ON and time indications flash.
2. Press the H button until the designed
hour is displayed.
Press the M button until the designed
minutes are displayed. The display
will change automatically back to
show the present time after 10 sec.
3. Press the ON/OFF button to start the
air conditioner.
4. Press the button to activate the
ON timer.

1. Press the ST button twice.
The OFF and time indications flash.
2. Press the H button until the designed
hour is displayed.
Press the M button until the designed
minutes are displayed. The display will
change automatically back to show
the present time after 10 sec.
3. Press the ON/OFF button to start the
air conditioner.
4. Press the button two times to
activate the OFF timer.
   
 

1. Set the timer ON/OFF as shown in A)
and B).
2. Press the ON/OFF button to start the
air conditioner.
3. Press three times the button to
activate the DAILY timer.

After timer setting, press ST button in order to check the
ON/OFF setting time.
NOTE
TIMER SETTING PROCEDURE.
lPress four times the button.The 1
HOUR TIMER mark will appear on the
display.
CANCELLATION PROCEDURE
lPress the ON/OFF button to turn the air conditioner off.
lWait for the indoor unit to stop operating.
lPress the ON/OFF button again to turn the air conditioner
on.

This function causes the unit to operate for one hour at the
set conditions, regardless of whether the unit is on or off.
C
4
2
2
3
1

The Holiday Timer function allows you to activate the
indoor unit (either it is the only one of a monosplit system
or one unit of a multisplit system), with a dalay up to
99 days you can set for the Daily Timer, On Timer, Off
Timer functions (not available for 1 HOUR TIMER) already
explained in this manual.
With this function you can set the air conditioner to be
switched on again after a long week end, a holiday of one
week or more, ecc…
To activate this function you have to follow the following
steps in order :
1. Keep pressed the button “TIMER SELECTION” of the
remote control unit (clock figure) for more than 6~7
seconds. In this way you enter the menu to select the
number of days of delay.
2. Select the desired timer (Daily Timer, On Timer,
Off Timer) pressing on the same button “TIMER
SELECTION”.
3. Set the desired number of days of delay using the
button “+” .
4. Keep pressed again the button “TIMER SELECTION”
for more than 6~7 seconds. You enter again the normal
menu of the remote control unit.
At this point, the symbol of the desired timer will flash
and the selected timer will be activated only after the set
number of delay days.
C

3

9
EG


The horizontal air flow can be adjusted by moving the
vertical vanes to the left or right, as indicated in the
following figures.

Make sure that the remote control unit has been turned on. Press
the FLAP button to select the flap function


position

oscillations

oscillations



NOTES lThe flap automatically closes when the unit
is off.
lWhen the unit starts in heating operation,
the fan stops and the flap is in the 4 position
(if automatical oscillation is selected) until
the air being blown out of the unit begins
to warm. Once the air warms up, the flap
position and fan speed change to the
settings specified with the remote control.









the air vent and drip down.








VERTICAL VANE
DEFLETTORE
40°
50°
Zone «A»
for cooling and dehumidifyng
Zone «B»
for heating
40°
50°
«B»
«A»
«B»
«A»

10
EG

Use a vacuum cleaner to remove light dust. If there is
sticky dust on the filter, wash the filter in lukewarm,
soapy water, rinse it in clean water, and dry it.

AIR
The filter behind the front panel should be checked and
cleaned at least once every two weeks.
lNever use solvents, or harsh chemicals when cleaning
the indoor unit. Do not wipe the plastic casing using very
hot water.
lSome metal edges and the vanes are sharp and may
cause injury if handled improperly; be especially careful
when you clean these parts.
lThe internal coil and other components of the outdoor
unit must be cleaned every year. Consult your dealer or
service centre.

2. 
If you want to turn off the air conditioner push the
OPERATION selector with a pen until the OPERATION
lamp is turned off.

In the event of power failure, the unit will stop. When the
power is resumed, the unit will restart automatically after
3 minutes.
NOTE
If you have lost the remote control unit or it has troubles,
follow the steps below.
1. 
If you want to turn on the air conditioner push the
OPERATION selector with a pen to select the desired
mode (COOL or HEAT).





NOTE

lMaintenance operations must be carried out by specially
trained personnel.
lFor safety, be sure to turn the air conditioner off and also
to disconnect the power before cleaning.
lDo not pour water on the indoor unit to clean it. This will
damage the internal components and cause an electric
shock hazard.
WARNING

Clean the casing and grille of the indoor unit with a vacuum
cleaner brush, or wipe them with a clean, soft cloth.
If these parts are stained, use a clean cloth moistened with
a mild liquid detergent.
When cleaning the grille, be careful not to force the vanes
out of place.
OPERATION
selector
1.Grasp both ends of the air intake grille and pull to open
it.
2.Hold the air filter by the tab and pull it upward. Clean
the air filter.
3.When replacing the filter, make sure that the FRONT
mark is facing you. Reinsert the filter into place and close
the air intake grille.
2
1
FRONT
4
3

11
EG

DO NOT:
lBlock the air intake and outlet of the unit.
If they are obstructed, the unit will not work well, and
may be damaged.
lLet direct sunlight into the room. Use sunshades,
blind or curtain.
DO:
lAlways try to keep the air filter clean. A clogged filter
will impair the performance of the unit.
lTo prevent conditioned air from escaping, keep
windows, doors and any other openings closed.

WARNING
lThe use of portable telephones near the air conditioner
may cause disturbance to its normal operation and must
be avoided. In case abnormal operation is noticed,
(OPERATION lamp lights, but the air conditioner will not
run) to restore normal operation turn-off electric supply
for about 3 minutes, by disconnecting the main switch
or the wall plug, then start again the air conditioner.
If your air conditioner does not work properly, first check
the following points before requesting service.
If it still does not work properly, contact your dealer or
service centre.
 the air conditioner does not run at all.

1. Power failure.
2. Leakage breaker tripped.
3. Operation button is OFF.
4. Batteries in remote control unit have run down.
Remedy:
1. Restore power.
2. Contact service centre.
3. Press the button again.
4. Replace batteries.
 Poor cooling or heating performance.

1. Dirty or clogged air filters.
2. Heat source or many people in room.
3. Doors and/or windows are open.
4. Obstacle near air intake or air discharge port.
5. The set temperature on the remote control unit is too
high.
6. Outdoor temperature is too low (heat pump version).
7. Defrosting system does not work (heat pump version).
Remedy:
1. Clean air filters to improve airflow.
2. Eliminate heat source if possible.
3. Shut them to keep the heat or cold out.
4. Remove it to ensure good airflow.
5. Set the right temperature on the remote control unit.
6. Try to use a back-up heater.
7. Consult your dealer.
 Clicking sound is heard from the air conditioner.

1. During operation, any plastic parts may expand or
shrink due to a sudden temperature change. In this
event, a clicking sound may occur.
Remedy:
1. This is normal, and the sound will disappear when an
even temperature is settled.
   

NOTE
1. The activated carbon air filters are in a polyethylene
bag.
2. Open the bag just before installing the activated carbon
air filters, otherwise, the deodorizing effect durability of
the filter may be decreased.
The activated carbon air filter is to be added to the
standard filter.
It is made of two layers:
- the first layer consists in a synthetic honey comb high
efficiency media to remove the dust and purifing the
air.
- the second layer in charcoal media deodorizing the
ambient air.


lThe filter is disposable.
lDo not throw away the filter frame, if present.
lThe used filter cannot be reused even after cleaning up.
lObtain the filters for replacement at your nearest dealer.
lCheck the state of dirtiness at least once every two
weeks.
lReplace the filter after six months’ operation.
This activated carbon air filter cannot remove harmful
gases or vapors nor ventilate air in the room. You must
open doors or windows frequently when you use gas or oil
heating appliances. Otherwise there is a risk of suffocation
in an extreme case.
WARNING


1. Open the unit intake air grille and pull out the standard
air filter.
2. Apply on the rear side of the filter the two spings
supplied with the accessory.
3. Fix the activated carbon filter by the springs.
4. Insert the two air filters one over the other and close
the intake grille.
REAR SIDE OF
AIR FILTER
SPRING
ACTIVATED CARBON
FILTER

12
EG
ERROR LEDS
OPERATION TIMER STANDBY POSSIBLE CAUSE SYSTEM BEHAVIOUR SOLUTION
E0 lF F
Unit has not been addressed correctly. Operating mode selected is not compatible with the system (ex. heating mode has been selected, when the system was in cooling mode, or vice versa).
Fan is stopped and flap is closed. The system restarts automatically as soon as the unit is addressed correctly. Fan is stopped and flap is closed. The system restarts automatically as soon as a correct operating mode is selected.
Set the outdoor/indoor unit refrigerant circuit address (see Installation Instructions) Select an available or compatible mode with the other units of the system.
E1 O O F
Error on the outdoor unit. Fan is stopped and flap is closed.
The system restarts automatically as soon as the problem on the outdoor unit is solved.
Check the error code using the appropriate LEDs on the PCB of the outdoor unit. Follow the indications of the diagnosis for the outdoor unit.
 O = LED OFF l = LED ON F = Flashing LED

13
EG
ERROR LEDS
OPERATION TIMER STANDBY POSSIBLE CAUSE SYSTEM BEHAVIOUR SOLUTION
E3 F F F
Communication error between the outdoor unit and the indoor unit
Fan is stopped and flap is closed after 30 seconds of missing communication. The system restarts automatically as soon as the communication is recovered.
Check that connections between C1 and C2 on outdoor and indoor terminal block are correct (C1 terminals connected together, C2 terminals connected together). Check that a shielded communication cable has been used. Check that the dip-switch SW2 for communication address setting is in the correct position. Check that all earth cables are properly connected to every terminal. Check that the shield of the communication cable is properly connected to every terminal. Check the communication fuse on outdoor and indoor unit. Check that the outdoor unit has power supply and that it is working. Check that all PCBs are powered on. Be sure that power supply has not been connected to the communication terminals. Check that there are no burnt signs on the PCBs, in particular close to communication cables. Check that the fan motor is not damaged and it doesn’t create short circuit on the indoor PCB.
O = LED OFF l = LED ON F = Flashing LED

14
EG
ERROR LEDS
OPERATION TIMER STANDBY POSSIBLE CAUSE SYSTEM BEHAVIOUR SOLUTION
E4 F F O
Defective or not connected indoor coil temperature sensor.
Fan is stopped and flap is closed. The system restarts automatically as soon as the sensor is repaired.
Check that the sensor is properly connected to the PCB as shown in the electrical wiring diagram. Check that the sensor is not damaged and, if necessary, replace it.
E5 F O F
Defective or not connected room air temperature/humidity sensor.
Fan is stopped and flap is closed. The system restarts automatically as soon as the sensor is repaired.
Check that the sensor is properly connected to the PCB as shown in the electrical wiring diagram. Check that the sensor is not damaged and, if necessary, replace it.
E6 O F F
Fan motor error. Fan is stopped and flap is closed.
The system restarts automatically after some seconds.
Check that the fan motor is properly connected to the PCB as shown in the electrical wiring diagram. Check that the fan motor is not locked. Check that the fan motor is not damaged and, if necessary, replace it.
E8 O F O
Combination between outdoor unit and indoor units is not correct.
Fan is stopped and flap is closed. Check that you have selected, during
the installation of the system, a proper combination between outdoor unit and indoor units. Check that none of the indoor units of the system has a communication error. If present, first solve this error.
 O = LED OFF l = LED ON F = Flashing LED

15


At the end of its working life this equipment must not be disposed of as an household waste.
It must be taken to special local community waste collection centres or to a dealer providing this service.
Disposing of an electrical and electronic equipment separately avoids possible negative effects on the environment
and human health deriving from an inappropriate disposal and enables its components to be recovered and recycled
to obtain significant savings in energy and resources.
In order to underline the duty to dispose of this equipment separately, the product is marked with a crossed-out dustbin.


Please replace battery when its electricity charge is used up: please do not eliminate this battery together with normal
household waste. It must be taken to special local community waste collection centres or to a dealer providing this
service. Disposing of a battery separately avoids possible negative effects on the environment and human health
deriving from an inappropriate disposal and enables its components to be recovered and recycled to obtain significant
savings in energy and resources. In order to underline the duty to dispose of this equipment separately, the battery
is marked with a crossed-out dustbin.

The unit contains R410A, a fluorinated greenhouse gas with a global warming potential (GWP) of
2087.50. Do not release R410A into the atmosphere.

Switch 1 and 2: These switches are used to match the remote control with the
specific internal units.
Switch 3 and 4: these switches have been provided for future use; they have no
function today. Keep them in OFF position.
Switch 5 and 6: these switches set the remote control in WIRELESS or WIRED
mode. Default position is ON (WIRELESS mode). For WIRED control, remove the
batteries and set in OFF position.

lRemove the lid.
lPress the battery toward the negative end
and lift it out by its positive end (as shown
in the figure).
lRemove the other battery in the same way.
EG

Z.I. Route départementale 28
01600 Reyrieux France
Tél. [phone] - Fax [phone]
Technibel is a trademark of NIBE ENERGY SYSTEM FRANCE